Open Access. Powered by Scholars. Published by Universities.®
Articles 1 - 5 of 5
Full-Text Articles in Aerospace Engineering
Additive Manufacturing Of Molybdenum For High Temperature Structural Applications, Megan L. Bustin
Additive Manufacturing Of Molybdenum For High Temperature Structural Applications, Megan L. Bustin
Theses and Dissertations
This research considered additive manufactured (AM) molybdenum (Mo) and the effect of three variables on microstructure, mechanical properties, and the relationship between the two. Test temperature, laser speed, and shield gas or build atmosphere were varied, and samples tested and analyzed using a three-point bending test, chemical composition, and optical and scanning electron microscopy. The relationship among variables and results using a Design of Experiments was limited compared to the inclusion of every tested sample. Most effects were expected: samples tested at room temperature were brittle without statistical significance; increasing laser speed resulted in decreased ductility and strain, smaller grain …
Structural Sizing Of Post-Buckled Thermally Stressed Stiffened Panels, Walid Arsalane
Structural Sizing Of Post-Buckled Thermally Stressed Stiffened Panels, Walid Arsalane
Theses and Dissertations
Design of thermoelastic structures can be highly counterintuitive due to design-dependent loading and impact of geometric nonlinearity on the structural response. Thermal loading generates in-plane stresses in a restrained panel, but the presence of geometric nonlinearity creates an extension-bending coupling that results in considerable transverse displacement and variation in stiffness characteristics, and these affects are enhanced in post-bucking regimes. Herein a methodology for structural sizing of thermally stressed post-buckled stiffened panels is proposed and applied for optimization of the blade and hat stiffeners using a gradient-based optimizer. The stiffened panels are subjected to uniform thermal loading and optimized for minimum …
Standards-Compatible Smoke Points For Mono- And Un- Substituted Cycloalkane Fuel Components, Adekunle Vincent Adeniyi
Standards-Compatible Smoke Points For Mono- And Un- Substituted Cycloalkane Fuel Components, Adekunle Vincent Adeniyi
Theses and Dissertations
Emissions from the aviation industry have increased significantly over the decades and may continue to pose an environmental threat. Accordingly, efforts are being made to replace conventional aviation fuels with more sustainable alternatives that can both reduce net CO2 emissions as well as reduce other pollutants (i.e., particulates). Conventional jet fuels include aromatic species, which have high sooting tendency. Therefore, to reduce particulate emissions, the fuel aromatics content must be reduced. Cycloalkanes have potential for replacing aromatics content in jet fuel but, compared to other broad classes of chemical species that make up conventional and alternative jet fuel, there is …
Effects Of A Nitrogen And Hydrogen Build Atmosphere On The Properties Of Additively Manufactured Tungsten, Dana C. Madsen
Effects Of A Nitrogen And Hydrogen Build Atmosphere On The Properties Of Additively Manufactured Tungsten, Dana C. Madsen
Theses and Dissertations
Additively manufactured tungsten was printed in pure nitrogen, nitrogen-2.5% hydrogen, and nitrogen-5% hydrogen atmospheres as part of a 2^3 full factorial designed experiment and subjected to room temperature and high-temperature three-point-bend testing, chemical analysis, hardness testing, and microstructural imaging techniques. The pure nitrogen specimens exhibited the highest strength and ductility at both high temperature and room temperature. Chemical analysis showed a 2-8x reduction in compositional oxygen relative to unprocessed powder. Hardness values for all samples was between 306.8 and 361.5 HV1. It is proposed that adding hydrogen into the build atmosphere reduced the available energy density for tungsten melting by …
Investigation Of Additively Manufactured Molybdenum-Tungsten-Rhenium Alloys, Randolph T. Abaya
Investigation Of Additively Manufactured Molybdenum-Tungsten-Rhenium Alloys, Randolph T. Abaya
Theses and Dissertations
The process of creating metal components through additive manufacturing is changing the way different industries can avoid the shortcomings of traditional metal production. Metals such as tungsten, molybdenum, and rhenium have many advantages for different applications, especially when alloyed together. In this study, an additively manufactured alloy containing 70% molybdenum, 25% tungsten, and 5% rhenium (70Mo-25W-5Re) is tested for its strength, ductility, hardness, and porosity. The 70Mo-25W-5Re alloy is printed through Laser Powder Bed Fusion (LPBF) under different conditions such as printing speed and printing atmosphere. Additionally, the effects of post printing heat treatment are conducted to understand the advantages …