Aerospace Engineering Commons^™

A Decoupled Engineering Methodology For Accurate Prediction Of Ablative Surface Boundary Conditions In Thermal Protection Systems, Justin Cooper

Theses and Dissertations--Mechanical Engineering

The main objective of the present work is to demonstrate a method for prediction of aerothermal environments in the engineering design of hypersonic vehicles as an alternative to the current heritage method. Flat plate and stagnation point boundary layer theory require multiple assumptions to establish the current engineering paradigm. Chief among these assumptions is the similarity between mass and heat transfer. Origins of these assumptions are demonstrated and their relationship to conservative engineering design is analyzed, as well as conditions where they possibly break down. An alternative approach for assessing aerothermal environments from the fluid domain is presented, which permits …

Kentucky Re-Entry Universal Payload System (Krups): Hypersonic Re-Entry Flight, John Daniel Schmidt

Theses and Dissertations--Mechanical Engineering

The Kentucky Re-entry Universal Payload System (KRUPS) is a small capsule designed as a technology testbed for re-entry experiments. For its first incarnation, KRUPS has been designed to test Thermal Protection Systems (TPS) and instruments in re-entry flights. Because of the unique environment a vehicle undergoes during re-entry, there is a high-demand for experimental data from re-entry experiments. KRUPS has been developed at the University of Kentucky (UK) over the past seven years to meet this demand. After completing sub-orbital campaigns, the first KRUPS hypersonic re-entry mission was attempted. The mission involved building three 11-inch diameter capsules each outfitted with …

The Kentucky Re-Entry Universal Payload System (Krups): Orbital Flight, James Tyler Nichols

Theses and Dissertations--Mechanical Engineering

Due to the uniqueness of atmospheric entry environments, ground facilities cannot accurately replicate re-entry conditions. Consequently, scientists primarily rely on numerical models to predict these conditions and inform Thermal Protection System (TPS) designs. These models often lack flight validation, which is necessary for increasing their fidelity. Thus, there is a substantial need to obtain such data to advance modeling capabilities.

The Kentucky Re-entry Universal Payload System (KRUPS) is an adaptable test-bed for scientific experimentation with initial application to TPS. This vehicle was designed at the University of Kentucky to serve as an inexpensive means of obtaining validation data to enhance …

Structural Optimization Of Space Transit Vehicle Concept, Hercules, James Philip Rogers

Theses and Dissertations--Mechanical Engineering

STRUCTURAL OPTIMIZATION OF SPACE TRANSIT VEHICLE CONCEPT, HERCULES:

A COMPARATIVE STUDY OF STRUCTURAL OPTIONS

Hercules is a vehicle concept developed by NASA Langley's Vehicle Analysis Branch to satisfy the need for sustainable transit between Earth, the moon, and Mars. Hercules features unprecedented abort capabilities and mission flexibility to aid in NASA's Mars campaign. By utilizing modern software to perform structural analysis and optimization for a large selection of stiffened panel concepts, beam concepts, and materials trends in the structural optimization emerge. These trends will be invaluable for the design of future spacecraft needed to fulfill similar roles.

The structural optimization …

Development Of Universal Solver For High Enthalpy Flows Through Ablative Materials, Umran Duzel

Theses and Dissertations--Mechanical Engineering

Atmospheric entry occurs at very high speeds which produces high temperature around the vehicle. Entry vehicles are thus equipped with Thermal Protection Systems which are usually made of ablative materials. This dissertation presents a new solver that models the atmospheric entry environment and the thermal protection systems. In this approach, both the external flow and the porous heat shield are solved using the same computational domain. The new solver uses the Volume Averaged Navier-Stokes Equations adapted for hypersonic non-equilibrium flow, and is thus valid for both domains. The code is verified using analytical problems, set of benchmarks and also a …

Single-Degree-Of-Freedom Experiments Demonstrating Electromagnetic Formation Flying For Small Satellite Swarms Using Piecewise-Sinusoidal Controls, Ajin Sunny

Theses and Dissertations--Mechanical Engineering

This thesis presents a decentralized electromagnetic formation flying (EMFF) control method using frequency-multiplexed sinusoidal control signals. We demonstrate the EMFF control approach in open-loop and closed-loop control experiments using a single-degree-of-freedom testbed with an electromagnetic actuation system (EAS). The EAS sense the relative position and velocity between satellites and implement a frequency-multiplexed sinusoidal control signal. We use a laser-rangefinder device to capture the relative position and an ARM-based microcontroller to implement the closed-loop control algorithm. We custom-design and build the EAS that implements the formation control in one dimension. The experimental results in this thesis demonstrate the feasibility of the …

Verification And Validation Studies For The Kats Aerothermodynamics And Material Response Solver, Olivia Schroeder

Theses and Dissertations--Mechanical Engineering

Modeling the atmospheric entry of spacecraft is challenging because of the large number of physical phenomena that occur during the process. In order to study thermal protection systems, engineers rely on high fidelity solvers to provide accurate predictions of both the thermochemical environment surrounding the heat shield, and its material response. Therefore, it is necessary to guarantee that the numerical models are correctly implemented and thoroughly validated. In recent years, a high-fidelity modeling tool has been developed at the University of Kentucky for the purpose of studying atmospheric entry. The objective of this work is to verify and validate this …

Comparisons Of Ablator Experimental Performance To Response Modeling And Effects Of Water Phase Transition In Porous Tps Materials, David L. Smith

Theses and Dissertations--Mechanical Engineering

The Mars Science Laboratory Entry Descent and Landing Instrumentation (MEDLI) project performed extensive arc jet tests for development, qualification, and calibration of instrumented heat shield plugs. These plugs each contained several thermocouples for recording near-surface and in-depth temperature response of the Phenolic Impregnated Carbon Ablator (PICA) heat shield. The arc jet test results are entered into a comprehensive database so that broad trends across the test series can be compared. One method of analysis is to compare with ablator material response calculations and solve the in-depth heat conduction equations. Using the near-surface thermocouple measurements as a boundary condition in numerical …

A Design Pathfinder With Material Correlation Points For Inflatable Systems, Jared T. Fulcher

Theses and Dissertations--Mechanical Engineering

The incorporation of inflatable structures into aerospace systems can produce significant advantages in stowed volume to mechanical effectiveness and overall weight. Many applications of these ultra-lightweight systems are designed to precisely control internal or external surfaces, or both, to achieve desired performance. The modeling of these structures becomes complex due to the material nonlinearities inherent to the majority of construction materials used in inflatable structures. Furthermore, accurately modeling the response and behavior of the interfacing boundaries that are common to many inflatable systems will lead to better understanding of the entire class of structures. The research presented involved using nonlinear …

Multidimensional Modeling Of Pyrolysis Gas Transport Inside Orthotropic Charring Ablators, Haoyue Weng

Theses and Dissertations--Mechanical Engineering

During hypersonic atmospheric entry, spacecraft are exposed to enormous aerodynamic heat. To prevent the payload from overheating, charring ablative materials are favored to be applied as the heat shield at the exposing surface of the vehicle. Accurate modeling not only prevents mission failures, but also helps reduce cost. Existing models were mostly limited to one-dimensional and discrepancies were shown against measured experiments and flight-data. To help improve the models and analyze the charring ablation problems, a multidimensional material response module is developed, based on a finite volume method framework. The developed computer program is verified through a series of test-cases, …