Open Access. Powered by Scholars. Published by Universities.®
Articles 1 - 5 of 5
Full-Text Articles in Aerospace Engineering
Mechanical Design Of A Low-Cost Deployable Solar Panel Array For A 1-U Cubesat, Thomas Mcguire, Skye Leake, Michael Parsons, Michael Hirsch, Benjamin Kading, Jeremy Straub, David Whalen
Mechanical Design Of A Low-Cost Deployable Solar Panel Array For A 1-U Cubesat, Thomas Mcguire, Skye Leake, Michael Parsons, Michael Hirsch, Benjamin Kading, Jeremy Straub, David Whalen
Jeremy Straub
CubeSats are small spacecraft with a nominal size of 10 cm x 10 cm x 10 cm and a mass of 1.33 kg (though some launch providers are now supporting expanded mass levels). While the CubeSat form factor has reduced the time and cost of spacecraft development, the required resources are still beyond the grasp of many colleges and universities. The Open Prototype for Educational Nanosats (OPEN) concept aims to solve this problem. OPEN is an inexpensive modular CubeSat that can be produced with a parts budget of less than $5,000. The OpenOrbiter program is working to develop this set …
Open Prototype For Educational Nanosats Cubesat Structural Design, Benjamin Kading, Jeremy Straub, Ronald Marsh
Open Prototype For Educational Nanosats Cubesat Structural Design, Benjamin Kading, Jeremy Straub, Ronald Marsh
Jeremy Straub
CubeSats are a class of small satellites that have recently gained significant interest and are being developed and used for engineering test missions, bona fide research and various other applications. A 1-U CubeSat (the original form factor) has nominal dimensions of 10 cm x 10 cm x 10 cm and a mass of no more than 1.33 kg (however, some integrators are now consistently allowing higher mass levels). Due to their small size and the demonstrated ability to successfully use consumer-grade electronics in low-Earth orbit, CubeSats cost significantly less than larger sized satellites. These reduced costs, however, are still beyond …
Design And Development Of A Payload Area Sub-Structure For A 1-U Cubesat, Tristan Plante, Jordan Forbord, Alexander Holland, Landon Klein, Benjamin Kading, Jeremy Straub, Ronald Marsh
Design And Development Of A Payload Area Sub-Structure For A 1-U Cubesat, Tristan Plante, Jordan Forbord, Alexander Holland, Landon Klein, Benjamin Kading, Jeremy Straub, Ronald Marsh
Jeremy Straub
Advancements in the miniaturization of electronics and other factors have allowed CubeSats, small satellites that can be created at a much lower cost than a large satellite, to perform numerous useful tasks. CubeSats, which are nominally 10 cm x 10 cm x 10 cm with a mass of less than 1.33 kg, are also developed in academic institutions to aid student learning; however, the development and launch of CubeSats can be expensive. Because of this, the Open Prototype for Educational NanoSats (OPEN) aims to make CubeSat development more affordable by developing a set of design documents as well as the …
Openorbiter Mechanical Design: A New Approach To The Design Of A 1-U Cubesat, Benjamin Kading, Jeremy Straub, Ronald Marsh
Openorbiter Mechanical Design: A New Approach To The Design Of A 1-U Cubesat, Benjamin Kading, Jeremy Straub, Ronald Marsh
Jeremy Straub
The OpenOrbiter Small Spacecraft Development Initiative is working to create a set of designs and implementation instructions for a 1-U CubeSat, called the Open Prototype for Educational NanoSats. These designs target a total parts cost of below USD $5,000. This design will be made publically available to facilitate its use by others, with or without modification. A ‘side slotted’ CubeSat design (where main circuit boards are placed in slots between the rails on the outside) has been developed for OpenOrbiter. This paper discusses the design choices that were made during the mechanical structure development of the OpenOrbiter CubeSat design, required …
Mechanical Design And Analysis Of A 1-U Cubesat, Ben Kading, Jeremy Straub, Ronald Marsh
Mechanical Design And Analysis Of A 1-U Cubesat, Ben Kading, Jeremy Straub, Ronald Marsh
Jeremy Straub
The OpenOrbiter Small Spacecraft De-velopment Initiative seeks to create a low-cost, easy-to-assemble CubeSat1 design that can be produced with a parts budget of under USD$5,0002. In [1], an initial design was presented; this design was enhanced in [3] and has been revised further. The current design, which has switched focus from defining specifications, requirements and constraints to identifying real parts which meet these previously defined constraints, is presented herein.