Engineering Commons^™

Integrative Physiology-Coupled Pilot-Centered Flight Simulation, Shawn C. Harrison

Electrical & Computer Engineering Theses & Dissertations

Maintaining the pilot’s physiological performance envelope within the limits of human capabilities may be crucial for avoiding hazardous physiological episodes in fighter aircraft that compromise safety. The main physiological episode of interest is impaired pilot respiration, better known as hypoxia caused by a high fraction of inspired oxygen (FiO₂) at high altitudes and variation in accelerative gravitational forces (g-forces). Integrated into fighter aircraft is an Onboard Oxygen Generating System (OBOGS) developed to mitigate the necessity of gaseous and liquid oxygen cannisters [1]. OBOGS act as a life support in hypoxic environments by providing oxygen-rich air, thereby oxygenating the …

Overcoming Supply Disruptions During Pandemics By Utilizing Found Hardware For Open Source Gentle Ventilation, S. Oberloier, N. Gallup, J. M. Pearce

Michigan Tech Publications

This article details the design of an open source emergency gentle ventilator (gentle-vent) framework that can be used in periods of scarcity. Although it is not a medical device, the system utilizes a wide range of commonly-available components that are combined using basic electronics skills to achieve the desired performance. The main function of the gentle-vent is to generate a calibrated pressure wave at the pump to provide support to the patient's breathing. Each gentle-vent permutation was tested using a DIY manometer as it would be utilized in the field in low-resource settings and validated with an open source VentMon. …

Models And Optimal Controls For Smart Homes And Their Integration Into The Electric Power Grid, Huangjie Gong

Theses and Dissertations--Electrical and Computer Engineering

Smart homes can operate as a distributed energy resource (DER), when equipped with controllable high-efficiency appliances, solar photovoltaic (PV) generators, electric vehicles (EV) and energy storage systems (ESS). The high penetration of such buildings changes the typical electric power load profile, which without appropriate controls, may become a “duck curve” when the surplus PV generation is high, or a “dragon curve” when the EV charging load is high. A smart home may contribute to an optimal solution of such problems through the energy storage capacity, provided by its by battery energy storage system (BESS), heating, ventilation, and air conditioning (HVAC) …

Virtual Power Plant Control For Large Residential Communities Using Hvac Systems For Energy Storage, Huangjie Gong, Evan S. Jones, Rosemary E. Alden, Andrew G. Frye, Donald G. Colliver, Dan M. Ionel

Power and Energy Institute of Kentucky Faculty Publications

Heating, ventilation, and air-conditioning (HVAC) systems use the most electricity of any household appliance in residential communities. HVAC system modeling facilitates the study of demand response (DR) at both the residential and power system levels. In this article, the equivalent thermal model of a reference house is proposed. Parameters for the reference house were determined based on the systematic study of experimental data obtained from fully instrumented field demonstrators. Energy storage capacity of HVAC systems is calculated and an equivalent state-of-charge is defined. The uniformity between HVAC systems and battery energy storage system is demonstrated by DR control. The aggregated …

Generalized Energy Storage Model-In-The-Loop Suitable For Energy Star And Cta-2045 Control Types, Huangjie Gong, Evan S. Jones, A. H. M. Jakaria, Aminul Huque, Ajit Renjit, Dan M. Ionel

Power and Energy Institute of Kentucky Faculty Publications

The paper proposes a generalized energy storage (GES) model for battery energy storage systems (BESS), electric water heaters (EWH) and heating, ventilation, and air-conditioning (HVAC) systems. The analogies, including state of charge versus water temperature differential, are identified and explained, and models-in-the-loop (MIL) are introduced, which are compatible with the Energy Star and CTA-2045 general specifications and command types. Emphasis is placed on the proposed EWH model as it needfully fulfills a gap in present literature. The corresponding MIL has been implemented in the DER integration testbed, which was originally developed by EPRI, and satisfactorily validated against experimental results. A …

Power Factor And Reactive Power In Us Residences – Survey And Energyplus Modeling, Hope C. Anderson, Abdullah Al Hadi, Evan S. Jones, Dan M. Ionel

Power and Energy Institute of Kentucky Faculty Publications

Electric power systems are experiencing a growing number of electronic loads in the residential sector as modern appliance technology progresses, and it has become increasingly more important to consider the total power factor (PF) of residential communities. This paper provides a survey based on literature and publicly available information of typical appliance PF values and effects at the residential level as well as a discussion on appliance energy use and corresponding operation schedules. A procedure for the calculation of equivalent PF is proposed and exemplified with minutely experimental data at 15-minute and hourly time intervals, which correspond to smart metering …

Application Of Methods Of Intermittent Ventilation Of Industrial Premises Using A Digital Data Transmission System, Yuriy Shipulin, Abdullayev Temur, Jamolidin Usmanov, Shahnoza Ergasheva

Chemical Technology, Control and Management

The article is devoted to topical applied issues, the application of methods of intermittent ventilation of industrial buildings using a digital data transmission system. The requirements for the parameters of the environment are determined, which include: composition, purity, temperature, air humidity, the content of positive and negative ions, the presence of fields of various origins (thermal, optical, biological, gas, and electromagnetic). The authors of the article argue that some of the listed parameters can be supported by ventilation and air conditioning (SCA) systems.

It is shown that when the controlled parameters are limited to a multidimensional area, the SCA control …

Demand Response Of Hvacs In Large Residential Communities Based On Experimental Developments, Huangjie Gong, Evan S. Jones, Rosemary E. Alden, Andrew G. Frye, Donald G. Colliver, Dan M. Ionel

Power and Energy Institute of Kentucky Faculty Publications

Heating, ventilation, and air-conditioning (HVAC) systems contribute the largest electricity usage for a residential community. Modeling of the HVAC systems facilitate the study of demand response (DR) at both the residential and the power system level. In this paper, the equivalent thermal model of a reference house was proposed. Parameters for the reference house were determined based on the systematic study of experimental data obtained from fully instrumented field demonstrators. The aggregated HVAC load was modeled based on the reference house while considering a realistic distribution of HVAC parameters derived from data that was provided by one of the largest …

Partially Reprapable Automated Open Source Bag Valve Mask-Based Ventilator, Aliaksei Petsiuk, Nagendra G. Tanikella, Samantha Dertinger, Adam Pringle, Shane Oberloier, Joshua M. Pearce

Michigan Tech Publications

This study describes the development of a simple and easy-to-build portable automated bag valve mask (BVM) compression system, which, during acute shortages and supply chain disruptions can serve as a temporary emergency ventilator. The resuscitation system is based on the Arduino controller with a real-time operating system installed on a largely RepRap 3-D printable parametric component-based structure. The cost of the materials for the system is under $170, which makes it affordable for replication by makers around the world. The device provides a controlled breathing mode with tidal volumes from 100 to 800 mL, breathing rates from 5 to 40 …

The Effect Of High Efficiency Building Technologies And Pv Generation On The Energy Profiles For Typical Us Residences, Evan S. Jones, Rosemary E. Alden, Huangjie Gong, Andrew G. Frye, Donald G. Colliver, Dan M. Ionel

Power and Energy Institute of Kentucky Faculty Publications

The penetrations of high efficiency technologies and photovoltaic (PV) generation are increasing in the residential sector. Technologies such as improved insulation and efficient HVAC systems significantly affect the energy profile of a house. This effect varies due to climate characteristics, i.e. temperature, solar radiation, relative humidity, and wind speeds. The effect of other technologies, such as efficient water heaters, lighting, or kitchen appliances, is mainly governed by human behavior, which may be represented by a schedule. This paper studies the performance of both climate-influenced and scheduled household devices among different levels of efficiency through combined computational and experimental methods. Three …

Reprapable Automated Open Source Bag Valve Mask-Based Ventilator, Aliaksei Petsiuk, Nagendra Gautam Tanikella, Samantha C. Dertinger, Adam Pringle, Shane Oberloier, Joshua M. Pearce

Michigan Tech Publications

This study describes the development of an automated bag valve mask (BVM) compression system, which, during acute shortages and supply chain disruptions can serve as a temporary emergency ventilator. The resuscitation system is based on the Arduino controller with a real-time operating system installed on a largely RepRap 3-D printable parametric component-based structure. The cost of the system is under $170, which makes it affordable for replication by makers around the world. The device provides a controlled breathing mode with tidal volumes from 100 to 800 milliliters, breathing rates from 5 to 40 breaths/minute, and inspiratory-to-expiratory ratio from 1:1 to …

The Estimation And Control Of A Laboratory Heating And Ventilation System, Robin P. Mooney

Masters in Advanced Engineering

This dissertation is concerned with the estimation and control of a laboratory heating and ventilation system (Instrutek VVS-400). The system is a 2x2 multi-input multi-output process (MIMO). It has been shown that simple techniques such as the ultimate cycle method do not provide adequate control of the process. The system was interfaced with a PC using Matlab/Simulink via a data acquisition package (Humusoft). Continuous time process identification techniques were applied to the flow and temperature processes. The alternative tangent and point method was used to model the processes, and their interaction, using a first order lag plus delay model. Models …