Open Access. Powered by Scholars. Published by Universities.®
Articles 1 - 14 of 14
Full-Text Articles in Engineering
A Strong And Ductile Cobalt-Free Solid-Solution Fe30ni30mn30cr10 Multi-Principal Element Alloy From Hot Rolling, Hans Pommerenke, Jiaqi Duan, Nathan Curtis, Victor Delibera, Adam Bratten, Andrew Hoffman, Mario F. Buchely, Ronald J. O'Malley, Haiming Wen
A Strong And Ductile Cobalt-Free Solid-Solution Fe30ni30mn30cr10 Multi-Principal Element Alloy From Hot Rolling, Hans Pommerenke, Jiaqi Duan, Nathan Curtis, Victor Delibera, Adam Bratten, Andrew Hoffman, Mario F. Buchely, Ronald J. O'Malley, Haiming Wen
Materials Science and Engineering Faculty Research & Creative Works
Most of the Face-Centered Cubic (FCC) Multi-Principal Element Alloys (MPEAs) Developed Thus Far Contain Cobalt. for Many Applications, it is Either required or Beneficial to Avoid Cobalt, Since Cobalt Has Long-Term Activation Issue (For Nuclear Applications), is Expensive, and is Considered a Critical Material. in Addition, FCC Structured Solid-Solution MPEAs Tend to Have Relatively Low Strength. a FCC Solid-Solution Fe30Ni30Mn30Cr10 (At %) MPEA Was Fabricated Via Arc Melting, Followed by Homogenization at 1100 °C for 12 H. the Alloy Was Hot Rolled at 1100 °C with a Total Reduction of Up to 97 %. the Microstructure Was Characterized and Mechanical …
Mechanical Properties Of Zrb2 Ceramics Determined By Two Laboratories, Jeffrey J. Swab, Jecee Jarman, William Fahrenholtz, Jeremy Lee Watts
Mechanical Properties Of Zrb2 Ceramics Determined By Two Laboratories, Jeffrey J. Swab, Jecee Jarman, William Fahrenholtz, Jeremy Lee Watts
Materials Science and Engineering Faculty Research & Creative Works
The mechanical properties for zirconium diboride (ZrB2) were measured at two laboratories and compared. Two billets of ZrB2 were prepared by hot-pressing commercial powder. The relative densities of the billets were >99% and with an average grain size of 5.9 ± 4.5 µm. Both laboratories prepared American Society for Testing and Materials (ASTM) C1161 B-bars for strength and ASTM C1421 bars with notch configuration A for fracture toughness. Specimens were machined by diamond grinding at the Army Research Laboratory (ARL) and electrical discharge machining (EDM) at Missouri S&T. Strength bars tested at Missouri S&T were polished to a.25 μm finish …
Effect Of Mechanical Activation On Carbothermal Synthesis And Densification Of Zrc, Nina Obradović, Lun Feng, Suzana Filipović, Miljana Mirković, Darko Kosanović, Jelena Rogan, William Fahrenholtz
Effect Of Mechanical Activation On Carbothermal Synthesis And Densification Of Zrc, Nina Obradović, Lun Feng, Suzana Filipović, Miljana Mirković, Darko Kosanović, Jelena Rogan, William Fahrenholtz
Materials Science and Engineering Faculty Research & Creative Works
Zirconium carbide ceramics were prepared by carbothermal reduction of ZrO2 and C that were mixed by high-energy ball milling. Powders were milled for times from 0 to 120 min in air. As milling time increased, the surface area of the powders increased, indicating significant particle size reduction. Milled powders were reacted at 1600 °C and then densified by spark plasma sintering at 2000 °C, which was sufficient to convert the starting powders to zirconium carbide. Unmilled powders did not reach full density. Milled powders reached full density, but ZrO2 impurities were found for specimens prepared from powders milled …
Strength Retention Of Single-Phase High-Entropy Diboride Ceramics Up To 2000°C, Lun Feng, William Fahrenholtz, Gregory E. Hilmas, Yue Zhou, Jincheng Bai
Strength Retention Of Single-Phase High-Entropy Diboride Ceramics Up To 2000°C, Lun Feng, William Fahrenholtz, Gregory E. Hilmas, Yue Zhou, Jincheng Bai
Materials Science and Engineering Faculty Research & Creative Works
The mechanical properties of single-phase (Hf0.2,Nb0.2,Ta0.2,Ti0.2,Zr0.2)B2 ceramics with high purity were investigated. The resulting ceramics had relative density greater than 99%, and an average grain size of 4.3 ± 1.6 μm. At room temperature (RT), the Vickers hardness was 25.2 ± 0.6 GPa at a load of 0.49 N, Young's modulus was 551 ± 7 GPa, fracture toughness was 4.5 ± 0.4 MPa m1/2, and flexural strength was 507 ± 10 MPa. Flexural strength increased by more than 50% from 507 ± 10 MPa at RT to 776 ± …
Processing And Mechanical Properties Of Hot-Pressed Zirconium Diboride – Zirconium Carbide Ceramics, Eric W. Neuman, William Fahrenholtz, Gregory E. Hilmas
Processing And Mechanical Properties Of Hot-Pressed Zirconium Diboride – Zirconium Carbide Ceramics, Eric W. Neuman, William Fahrenholtz, Gregory E. Hilmas
Materials Science and Engineering Faculty Research & Creative Works
ZrB2 was mixed with 0.5 wt% carbon and up to 10 vol% ZrC and densified by hot-pressing at 2000 °C. All compositions were > 99.8% dense following hot-pressing. The dense ceramics contained 1–1.5 vol% less ZrC than the nominal ZrC addition and had between 0.5 and 1 vol% residual carbon. Grain sizes for the ZrB2 phase decreased from 10.1 µm for 2.5 vol% ZrC to 4.2 µm for 10 vol% ZrC, while the ZrC cluster size increased from 1.3 µm to 2.2 µm over the same composition range. Elastic modulus was ~505 GPa and toughness was ~2.6 MPa·m½ for all compositions. …
Effect Of Boron In Cast Iron, Suyash Durendra Pawaskar
Effect Of Boron In Cast Iron, Suyash Durendra Pawaskar
Masters Theses
"Boron, mostly considered a residual element, has started to cause issues in the cast iron foundries by causing a decrease in the strength of pearlitic gray and ductile iron castings. Because of the increase in the use of boron-added steel scrap from automotive steel and a lack of agreement on the critical levels of boron in cast iron, foundries are facing difficulties in controlling the microstructure of gray iron castings when boron is present. The current investigation was designed to analyze the effects of boron in cast irons and predict a mechanism to understand its effects with a vision of …
Room-Temperature Mechanical Properties Of A High-Entropy Diboride, Alec C. Murchie, Jeremy Lee Watts, William Fahrenholtz, Gregory E. Hilmas
Room-Temperature Mechanical Properties Of A High-Entropy Diboride, Alec C. Murchie, Jeremy Lee Watts, William Fahrenholtz, Gregory E. Hilmas
Materials Science and Engineering Faculty Research & Creative Works
The mechanical properties of a (Hf,Mo,Nb,Ta,W,Zr)B2 high-entropy ceramic were measured at room temperature. A two-step synthesis process was utilized to produce the (Hf,Mo,Nb,Ta,W,Zr)B2 ceramics. The process consisted of a boro/carbothermal reduction reaction followed by solid solution formation and densification through spark plasma sintering. Nominally, phase pure (Hf,Mo,Nb,Ta,W,Zr)B2 was sintered to near full density (8.98 g/cm3) at 2000°C. The mean grain size was 6 ± 2 µm with a maximum grain size of 17 µm. Flexural strength was 528 ± 53 MPa, Young's modulus was 520 ± 12 GPa, fracture toughness was 3.9 ± 1.2 MPa·m1/2, and hardness (HV0.2) was 33.1 …
Development Of Stage-I Tempered High Strength Cast Steel For Ground Engaging Tools, Viraj Ashok Athavale
Development Of Stage-I Tempered High Strength Cast Steel For Ground Engaging Tools, Viraj Ashok Athavale
Doctoral Dissertations
"Ground Engaging Tools (GET) are the expendable replacement parts used in heavy machinery used with mining or construction equipment. GET’s protect the expensive machine components from the wear and tear found common in high-impact or high-abrasion environments. The goal of this project is to develop advanced next-generation alloy choices that outperforms the existing GET materials. A method of predicting tempered hardness of mixed microstructures was formulated. Using this model, two alloy series viz. Cr-Ni-Mo and Mn-Si-Mo-V were proposed and experimented with the goal of obtaining a high strength and impact resistant cast steel. Cast iterations of Cr-Ni-Mo alloy series were …
An Investigation Of The Effect Of Direct Metal Deposition Parameters On The Characteristics Of The Deposited Layers, Tarak A. Amine, Joseph William Newkirk, Frank W. Liou
An Investigation Of The Effect Of Direct Metal Deposition Parameters On The Characteristics Of The Deposited Layers, Tarak A. Amine, Joseph William Newkirk, Frank W. Liou
Materials Science and Engineering Faculty Research & Creative Works
Multilayer direct laser deposition (DLD) is a fabrication process through which parts are fabricated by creating a molten pool into which metal powder is injected as particles. During fabrication, complex thermal activity occurs in different regions of the build; for example, newly deposited layers will reheat previously deposited layers. The objective of this study was to provide insight into the thermal activity that occurs during the DLD process. This work focused on the effect of the laser parameters of newly deposited layers on the microstructure and mechanical properties of the previously deposited layers in order to characterize these effects to …
Effect Of Architecture And Porosity On Mechanical Properties Of Borate Glass Scaffolds Made By Selective Laser Sintering, Krishna C. R. Kolan, Ming-Chuan Leu, Greg Hilmas, Taylor Comte
Effect Of Architecture And Porosity On Mechanical Properties Of Borate Glass Scaffolds Made By Selective Laser Sintering, Krishna C. R. Kolan, Ming-Chuan Leu, Greg Hilmas, Taylor Comte
Mechanical and Aerospace Engineering Faculty Research & Creative Works
The porosity and architecture of bone scaffolds, intended for use in bone repair or replacement, are two of the most important parameters in the field of bone tissue engineering. The two parameters not only affect the mechanical properties of the scaffolds but also aid in determining the amount of bone regeneration after implantation. Scaffolds with five different architectures and four porosity levels were fabricated using borate bioactive glass (13-93B3) using the selective laser sintering (SLS) process. The pore size of the scaffolds varied from 400 to 1300 μm. The compressive strength of the scaffolds varied from 1.7 to 15.5 MPa …
Freeze-Form Extrusion Fabrication Of Functionally Graded Material Composites Using Zirconium Carbide And Tungsten, Ang Li, Aaron S. Thornton, Bradley K. Deuser, Jeremy Lee Watts, Ming-Chuan Leu, Greg Hilmas, Robert G. Landers
Freeze-Form Extrusion Fabrication Of Functionally Graded Material Composites Using Zirconium Carbide And Tungsten, Ang Li, Aaron S. Thornton, Bradley K. Deuser, Jeremy Lee Watts, Ming-Chuan Leu, Greg Hilmas, Robert G. Landers
Materials Science and Engineering Faculty Research & Creative Works
Ultra-high-temperature ceramics are being investigated for future use in aerospace applications due to their superior thermo-mechanical properties, as well as their oxidation resistance, at temperatures above 2000⁰C. However, their brittleness makes them susceptible to thermal shock failure. As graded composites, components fabricated as functionally-graded materials (FGMs) can combine the superior properties of ceramics with the toughness of an underlying refractory metal. This paper discusses the grading of two materials through the use of a Freeze-form Extrusion Fabrication (FEF) system to build FGM parts consisting of zirconium carbide (ZrC) and tungsten (W). Aqueous-based colloidal suspensions of ZrC and W were developed …
Effect Of Particle Size, Binder Content And Heat Treatment On Mechanical Properties Of 13-93 Bioactive Glass Scaffolds, Krishna C. R. Kolan, Ming-Chuan Leu, Greg Hilmas, Mariano Garcia Velez
Effect Of Particle Size, Binder Content And Heat Treatment On Mechanical Properties Of 13-93 Bioactive Glass Scaffolds, Krishna C. R. Kolan, Ming-Chuan Leu, Greg Hilmas, Mariano Garcia Velez
Mechanical and Aerospace Engineering Faculty Research & Creative Works
Particle size, binder content and the post-processing schedule are important parameters that affect the microstructure, and, hence, the mechanical properties of parts produced using the indirect selective laser sintering process. 13-93 bioactive glass, with mean particle sizes ranging from 10 μm to 44 μm, is mixed with different amounts of stearic acid binder to fabricate green scaffolds. Through the design of the post-processing schedule, the time required for postprocessing the green scaffolds is reduced from the initial 80 hrs to 12 hrs. The compressive strength varies from 41 MPa for a part with~60% porosity to 157 MPa for a part …
Freeze Extrusion Fabrication Of 13-93 Bioactive Glass Scaffolds For Bone Repair, Tieshu Huang, Nikhil D. Doiphode, M. N. Rahaman, Ming-Chuan Leu, B. Sonny Bal, D. E. Day
Freeze Extrusion Fabrication Of 13-93 Bioactive Glass Scaffolds For Bone Repair, Tieshu Huang, Nikhil D. Doiphode, M. N. Rahaman, Ming-Chuan Leu, B. Sonny Bal, D. E. Day
Materials Science and Engineering Faculty Research & Creative Works
There is an increasing demand for synthetic scaffolds with the requisite biocompatibility, internal architecture, and mechanical properties for the bone repair and regeneration. In this work, scaffolds of a silicate bioactive glass (13-93) were prepared by a freeze extrusion fabrication (FEF) method and evaluated in vitro for potential applications in bone repair and regeneration. The process parameters for FEF production of scaffolds with the requisite microstructural characteristics, as well as the mechanical and cell culture response of the scaffolds were evaluated. After binder burnout and sintering (60 min at 700°C), the scaffolds consisted of a dense glass network with interpenetrating …
Freeform Fabrication Of Zirconium Diboride Parts Using Selective Laser Sintering, Ming-Chuan Leu, Erik B. Adamek, Tieshu Huang, Greg Hilmas, Fatih Dogan
Freeform Fabrication Of Zirconium Diboride Parts Using Selective Laser Sintering, Ming-Chuan Leu, Erik B. Adamek, Tieshu Huang, Greg Hilmas, Fatih Dogan
Mechanical and Aerospace Engineering Faculty Research & Creative Works
Using the Selective Laser Sintering (SLS) process, both flexural test bars and 3D fuel injector components have been fabricated with zirconium diboride (ZrB2) powder. Stearic acid was selected as the binder. Values of SLS process parameters were chosen such that the green parts could be built with sharp geometrical features and that the sintered parts could have good mechanical properties. After binder burnout and sintering, the SLS fabricated ZrB2 test bars achieved 80% theoretical density, and the average flexural strength of the sintered samples was 195 MPa. These values demonstrate the feasibility of the SLS process for …