Aerospace Engineering Commons^™

A Comparison Of The Aerodynamic Centers For Panel Code Compressible Corrections And Openfoam 5 For Mach 0.1 To 0.8, Dustin Weaver

All Graduate Plan B and other Reports, Spring 1920 to Spring 2023

It is known that the aerodynamic center changes from quarter chord to half chord from incompressible to compressible flows on airfoils. Compressible corrections are derived and implemented in a vortex panel code. These results will be used to find the aerodynamic centers for the specified Mach range of 0.1 to 0.8 in 0.1 increments within - 6 to 6 degrees angle of attack. OpenFOAM 5 cases will be created with specific meshes and settings. The results calculated from OpenFOAM 5 will be compared to the results obtained from the compressible corrections.

Real Time And High Fidelity Quadcopter Tracking System, Tyler Mckay Hall

Computer Engineering

This project was conceived as a desired to have an affordable, flexible and physically compact tracking system for high accuracy spatial and orientation tracking. Specifically, this implementation is focused on providing a low cost motion capture system for future research. It is a tool to enable the further creation of systems that would require the use of accurate placement of landing pads, payload acquires and delivery. This system will provide the quadcopter platform a coordinate system that can be used in addition to GPS.

Field research with quadcopter manufacturers, photographers, agriculture and research organizations were contact and interviewed for information …

Manufacturing And Instrumentation Of An Open End Compressed Air Shock Tube, Josue O. Ruiz

Master's Theses

Shock tubes have been used extensively to study shock wave structures and high speed flow features. The purpose of constructing this open end shock tube was to have the ability to produce shock waves in a laboratory setting but also understand the exit flow coming out which can be applied to future studies that are beyond the scope of this work. This undertaking would require that an open end shock tube be built and instrumented with PCB Integrated Circuit Piezoelectric (ICP) Pressure Sensor Model 113B24 that would then be connected to a PCB Model 482C05 Signal Conditioner with the purpose …

Fdm Machine Learning: An Investigation Into The Utility Of Neural Networks As A Predictive Analytic Tool For Go Around Decision Making, John Bro

ASA Multidisciplinary Research Symposium

FDM MACHINE LEARNING: An investigation into the utility of neural networks as a predictive analytic tool for go around decision making.

Placing A High-Altitude Balloon In The Path Of Totality, Nicholas Jordan, Christopher Helmerich

2017 Academic High Altitude Conference

The UAH Space Hardware Club had conducted 70 flights prior to the Eclipse. In this time, we have gained valuable skills and experience which we have put into practice and passed on through the years. We put these skills into practice for the Eclipse. Our first challenge was finding where to launch. We started out by looking for suitable locations inside totality. We also examined a map of totality at 80,000 ft. We then ran predictions based on past weather during that time of year. By compiling multiple past predictions, we eliminated possible launch sites. We had multiple payloads, some …

Miniaturizing Ion Thruster Using Split Ring Resonator (Srr), Toyofumi Yamauchi, Gabriel Xu

Von Braun Symposium Student Posters

No abstract provided.

Autonomous Solid-State Radiation Detector For Safety Of Aerospace Systems, Levi Davies, Biswajit Ray

Von Braun Symposium Student Posters

No abstract provided.

Integrated Environment And Proximity Sensing For Uav Applications, Shawn S. Brackett

Electronic Theses and Dissertations

As Unmanned Aerial Vehicle (UAV), or “drone” applications expand, new methods for sensing, navigating and avoiding obstacles need to be developed. The project applies an Extended Kalman Filter (EKF) to a simulated quadcopter vehicle though Matlab in order to estimate not only the vehicle state but the world state around the vehicle. The EKF integrates multiple sensor readings from range sensors, IMU sensors, and radiation sensors and combines this information to optimize state estimates. The result is an estimated world map to be used in vehicle navigation and obstacle avoidance.

The simulation handles the physics behind the vehicle flight. As …

Mass Estimation Through Fusion Of Astrometric And Photometric Data Collection With Application To High Area-To-Mass Ratio Objects, Matthew Richardson

Master's Theses

This thesis work presents the formulation for a tool developed in MATLAB to determine the mass of a space object from the fusion of astrometric and photometric data. The application for such a tool is to better model the mass estimation method used for high area-to-mass ratio objects found in high altitude orbit regimes. Typically, the effect of solar radiation pressure is examined with angles observations to deduce area-to-mass ratio calculations for space objects since the area-to-mass ratio can greatly affect its orbital dynamics. On the other hand, photometric data is not sensitive to mass but is a function of …

Wing Deflection Analysis Of 3d Printed Wind Tunnel Models, Matthew G. Paul

Master's Theses

This work investigates the feasibility of producing small scale, low aerodynamic loading wind tunnel models, using FDM 3D printing methods, that are both structurally and aerodynamically representative in the wind tunnel. To verify the applicability of this approach, a 2.07% scale model of the NASA CRM was produced, whose wings were manufacturing using a Finite Deposition Modeling 3D printer. Experimental data was compared to numerical simulations to determine percent difference in wake distribution and wingtip deflection for multiple configurations.

Numerical simulation data taken in the form of CFD and FEA was used to validate data taken in the wind tunnel …

Atomic Oxygen Considerations For Leo De-Orbit Trajectories Using Solar Sails, Daniel A. Fugett

Master's Theses

Solar sails have the potential to benefit many future space exploration missions, but they lack the heritage required for present-day use. To grow confidence in solar sail technology, they could be deployed on LEO satellites higher than 600 km to help de-orbit the satellite within 25 years upon mission termination. To determine how atomic oxygen would affect the solar sail, material from Lightsail-2 was tested in a thermal-energy, isotropic, atomic oxygen vacuum chamber based in the space environments laboratory in California Polytechnic State University. The sail material, aluminized Mylar, was tested for its survivability on both the coated and uncoated …

Hybrid Buoyant Aircraft: Future Stol Aircraft For Interconnectivity Of The Malaysian Islands, Anwar Ul Haque, Waqar Asrar, Ashraf Ali Omar, Erwin Sulaeman, Jaffar Syed Mohamed Ali

Journal of Aviation Technology and Engineering

Hybrid buoyant aircraft are new to the arena of air travel. They have the potential to boost the industry by leveraging new emerging lighter-than-air (LTA) and heavier-than-air (HTA) technologies. Hybrid buoyant aircraft are possible substitutes for jet and turbo-propeller aircraft currently utilized in aviation, and this manuscript is a country-specific (Malaysia) analysis to determine their potential market, assessing the tourism, business, agricultural, and airport transfer needs of such vehicles. A political, economic, social, and technological factors (PEST) analysis was also conducted to determine the impact of PEST parameters on the development of buoyant aircraft and to assess all existing problems …

Computational Thermal-Hydraulics Modeling Of Twisted Tape Enabled High Heat Flux Components, Emily Buckman Clark

Doctoral Dissertations

The goal of this work was to perform a computational investigation into the thermalhydraulic performance of water-cooled, twisted tape enabled high heat flux components at fusion relevant conditions. Fusion energy is a promising option for future clean energy generation, but the community must overcome significant scientific and engineering challenges before meeting the goal of electricity generation. One such challenge is the high heat flux thermal management of components in fusion and plasma physics experiments. Plasma facing components in the magnetic confinement devices, such as ITER or W7-X, will be subjected to extreme heat loads on the order of 10-20 MW/m …

Software Requirements Specification For Lunar Icecube, Michael R. Glaser-Garbrick

Morehead State Theses and Dissertations

A thesis presented to the faculty of the College of Science at Morehead State University in partial fulfillment of the requirements for the Degree Master of Science by Michael R. Glaser-Garbrick on April 21, 2017.

Integrating Unmanned Aircraft Operations Into The National Airspace System, Benjamin Cook, Holly Hughes, Kyle Wilkerson, Allison Little

Discovery Day - Prescott

Unmanned Aircraft Systems (UAS) are expected to dominate the National Airspace System (NAS) in the near future. One particular barrier preventing the integration of unmanned aircraft into the NAS is the lack of standardized procedures for distinguishing and communicating with remote UAS operators. In preparation for adopting unmanned flight operations into a complex control system, it is important to identify solutions to effectively control UAS in the NAS. To achieve simultaneous safe manned and unmanned aircraft operations in the NAS, the Joint UAS and ATC Team (JUAT) at Embry-Riddle Aeronautical University (ERAU) are developing a system that could be used …

The Effect Of Biocomposite Material In A Composite Structure Under Compression Loading, Benjamin Andrew Sweeney

Master's Theses

While composite structures exhibit exceptional strength and weight saving possibilities for engineering applications, sometimes their overall cost and/or material performance can limit their usage when compared to conventional structural materials. Meanwhile ‘biocomposites’, composite structures consisting of natural fibers (i.e. bamboo fibers), display higher cost efficiency and unique structural benefits such as ‘sustainability’. This analysis will determine if the integration of these two different types of composites are beneficial to the overall structure. Specifically, the structure will consist of a one internal bamboo veneer biocomposite ply; and two external carbon fiber weave composite plies surrounding the bamboo biocomposite. To acquire results …