Automotive Engineering Commons^™

Basic Utilities Vehicle (Buv) Milk Transportation, Brian D. Reynolds, Sean Patrick Bayless Galligar, Emmitt Hanner, Joshua T. Pitts

Scholar Week 2016 - present

In developing countries, a need exists for the transportation of raw foods to communities without spoilage. Traditional methods of transporting goods don’t meet the needs of the consumer, and often times food is wasted due to the harsh climate and time constraints. Food often becomes salvage under the heat, causing a hurt to the profitability of vendors and family needs for fresh produce. In particular milk transportation has become difficult, due to the lack of cold storage in standard transit. As a response to the need for affordable raw food transport, our sponsor Basic Utilities Vehicle (BUV) has tasked us …

Fluid Power Vehicle Challenge, Jacob Torrey, Kayla Londono, Bryson Chan, Aaron Trujillo

Mechanical Engineering

The FPVC combines mechanical engineering disciplines to design and manufacture a vehicle that utilizes hydraulic power. The FDR covers the final manufacturing process and verification processes developed during the front end of research and analysis built upon the Critical Design Review (CDR) and the PDR (Preliminary Design Review). This report showcases the design decisions and extensive research that supports the continuing efforts by the Team Pump My Ride, to build upon the accomplishments of Cal Poly’s previous team, The Incompressibles. The FDR presents how Team Pump My Ride produced the design changes from the CDR and PDR to achieve improvements …

Development Of An Eco Approach And Departure Application To Improve Energy Consumption Of A Plug-In Hybrid Vehicle In Charge Depleting Mode, Brandon Narodzonek

Dissertations, Master's Theses and Master's Reports

A recent study at Michigan Technological University as part of the NEXTCAR DOE APRA-E Project was conducted to determine the potential energy savings of a plug-in hybrid electric vehicle (PHEV) equipped with various Connected and Automated Vehicle (CAV) Technologies. One aspect of this study focused on the development of an Eco Approach and Departure (Eco AnD) Application that would further reduce the energy consumed around a signalized intersection.

Many modern intersections are equipped with traffic signals that can broadcast Basic Safety (BSM), MAP, and Signal Phase and Timing (SPaT) message sets that contain intersection ID, location, current phase, and cyclic …

Real-Time Predictive Control Of Connected Vehicle Powertrains For Improved Energy Efficiency, Joseph Oncken

Dissertations, Master's Theses and Master's Reports

The continued push for the reduction of energy consumption across the automotive vehicle fleet has led to widespread adoption of hybrid and plug-in hybrid electric vehicles (PHEV) by auto manufacturers. In addition, connected and automated vehicle (CAV) technologies have seen rapid development in recent years and bring with them the potential to significantly impact vehicle energy consumption. This dissertation studies predictive control methods for PHEV powertrains that are enabled by CAV technologies with the goal of reducing vehicle energy consumption.

First, a real-time predictive powertrain controller for PHEV energy management is developed. This controller utilizes predictions of future vehicle velocity …

Measurement Of Current Distribution In The Land Channel Direction Of A Proton Exchange Membrane Fuel Cell, Chinmay Kulkarni

Dissertations, Master's Theses and Master's Reports

A fully functional proton exchange membrane fuel cell with single land channel geometry on the cathode and segmented anode current collector with 9 mm² active area with a 350μm spatial resolution was utilized to measure the local current distribution in the land channel direction. A distinguished printed circuit board approach was used for the data acquisition to adapt to any flow field design.

Performance of this segmented cell was examined at dry, wet and moderate humidity settings to study the water transport phenomenon in the PEMFC. In the dry condition at 60 ͦ C with 0% relative humidity, the …

An Examination To Pathways Powering Car Using Clean Energy, Marina Miranda

Graduate Theses, Dissertations, and Problem Reports

Traditional vehicles powered by internal combustion engines contribute significantly to increasing emissions of greenhouses gasses (GHG). There has been increasing interest in powering vehicles using green energy include using electricity produced by wind turbine and solar panel. The green electricity can be used to directly charge the Battery Electric Vehicles (BEV), or producing hydrogen as fuel for Fuel Cell Electric Vehicles (FCEV) by converting electrical energy to hydrogen (H₂) through water electrolysis. The low energy density H₂ produced can be stored on board as either compressed H₂ or liquefied H₂.

This research examines the …

Piezoelectric Energy Harvester Improvement, Nathan Embaugh, Jason Mack, Jeremiah Fitzgerald, Zachary J. Lindsey

Williams Honors College, Honors Research Projects

The energy harvester is used to convert a portion of the tire deflection waste energy to power up tire embedded sensors. A piezoelectric energy harvester is designed and some preliminary tests are done on it. So far, it has been shown that this design is sufficient for tire application. The team will need to modify the design of the energy harvester, the measurement setup and add a temperature and a strain senor to the existing setup so that the tire deflection and temperature can be measured and at the same time the energy harvester should be tested to see how …