Biomedical Engineering and Bioengineering Commons^™

The Study Of Corrosion On Additive-Manufactured Metals., Braydan Daniels

Electronic Theses and Dissertations

The purpose of this study was to investigate and compare the corrosion mechanisms between wrought and additive-manufactured (3D-printed) copper and stainless steel. The experimental procedure consisted of measuring the open circuit potential, electrochemical impedance spectroscopy, linear sweep voltammetry, Tafel analysis, surface topology, and scanning electron microscopy for each metal within salt water, tap water, sulfuric acid, and synthetic body fluid (excluding copper in synthetic body fluid).

Overall, printed stainless steel was more corrosion-resistant than wrought stainless steel in tap water and synthetic body fluid based on OCP, LSV, and surface topology results. Additionally, printed copper was more corrosion-resistant than wrought …

An Experimental Study On The Mechanical Properties And Chemical Composition Of Lcd 3d Printed Specimens, Sebastian Gomez

Electronic Theses and Dissertations

Additive manufacturing technologies have been enhanced throughout the years yet have surprised the manufacturing industry due to their high-end surface finish and dimensional accuracy. Different experiments have been done to identify a specific phenomenon known in the vat-polymerization field. Distortion and dimensional inaccuracy tend to affect the overall properties of the process, either physical or chemical. This approach allows the understanding of how the physical properties have been affected and how to study the chemical properties to avoid this type of phenomenon. The chemical reaction between polymer and UV light has been studied and experimented with to the point that …

Real-Time Monitoring Of Cell Death Progress Using Capacitance Spectroscopy, Suyang Wu

Electronic Theses and Dissertations

Biologics, including the monoclonal antibody (mAb), has experienced rapid development in the last decade. However, the price of biologics is often prohibitively high because of the low process efficiency. Delaying the inevitable cell death improves the productivity of upstream bioprocessing, whose success relies on monitoring the cell death onset that indicates the timing for preventive actions.

This study proposes to develop a real-time monitoring model that quantifies the dying cell percentage in lab-scale bioreactors using capacitance spectroscopy. The capacitance spectroscopy contains cell death-related information due to various physical properties changes during the cell death process, e.g., cytoplasmic conductivity change. The …

The Use Of Nanoparticles And Electrospun Fibers For Intravaginal Delivery To Treat Viral And Bacterial Infections And Electrophysiological Measurements Of Synthetic Chloride Channels., Farnaz Minooei

Electronic Theses and Dissertations

Female reproductive viral and bacterial infections affect millions of women worldwide. Given the diversity and magnitude of these unmet reproductive health challenges, topical administration of antiretrovirals (ARVs) and antibiotics have emerged as promising approaches to maintain and restore reproductive health. However, currently available intravaginal dosage forms often suffer from low user adherence and the need for frequent, daily administration to achieve therapeutic effect. To address these challenges, the broad goal of this research was to focus on the development of new localized nanoparticle (NP) and electrospun fiber dosage forms to prolong the delivery and enhance the efficacy of active agents …

Fabrication Of Silicon Microneedles For Dermal Interstitial Fluid Extraction In Human Subjects, Caleb A. Berry

Electronic Theses and Dissertations

The goal of this project is to design and develop a fabrication process for silicon microneedle arrays to extract dermal interstitial fluid (ISF) from human skin. ISF is a cell- free, living tissue medium that is known to contain many of the same, clinical biomarkers of general health, stress response and immune status as in blood. However, a significant barrier to adoption of ISF as a diagnostic matrix is the lack of a rapid, minimally invasive method of access and collection for analysis. Microfabricated chips containing arrays of microneedles that can rapidly and painlessly access and collect dermal ISF for …

A Computer Science Approach To Identify And Classify Hyperactivated Spermatozoa, Norbert Kaula

Electronic Theses and Dissertations

Effective Assisted Reproductive Technology (ART) relies in part upon accurate but easily conducted measurements of sperm motion parameters. Several established methods are widely used to assess possible reasons for male infertility, in human and veterinary Andrology clinics. Computer-assisted sperm analysis (CASA) devices quantitatively assess sperm motion parameters, which have been defined by the World Health Organization, and include the percentage of motile cells in a sample and the motion characteristics of individual cells, such as curvilinear velocity (VCL), average path velocity (VAP) and straight line velocity (VSL). However, CASA analyses fail to define hyperactive sperm motility or determine the prevalence …