Engineering Commons^™

Adsorption-Type Aluminium-Based Direct Lithium Extraction: The Effect Of Heat, Salinity And Lithium Content, Yasaman Boroumand, Amir Razmjou

Research outputs 2022 to 2026

Conventional lithium production through solar evaporation is considered a time-consuming procedure, taking a substantial 12 to 18 months with significant environmental impacts such as aquifer depletion and damaging the basin's complex hydrological system. Direct Lithium Extraction (DLE) has emerged as a promising alternative for lithium extraction from brines, offering reduced environmental impact. Although adsorption-type DLE with aluminium-based adsorbents is the sole commercial technology of DLE, a debate persists concerning its Technology Readiness Level (TRL), which challenges the prevailing notion that adsorption-type DLE undeniably reaches a TRL of 9. Within this narrative, we propose that adsorption is capable of attaining its …

Energy Efficiency In Additive Manufacturing: Condensed Review, Ismail Fidan, Vivekanand Naikwadi, Suhas Alkunte, Roshan Mishra, Khalid Tantawi

Engineering Technology Faculty Publications

Today, it is significant that the use of additive manufacturing (AM) has growing in almost every aspect of the daily life. A high number of sectors are adapting and implementing this revolutionary production technology in their domain to increase production volumes, reduce the cost of production, fabricate light weight and complex parts in a short period of time, and respond to the manufacturing needs of customers. It is clear that the AM technologies consume energy to complete the production tasks of each part. Therefore, it is imperative to know the impact of energy efficiency in order to economically and properly …

The Algorithm For The Design Of Fine Granular Substances’ Smart-Type Heat And Moisture Converters Based On Their Accuracy And Speed Criteria, Erkin Uljaev, Ali Abduakhatovich Abduraxmanov

Chemical Technology, Control and Management

The paper describes a technique and algorithm allowing to perform parametric design of smart-type heat and moisture converters (hereinafter SHMC) of fine-grained dispersive materials based on their criteria of accuracy and speed. The proposed algorithm optimizes the process of design of smart-type switches and ensure optimal performance of the switches. The method of calculation and selection of optimal parameters of smart-type heat and moisture converters intended to be used in the measurement of parameters such as heat and humidity of fine dispersive substances are aimed at boosting two parameters, i.e., the accuracy and speed. Also, the design stages have been …

Numerical Simulation Of The Donor-Assisted Stir Material For Friction Stir Welding Of Aluminum Alloys And Carbon Steel, Joseph Maniscalco, Abdelmageed A. Elmustafa, Srinivasa Bhukya, Zhenhua Wu

Mechanical & Aerospace Engineering Faculty Publications

In this research effort, we explore the use of a donor material to help heat workpieces without wearing the tool or adding more heat than necessary to the system. The donor material would typically be a small piece (or pieces) of material, presumably of lower strength than the workpiece but with a comparable melting point. The donor, a sandwich material, is positioned between the tool head and the material to be welded, where the tool initially plunges and heats up in the same manner as the parent material that is intended for welding. The donor material heats up subsequent to …

Artificial Neural Network For Predicting Heat Transfer Rates In Supercritical Carbon Dioxide, Vinusha Dasarla Giri Babu

Doctoral Dissertations and Master's Theses

Supercritical carbon dioxide as a working fluid in a closed Brayton cycle is proving to be more efficient than a conventional steam-based Rankine engine. Understanding the heat transfer properties of supercritical fluids is important for the design of a working engine cycle. The thermophysical properties of supercritical fluids tend to vary non-linearly near the pseudo-critical region. Traditionally, empirical correlations are used to calculate the heat transfer coefficient. It has been shown in the literature and within our own studies that these correlations provide inaccurate predictions near the pseudo-critical line, where heat transfer may be deteriorated or enhanced, resulting from strong …

Numerical Investigation Of Heat Generation And Accumulation Contributing To Elevated Temperature In Msw Landfills, Alborz Fathinezhad

LSU Doctoral Dissertations

Landfills are complex geostructures which contains organic and inorganic municipal, and in some cases industrial, wastes and are expected to remain operational for long times. Due to the complex nature of physical, chemical, biological, and thermal reactions that carry on within the depths of a landfill, unexpected incidents such as elevated temperatures could become inevitable. While uncommon to happen, elevated temperatures cause health and environmental issues such as odors, rapid settlements, slope instabilities. In addition, elevated temperatures can negatively impact engineered components in composite bottom liners, cover systems, leachate collection, and gas extraction and recovery systems.

Air intrusion into municipal …

High-Throughput Computation Of Interfacial Thermal Management Of Wide-Bandgap Semiconductors, Hao-Wen Chen

Theses and Dissertations

As semiconductor electronics, in particular high electron mobility transistors, get hot in operation, people are trying to incorporate different semiconductor materials to solve the problem of heat dissipation to maintain the device efficiency and performance. In this master thesis, two different packages, LAMMPS and almaBTE, that are focusing on micro-scale and atomic scale respectively, are used to simulate the heat transfer process across interfaces in two different scales. In the LAMMPS simulation, the research is exploring how the location of atoms and the thickness of interfacial layers will influence the interfacial thermal conductance. On the other hand, using the almaBTE …

Tokamak 3d Heat Load Investigations Using An Integrated Simulation Framework, Thomas Looby

Doctoral Dissertations

Reactor class nuclear fusion tokamaks will be inherently complex. Thousands of interconnected systems that span orders of magnitude in physical scale must operate cohesively for the machine to function. Because these reactor class tokamaks are all in an early design stage, it is difficult to quantify exactly how each subsystem will act within the context of the greater systems. Therefore, to predict the engineering parameters necessary to design the machine, simulation frameworks that can model individual systems as well as the interfaced systems are necessary. This dissertation outlines a novel framework developed to couple otherwise disparate computational domains together into …

Hybrid Phase-Change Lattice Boltzmann Simulation Of Vapor Condensation On Vertical Subcooled Walls, Wandong Zhao, Yuan Gao, Ruijie Li, Songgang Qiu, Yin Zhang, Ben Xu

Mechanical Engineering Faculty Publications and Presentations

Saturated vapor condensation on homogenous and heterogeneous subcooled walls is presented in this study by adopting a hybrid phase-change multiple-relaxation-time Lattice Boltzmann model. The effects of wall wettability on the condensation process, including droplets’ growth, coalescence and falling, and the influence of vapor flow to condensation are investigated. The results demonstrate that the heat fluxes around the triple-phase contact lines are higher than that in other cold areas in homogeneous subcooled walls, which actually indicates the fact that filmwise condensation is preventing the continuous condensation process. Furthermore, the dropwise condensation can be formed more easily on the heterogeneous surface with …

Lasers And Their Application In Heating Technology, Khalmanov A., Aymatov R., Omonkulov O., Khudaykulov A.

Problems of Architecture and Construction

Heat engineering is one of the common technical subjects that are important for heat engineering, such as heat generation by radiation, light transmission by optical lubricants, and the use of transmitted light energy. Currently, the laser is a powerful light-emitting diet and is based on the radiation generated by the electron transport of a layer of atomic energy.In article, a heat exchanger is considered in the high-temperature region and the laser radiation in heaters exceeds other heat exchange intensities.

Pool Boiling Heat Transfer To Cuo-H2o Nanofluid On Finned Surfaces, Zhixiong Li, M Sarafraz, Arash Mazinani, Tasawar Hayat, Hamed Alsulami, Marjan Goodarzi

Faculty of Engineering and Information Sciences - Papers: Part B

© 2020 Elsevier Ltd In the present research, the general aim is to understand further the potential effect of the surface shape and geometrical specification of rectangular parallel fins developed on the surface on the heat transfer coefficient, bubble formation, and fouling of the nanoparticles. To achieve this, the boiling thermal performance of the copper oxide nano-suspension (NS) was quantified on the modified surfaces with different geometrical specifications, including the width and height of the fins and space between fins. Results showed that the designed fins reduce the rate of the fouling of the nanoparticles on the boiling surface such …

Design Of X-Ray Source For Real-Time Computed Tomography, Wesley William Tucker

Doctoral Dissertations

"The reduction of motion blur in computed tomography (CT) drives the current research for multisource CT. Due to their compact nature, the current multisource systems utilize stationary angled anodes. Unfortunately, these configurations neither simplify the imaging geometry, nor satisfy the need for managing the high thermal loads demanded by real-time CT (30 acquisition frames per second). To add to the current field of knowledge, two x-ray tube concepts are presented in this dissertation. First, a simulation of transient thermal analysis was performed on a compact transmission-type x-ray tube anode operating in pulse-mode. A correlation was found between deposited beam power …

Enhanced Heat Transfer In Spray Cooling Through Surface Modifications: An Experimental And Computational Study, Azzam Saadi Salman

Theses and Dissertations

Today, dissipating high heat flux safely is one of the greatest challenges for thermal engineers in thermal management systems, and it becomes a critical barrier to technological developments for many engineering applications. Due to technological advances and aggressive micro-miniaturization of electronic components, the surface area of most devices has shrunk while the computational power increased exponentially. Therefore, the amount of heat dissipated from surfaces has increased significantly. Numerous cooling techniques have been introduced to replace the traditional air cooling systems and to maintain the efficiency and reliability of electronic components. Microelectronics work efficiently and safely at surface temperatures of < 100 ℃ and 125 ℃ for general and defense applications, respectively. One of the proposed alternative schemes is spray cooling, which is considered one of the most advanced cooling methods. It is used for high and ultra-high heat flux dissipation, as it can dissipate 150-200 W/cm2 while maintaining the surface temperature within this range. Also, spray cooling removes a large amount of energy at a lower liquid flow rate compared to other cooling techniques, such as jet impingement and microchannel heat sink. The thermal performance of spray cooling systems can be enhanced either actively or passively. Active enhancement is a very efficient technique; however, it adds more pumping power. The present work focuses on three main objectives: evaluating and analyzing spray cooling performance, developing a three-dimensional numerical multi-phase model for heat transfer process in spray cooling and enhancing the thermal performance of spray cooling passively.

First, …

Development Of Scalable And Tunable Super- Hydrophilic And - Hydrophobic Coatings On The Cu Substrate For Phase Change Heat Transfer Applications, Raikan Saad Dawas

Theses and Dissertations

The aim of this study is to enhance and sustain the thin liquid film evaporation (TLFE) as well as dropwise condensation (DWC) on scalable copper substrates. The current dissertation consists of two sections. The objective of the first section is to enhance the dry cooling technology which is widely used in industrial applications such as in the air side of power plants, AC unit, or electronic cooling. However, the thermal dissipation performance is limited with low heat transfer coefficients (HTCs) due to the low thermal conductivity and density of the air. Inspired by the phase change heat transfer during the …

Study On Performance Evaluation Of Co2 Heat Pump System Integrated With Thermal Energy Storage For Space Heating, Zhihua Wang, Yuxin Zheng, Fenghao Wang, Mengjie Song, Zhenjun Ma

Faculty of Engineering and Information Sciences - Papers: Part B

CO2 heat pumps have drawn a great deal of attention owing to their advantages of high efficiency and environmental friendly for heating water under low ambient temperature. However, the system performance is not desirable and shows a lower COP for space heating, especially for a radiator as heating terminal, due to the higher inlet water temperature at the gas cooler, which causes a large throttle loss when the refrigerant flow through the throttling device. To tackle this issue, a transcritical CO2 heat pump system integrated with thermal energy storage (TES) systems was developed in this paper. The heating performance of …

A Novel Empirical Heat Transfer Model For A Solar Thermal Storage Process Using Phase Change Materials, Yu Bie, Ming Li, Fei Chen, Grzegorz Krolczyk, Lin Yang, Zhixiong Li, Weihua Li

Faculty of Engineering and Information Sciences - Papers: Part B

Numerical and experimental analyses are often used to evaluate the solar thermal system with latent heat thermal energy storage (LHTES). However, the relationship between the numerical simulation and actual heat transfer process is still unclear. This work compares the simulated average temperature of two different phase change materials (PCMs) with experimental result at different operation conditions for the purpose of developing a temperature correction model. A novel empirical heat transfer model is then established to improve the simulation accuracy of PCM-based solar thermal systems. The contributions of this work include that (1) the system performance could be evaluated by the …

Optimization Of Analytical Inverse Heat Transfer Recovery Solution, Nathan Schick

Masters Theses

This thesis describes the different methods used when trying to solve inverse heat transfer problems, particularly those involving recovering heat flux. There are currently several techniques to measure the temperature history in an object subjected to heat transfer using various temperature sensors, however these types of sensors are gradually being replaced by Temperature Sensitive Paints (TSP), a technique that is more accurate and provides a better spatial resolution. TSP is a polymer that is applied on a base object. Changes in temperature in the polymer result in variations of the luminescence intensity in the paint. These variations can be captured …

The Dependence Of Heat Transfer Resistance Of Many Corrugated Small Foam Blocks On The Number And Dimensions Of Hollows, G. Shukurov, B. Turaboyev, Sh. Musayev

Problems of Architecture and Construction

In paper results of theoretical heat-physical researches are resulted and dependences of resistance to a heat transfer of the small block from foam concrete from quantity of through hollows, the form of their arrangement and from their sizes in the block are defined. Besides it is offered the empirical formula for definition of resistance of a heat transfer of the small block from foam concrete depending on quantity of through hollows.

Heat-Physical Calculation Of Constructions Of Building Foundations According To The Requirements Of Heat Protect Rate Of Buildings, E. Tulakov, Sh. Sirojiddinov

Problems of Architecture and Construction

Quite often, the foundations are combined with the walls of basements. Their reliable operation can be ensured only in the presence of thermal insulation of external structures in contact with the ground. The need for insulation is due to the fact that heat loss through the underground part of the building in some cases up to 20% of the total heat loss. In the presence of a heated basement, insulation will protect the walls of the basement from freezing, will help prevent condensation, dampness and mold development.

Impact Of Hysteresis Heating Of Railroad Bearing Thermoplastic Elastomer Suspension Pad On Railroad Bearing Thermal Management, Oscar O. Rodriguez, Arturo A. Fuentes, Constantine Tarawneh

Mechanical Engineering Faculty Publications and Presentations

It is a known fact that polymers and all other materials develop hysteresis heating due to the viscoelastic response or internal friction. The hysteresis or phase lag occurs when cyclic loading is applied leading to the dissipation of mechanical energy. The hysteresis heating is induced by the internal heat generation of the material, which occurs at the molecular level as it is being disturbed cyclically. Understanding the hysteresis heating of the railroad bearing elastomer suspension element during operation is essential to predict its dynamic response and structural integrity, as well as to predict the thermal behavior of the railroad bearing …

Thermoelectrics And Thermoelectric Devices, Benjamin T. Erck

Senior Theses

The field of thermoelectrics has many applications, and more are found in everyday systems. From its current studies, it is apparent that improving the figure of merit zT (which defines a good thermoelectric material) is important in the effectiveness of power generation. Another important part of thermoelectrics is the duality of these devices. They can both move heat and generate power, depending on their role in the system. In this thesis research, a process was made to test these thermoelectric relationships for a few Peltier devices in order to understand their efficiencies and what systems they can be applied to.

Red Hot: Researchers Develop Imaging Test For Glowing Rocket Engines | College Of Engineering, Usu College Of Engineering

College of Engineering News

Researchers at Utah State University are learning more about how extreme temperatures affect the structural integrity of rocket engines.

Experimental Performance Analysis And Evaluation Of A Novel Frost-Free Air Source Heat Pump System, Zhihua Wang, Fenghao Wang, Zhenjun Ma, Mengjie Song, Wenke Fan

Faculty of Engineering and Information Sciences - Papers: Part B

To tackle the problem of frosting occurred on the outdoor coil surface when an air source heat pump (ASHP) is operated in winter, a novel frost-free ASHP system has been developed. However, the dehumidification performance and the frost-free time of the system operated are highly dependent on the electronic expansion valve (EEV) opening of the 1st stage throttle. In addition, the coefficient of performance (COP) of the systems is controlled by the EEV opening of the 2nd stage throttle. Therefore, the objective of this study is to investigate the effect of the EEV opening on the system thermodynamic performance in …

Formulation Of A Model Predictive Control Algorithm To Enhance The Performance Of A Latent Heat Solar Thermal System, Gianluca Serale, Massimo Fiorentini, Alfonso Capozzoli, Paul Cooper, Marco Perino

Faculty of Engineering and Information Sciences - Papers: Part B

Model predictive control has proved to be a promising control strategy for improving the operational performance of multi-source thermal energy generation systems with the aim of maximising the exploitation of on-site renewable resources. This paper presents the formulation and implementation of a model predictive control strategy for the management of a latent heat thermal energy storage unit coupled with a solar thermal collector and a backup electric heater. The system uses an innovative Phase Change Material slurry for both the heat transfer fluid and storage media. The formulation of a model predictive controller of such a closed-loop solar system is …

Electrical Response Of Thermoelectric Generator To Geometry Variation Under Transient Thermal Boundary Condition, Elias Yazdanshenas, Alireza Rezania, Meysam Karami Rad, Lasse Rosendahl

Mechanical & Aerospace Engineering Faculty Publications

A three-dimensional numerical model is applied in this study to illustrate the electrical response of a thermoelectric generator (TEG) during transient heat flux at the hot side. In this work, various types of thermal boundary conditions are considered to evaluate the performance of the TEG. Thus, a TEG under pulsed heat flux is studied numerically, and the numerical model is verified by experimental results. With the consideration of a defined reference geometry, different heat flux frequencies are applied in order to evaluate the corresponding electrical output by the TEG. In addition, variation of the module performance for various TEG leg …

An Autothermal, Representative Scale Test Of Compost Heat Potential Using Geostatistical Analysis, William J. Mccune-Sanders

Graduate College Dissertations and Theses

Composting has been practiced for thousands of years as a way of stabilizing and recycling organic matter into useful soil amendments. Thermophilic compost releases significant amounts of heat at temperatures (~140 °F) that are useful for environmental heating or process water. This heat has been taken advantage of in various ways throughout history, but development of a widely adopted technology remains elusive.

The biggest barrier to adoption of compost heat recovery (CHR) systems is projecting accurate, attractive economic returns. The cost of transfer equipment is significant, and with variability in composting substrates and methods, it is difficult to predict the …

Sf6 Gas-Insulated 50-Kva Distribution Transformer Design, Okan Özgönenel, David Thomas, Ünal Kurt

Turkish Journal of Electrical Engineering and Computer Sciences

There are increasing environmental concerns such that governments are pressured to cooperate with international concurrences. One of the most harmful contaminants is mineral oil when it infiltrates the soil. Although it is a good material in the act of insulating in distribution/power transformers, it presents some environmental hazards and safety disadvantages. For this reason, gas-insulated transformers are considered particularly for hazardous locations. An oil-insulated distribution transformer of 50 kVA, 34.5/0.4 kV, and 50 Hz is investigated and converted to SF6 gas-insulated transformer in this study. The suggested distribution transformer model with SF6 insulated has many benefits, such as being explosion-proof …

Hysteresis Heating Of Railroad Bearing Thermoplastic Elastomer Suspension Element, Oscar O. Rodriguez, Arturo A. Fuentes, Constantine Tarawneh, Robert E. Jones

Mechanical Engineering Faculty Publications and Presentations

Thermoplastic elastomers (TPE’s) are increasingly being used in rail service in load damping applications. They are superior to traditional elastomers primarily in their ease of fabrication. Like traditional elastomers they offer benefits including reduction in noise emissions and improved wear resistance in metal components that are in contact with such parts in the railcar suspension system. However, viscoelastic materials, such as the railroad bearing thermoplastic elastomer suspension element (or elastomeric pad), are known to develop self-heating (hysteresis) under cyclic loading, which can lead to undesirable consequences. Quantifying the hysteresis heating of the pad during operation is therefore essential to predict …

Joe On The Go, Nico Ledwith, Grayson Meurrens

Computer Engineering

The ultimate goal for this project is to design an automatic, large capacity coffee maker. The system should be able to detect when a cup or mug is in position to receive coffee, then dispense a cup’s worth (~ 8oz) of coffee. When the coffee in the urn is getting low, our system should be able to allow a person to put new coffee grounds in the top, then push a button to start the coffee brewing process. More specifically, we had to accomplish the following tasks in order to meet our goals: solving the issue of transporting water from …

Instant Hot Water Heater, Hunter Arnold

All Undergraduate Projects

One of the first steps in the beer brewing process is to heat water to a specific temperature before it is mixed with the malt. The purpose of this project was to make a more compact and efficient heating device for the beer brewing process. The output temperature must be between 170⁰F and 180⁰F. The minimum flow rate should be half a gallon per minute with the maximum flow rate of three gallons per minute. The device will also need to mount to a collapsible beer rack being designed by Andrew Kastning. The device will be primarily compromised of two …