Engineering Commons^™

Self-Assembly Of Exfoliated Graphene Flakes As Anticorrosive Coatings For Additive Manufactured Steels, Kaleb Hood, Wen Qian, Yi Xia, Savannah Krupa, Annie Dao, Sarah Ahmed, Samuel Olson, Nam Nguyen, Joseph A. Turner, Jun Jiao

Department of Mechanical and Materials Engineering: Faculty Publications

This study demonstrates the feasibility of using liquid exfoliation of expandable graphite into multilayer exfoliated graphene flakes (EGFs) to form a self-assembled thin film on an air–water interface. The film can coat the surface of additive manufactured (AM) steel substrates to enhance surface properties, specifically AM 316 stainless-steel (AM316), AM 8620 steel (AM8620), and samples of the same alloys made by conventional manufacturing (CM) processes. Liquid exfoliation offers a high yield route for an EGF coating that can cover up to 95% of the sample surface with a single application. The thin, flexible EGFs can coat a rough AM metal …

The Study Of Corrosion On Additive-Manufactured Metals., Braydan Daniels

Electronic Theses and Dissertations

The purpose of this study was to investigate and compare the corrosion mechanisms between wrought and additive-manufactured (3D-printed) copper and stainless steel. The experimental procedure consisted of measuring the open circuit potential, electrochemical impedance spectroscopy, linear sweep voltammetry, Tafel analysis, surface topology, and scanning electron microscopy for each metal within salt water, tap water, sulfuric acid, and synthetic body fluid (excluding copper in synthetic body fluid).

Overall, printed stainless steel was more corrosion-resistant than wrought stainless steel in tap water and synthetic body fluid based on OCP, LSV, and surface topology results. Additionally, printed copper was more corrosion-resistant than wrought …

Near-Ir Laser Ablation Of Simulated Radiologically Contaminated Oxides On Carbon Steel Feeder Pipes, Thao Viet Do

Electronic Thesis and Dissertation Repository

As nuclear power plants age and retire from service, many countries face significant challenges concerning the safe long-term storage and disposal of large volumes of low and intermediate level radioactive wastes (L&ILW). The volumes of metallic waste are of particular concern, as when metal corrodes it produces hydrogen that could lead to pressure build-up in interim storage and disposal. In Canada, a significant fraction of the metallic wastes for Canada Deuterium Uranium (CANDU) nuclear reactors are out-of-core reactor components, such as carbon steel (CS) feeder pipes. The radioactive contamination is expected to be largely confined to the surface oxide layers …

An Investigation On The Interface Corrosion Behaviors Of Cobalt Interconnects In Chemical Mechanical Polishing Slurry, Kai-Xuan Qin, Peng-Fei Chang, Yu-Lin Huang, Ming Li, Tao Hang

Journal of Electrochemistry

Cobalt is widely regarded as the most promising interconnect material for 10 nm node and beyond. The development of a chemical mechanical planarization (CMP) slurry suitable for cobalt interconnect is a critical component for the application of cobalt interconnect. During CMP process of the interconnect layer, the achievement of high-quality surface after planarization is greatly challenged by the metal corrosion in CMP slurry. In this contribution, the corrosion behavior of cobalt in a slurry with potassium persulfate (KPS) as an oxidizer, glycine as a complexing agent, and benzotriazole (BTA) as an inhibitor was investigated. Static erosion rates (SER) of cobalt …

Electrochemical Response Of A Single Wire-Electrode Ac Probe In 3.5wt.% Nacl, Zhen-Wen Zou, Da-Jiang Zheng, Zi-Ming Wang, Guang-Ling Song

Journal of Electrochemistry

In this paper, a recently developed single wire-electrode AC probe technology which does not need a reference or counter electrode was employed to investigate the electrochemical corrosion and sacrificial anode protection behaviors of steel and zinc in 3.5wt.% NaCl. With this simple, fast, reliable and stable probe, the instantaneous corrosion rate and accumulated corrosion loss of carbon steel in 3.5wt.% NaCl were measured, and the results revealed that both were greater than those of zinc. Furthermore, the observed different corrosion behaviors between carbon steel and zinc during the immersion could be caused by their different surface films. With the galvanic …

Load-Bearing Capacity Of Corroded Reinforced Concrete Structures Caused By Carbonation And Exposed To Xc4, Esko Sistonen

International Conference on Durability of Concrete Structures

Concrete corrosion can be visualized as a combination of chemical reaction on concrete and electrochemical reaction on steel reinforcement. Failure of steel reinforcement due to corrosion can inflict significant stress on concrete during load distribution. As such, it is necessary to analyse the long-term effects of corrosion on the load bearing capacity and bending strength of steel reinforcement. This research investigated the mechanical and electrochemical properties of concrete exposed to long-term corrosion for a period of 16 years. Non-destructive testing like crack width measurements, visual examination, electrochemical measurements using Galva Pulse and determination of average chloride content were undertaken to …

Numerical Study Of Oxidation In Stainless Steel Alloy Ep-823 By Liquid Lead-Bismuth Eutectic, Rajyalakshmi Palaparty

UNLV Theses, Dissertations, Professional Papers, and Capstones

The oxidation of stainless steel is influenced by the presence of oxygen in the surrounding medium; the oxygen reacts with the alloy to form an oxide. In certain environments, such as nuclear reactor coolant systems, minimal oxidation of the stainless steel containment functions as a protective shield from corrosive coolants such as liquid lead-bismuth eutectic.

In the current study, this minimal oxidation is evaluated for a system in which corrosion-resistant stainless steel alloy EP-823 is subject to an environment of flowing oxygenated liquid lead-bismuth eutectic at a temperature of 743 K, whereby the thickness of the forming oxide layer is …

Microstructural Investigation Of Vintage Pipeline Steels Highly Susceptible To Stress Corrosion Cracking, Monica Adriana Torres

Open Access Theses & Dissertations

The use of pipelines for the transmission of gas offers not only efficiency, but a number of economic advantages. Nevertheless, pipelines are subject to aggressive operating conditions and environments which can lead to in-service degradation [1] and thus to failures. These failures can have catastrophic consequences, such as environmental damage and loss of life [2]. One of the most dangerous threats to pipeline integrity is stress corrosion cracking (SCC). Despite the substantial progress that has been achieved in the field, due to the complex nature of this phenomenon there is still not a complete understanding of this form of external …

Galvanic Corrosion On Monel K-500 And 1018 Carbon Steel Couple, John K. Nnyanzi

Williams Honors College, Honors Research Projects

The purpose of this research project was to evaluate galvanic damage on 1018 Carbon Steel coupled to Monel K-500 at varying rotation speeds on a rotating cylinder electrode in an aerated solution of ASTM artificial seawater. The work in this project is and attempt to study corrosion behavior for a Monel fastener coupled to a Carbon Steel plate. Polarization curves of each material at different rotation speeds were created to predict the corrosion behavior for a galvanic couple of Carbon Steel and Monel. The Potentiodynamic sweeps predict an increase in the corrosion current density for the galvanic couple when then …

The Examination Of Stress Corrosion Cracking In High Strength Carbon Steel Through Combined Mechanical-Electrochemical Testing, Jacob Sines

Williams Honors College, Honors Research Projects

Through the analysis of materials and environments seen in industry a better understanding of the fundamentals behind degradation mechanisms can be observed. The scope of this project was to better understand the fundamentals behind the degradation of high strength pipeline steels in a lab setting to simulate an environment seen in industry. Specifically the degradation mechanisms of high and nearly neutral pH stress corrosion cracking were examined in environments that simulated oil and gas pipelines buried in soil. Experimentation was carried out utilizing X65 carbon steel specimen, a Gamry potentiostat, a CORTEST proof ring, a CORTEST slow strain rate machine, …

Basic Principles And Applications Of Secm In Metal Corrosion, Fa-He Cao, Yan Xia, Wen-Juan Liu, Lin-Rong Chang, Jian-Qing Zhang

Journal of Electrochemistry

Scanning electrochemical microscopy (SECM) is chemical microscopy with higher spatial resolution. After 24 years of development, SECM has been widely applied in mapping and kinetics study of heterogeneous electron transfer in localized processes at solid-liquid or liquid-liquid interfaces. The fundamentals and recent advances of SECM in corrosion applications are described, including SECM mapping and kinetics on localized corrosion of metal or coating. Research work of SECM in corrosion by our group is also introduced. Future applications of SECM in corrosion are highlighted.

Applications Of Spectroscopic Ellipsometry In Corrosion Investigation, Ling-Jie Li, Yu-Ling He, Jing-Lei Lei, Sheng Tao Zhang

Journal of Electrochemistry

As a highly-sensitive and non-destructive in situ technique, spectroscopic ellipsometry has been widely applied in corrosion investigation to acquire the dynamic information of the “electrode-medium” interface during corrosion. This paper lays out some representative demonstrations in several established optical models used to interpret data obtained with spectroscopic ellipsometry in corrosion investigation. In addition, the latest trends in development of this technique are analyzed.

Multifunctional Corrosion Inhibition Behavior Of Zn-Al Calcined Layered Double Hydroxides For Steel Rebar In Nacl Solution, Xiao-Juan Zhang, Jing-Jing Wang, Shi-Gang Dong, Chang-Jian Lin

Journal of Electrochemistry

The Zn-Al layered double hydroxides (Zn-Al LDHs) and calcined products (Zn-Al CLDHs) were synthesized successfully under a routine air atmosphere. The results showed that both Zn-Al LDHs and Zn-Al CLDHs had obvious flake structures. The corrosion inhibition of Zn-Al CLDHs for steel rebar in NaCl solution was studied by electrochemical techniques. It was found that the corrosion rate of steel rebar decreased significantly after the steel rebar was treated by Zn-Al CLDHs in NaCl solution for 3 h. It was indicated that Zn-Al CLDHs could absorb Cl^- and release OH^- during their reconstruction process, which provided dual protection …

The Effects Of Uncommon Silicides On The Oxidation Of Alloys From The Nb-Cr-Si System, Daniel Brendan Voglewede

Open Access Theses & Dissertations

Niobium based alloys are being tapped as potential successors to current nickel base superalloys in high temperature applications. In the aerospace industry, high temperature materials are constantly being pushed to higher temperature regimes in order to improve engine efficiency however current superalloys cannot be pushed further due to melting temperature limitations. Niobium, being a refractory metal, can withstand much higher temperatures than nickel however its oxidation properties are woefully inadequate.

The purpose of this study is to ascertain whether increased silicon additions can improve niobium oxidation properties by: forming ternary silicides with better oxidation properties and by preventing the formation …

Corrosion Characteristics Of Galvanized Flat Steel For Power Grounding In Nacl Solution Medium, Yong Li, Gao-Lin Wu, Bang-Fei Deng, Ping Yang, Xue-Ming Li, Qing-Bin Zong

Journal of Electrochemistry

The corrosion behavior of power grounding galvanized flat steel was studied by polarization measurement, electrochemical impedance spectroscopy and neutral salt spray test in 5% NaCl solutions. The surface morphologies of galvanized coating and structural properties of corrosion products were observed with scanning electron microscope and X-ray diffraction spectrometer, respectively. Results showed that under the temperatures of 20~60℃, the corrosion currents of galvanized flat steel increased with the temperature rising. The corrosion rate at 60℃ was 0.8408 mA?cm-2, which is 2.9 times larger than that at 20℃. The corrosion rate dropped after reaching the maximal value of 1.95 mg?cm-2?d-1 when the …

Corrosion Electrochemical Behavior Of Am60 Magnesium Alloys In Automobile Engine Coolants, Ling-Jie Li, Sha Wang, Yin Xiao, Jun Lan, Jing-Lei Lei, Sheng-Tao Zhang, Fu-Sheng Pan

Journal of Electrochemistry

The polarization measurements and electrochemical impedance spectroscopy(EIS) were used to study the corrosion electrochemical behavior of AM60 magnesium alloys in three kinds of commercial coolants for automobile engine.Results show that the tested commercial coolants are slightly corrosive to AM60 magnesium alloys and their corrosivity varies from coolant to coolant.The coolant C is the least corrosive among the studied commercial coolants and the coolant A is more corrosive than the coolant B and C.The coolant C appears to be the most promising coolant for automobile engine made by magnesium alloys.The coolant resistivity plays an important role in the corrosion of AM60 …

Effect Of Cldh On Rebar Corrosion Behavior In Chloride Contaminated Neutral Pore Solutions, Yu-Ming Tang, Le Niu, Yu Zuo

Journal of Electrochemistry

The effect of calcined LDH-MgAl-CO3 on rebar corrosion behavior in chloride ion contaminated neutral concrete pore solutions was investigated in this paper.Corrosion potentials of rebars in pore solutions after treatment with CLDH were higher than before treatment.According to polarization tests,passivated region of rebars in pore solutions after treatment with CLDH was found apparently instead of activation.EIS tests showed that CLDH made the impedance of specimens increase.The measurements of pH and chloride ion concentration after treatment indicated that / of pore solutions decreased by 4～5 magnitude orders.

Studied Corrosion Behaviors Of Reinforcing Steel In Concrete By A Single-Dimensional Array Electrode, Lan-Qiang Li, Shi-Gang Dong, Rong-Gui Du, Chang-Jian Lin

Journal of Electrochemistry

A single-dimensional array electrode was developed as a new electrochemical technique to image corrosion potential,galvanic current and polarization curves of reinforcing steel in concrete during corrosion process.Combining with the polarization behavior for each micro-electrode,the interactions between corrosion macrocell and corrosion microcell of the steel in concrete were evaluated.It was noticed that the corrosion macrocell and microcell occurred independently in difference regions at the initial stage of corrosion.The corrosion macrocell current can be in situ followed by corrosion potential imaging.The corrosion propagation of steel in concrete is closely related to the interactions between corrosion macrocell and corrosion microcell.

Synergism Of Complex Additives Of Dtab+Ktl For Zinc Corrosion Inhibition In Koh Solutions, Sheng-Zhou Lin, Zeng-Xin Cai, Gui-Sheng Wang, He-Bing Zhou, Wei-Shan Li

Journal of Electrochemistry

The electrochemical behaviors of Zn in 3mol/L KOH solution containing several kinds of inhibitors were investigated by weight-loss,electrochemical methods and SEM. The results showed that both the single ad-ditive and the mixed additives can suppress the corrosion of zinc in 3 mol/LKOH solution. And the inhibition ef-feciency of the mixed additives is higher than that of any single additive because of the synergistic effect between KTL and DTAB. The adsorption of DTAB on the surface of zinc has been enhanced in the presence of KTL.

Developments Of Scanning Electrochemical Probes And Their Applications In Studying Of Localized Corrosions, Chang-Jian Lin, Yan Li, Bin Lin, Rong-Gang Hu, Min Zhang, Xiang-Dong Zhuo, Rong-Gui Du

Journal of Electrochemistry

The electrochemical inhomogeneities always exist at the interface of metal/solution,and play an important and often controlling role in localized corrosion of metals in a given environment.It is necessary to develop in situ imaging techniques for further studying the electrochemical and environmental inhomogeneities at the interface of metal/solution for the localized corrosion system.In this paper,various techniques with spatial resolution,such as scanning micro reference electrode(SMET),scanning electrochemical microscope(SECM),atomic force microscope(AFM),and scanning Kelvin probe(SKP),and their applications in corrosion studies were briefly reviewed.The chemical probes and array electrode have been developed.It was concentrated to describe our newly developed techniques of the scanning electrochemical probes,including SMET …

Electrodeposition Of Al On Magnesium Alloy In Ionic Liquid, Tsai Wen-Ta, Shu-You Chen, Mu-Huan Zhuang, Chang Jeng-Kuei, Yi-Wen Sun

Journal of Electrochemistry

Electrodeposition of a metallic aluminum on a magnesium alloy in acidic aluminum chloride-1-ethyl-3-methylimidazolium chloride ionic liquids(AlCl3-EMIC) was investigated.The effects of current density and AlCl3 content in the ionic liquid on the electrodeposition behavior were studied.The results showed that aluminum could be successfully electrodeposited on the AZ91D substrate.At-0.2 V,the ionic liquid containing 60 m/o AlCl3 was optimum for Al electrodeposition.The current efficiency was higher if electrodeposition was performed at a lower applied current density.The existence of Al coating could caused a substantial increase in open circuit potential,reducing the susceptibility of Mg alloy to corrosion.The results of electrochemical impedance spectroscopy showed that …

Corrosion Inhibition Of Magnesium Alloy In 3.5% Nacl Medium By Tungstate, Ling-Jie Li, Zhi-Ming Yao, Jing-Lei Lei, Dong-Hai He, Sheng-Tao Zhang, Fu-Sheng Pan

Journal of Electrochemistry

Electrochemical impedance spectroscopy(EIS),Tafel polarization curves and scanning electron microscopy(SEM) were used to study the corrosion inhibition of AZ61 magnesium alloy in 3.5% NaCl medium with tungstate.Results showed that tungstate demonstrates strong inhibition to the corrosion of AZ61 magnesium alloy.At the concentration of 0.01 mol/L,tungstate has a high inhibition efficiency 75.5%.Tungstate is an anodic inhibitor that mainly inhibited the anodic reactions of magnesium alloy through forming a compact protective layer that covered the magnesium alloy surface active sites.

Corrosion Electrochemical Behavior Of Az31 And Az61 Magnesium Alloys In Simulated Sea Water, Ling-Jie Li, Sheng-Hai Yu, Jing-Lei Lei, Chuan-Pu Liu, Sheng-Tao Zhang, Fu-Sheng Pan

Journal of Electrochemistry

Tafel polarization curves and electrochemical impedance spectroscopy(EIS) techniques were employed to investigate the corrosion electrochemical behavior of AZ31 and AZ61 magnesium alloys.Scanning electron microscopy(SEM) was used to observe the alloy microstructure and corrosion morphology.The variation of the bulk corrosive medium pH with immersion time was recorded during the exposure of the alloys to simulated sea water.Results show that AZ61 magnesium alloy exhibits much better anti-corrosion ability than AZ31 magnesium alloy.The different corrosion behavior between the two magnesium alloys is correlated with their different content of Al alloying element.The higher content of Al in AZ61 alloy leads to the homogenerous microstructure …

Study On Electrochemical Impedance Spectroscopy Of Carbon Steel Eroded In Methyldiethanolamine Solution, Dong-Ping Wei, Rong-Zong Hu, Dan-Mei Pan, Wei-Xiong Huang, Rui Dong

Journal of Electrochemistry

Corrosion behavior of carbon steel in methyldiethanolamine(MDEA) solution was investigated by Electrochemical Impedance Spectroscopy(EIS).The results were showed that the corrosion rate of carbon steel in solution containing dissolved oxygen is higher than that in solution removed of dissolved oxygen before cathodic activation.They were reversed after cathodic activation.The corrosion rate is increased at first and then decreased when the concentration of MDEA is increased in the blank solutions.In the simulated solutions containing quantities of!heat-stable salts(HSS),the corrosion rate is decreased monotonously with increase of the MDEA concentration.As anodic polarization potential is increased,the EIS of carbon steel in HSS simulated solution showed characteristics …

Corrosion Electrochemical Behavior Of Aluminum Flake Pigmented Water-Borne Epoxy Coating On Carbon Steel In Nacl Solution, Li-Li Xue, Li-Kun Xu, Qing-Fen Li, Hong-Qing Song, Wen-Juan Zhou, Guang-Zhang Chen

Journal of Electrochemistry

The corrosion electrochemical behavior of a water-borne epoxy coating pigmented with aluminum flake on carbon steel with artificial scratch defect was studied in 3.5% NaCl solution using electrochemical impedance spectroscopy(EIS)and scanning vibrating electrode technique(SVET).The results indicated that the defect presented anodic electroactivity at the initial stage of immersion,which extended gradually with time from the scratch into the neighboring coating,lowering the coating impedance.With further immersion,however,the electroactivity of the coating/steel interface decreased significantly due to the self-repairing of the corrosion products,causing an obvious increase of the coating impedance.In the later period of immersion,more scattered electroactive areas appeared under the coating because of …

Effect Of Cracks On Corrosion Of Rebar In Concrete Studied By Wire Beam Electrode, Guo-Xi Li

Journal of Electrochemistry

The effects of crack and ethanolamine on corrosion of rebar in concrete were studied by measuring the distribution of corrosion potential and polarization resistance of iron wires in 10% NaCl solution.The results showed that the diffusion of water,oxygen and chloric ion toward concrete was accelerated by the crack which intensified the nonuniform corrosion of iron wire with the regions near to crack as anode and the uncracked regions as cathode.Ethanolamine could diffuse into the body of concrete and absorb on the surface of iron wire,which reduced iron corrosion evidently and successfully inhibited the nonuniform corrosion caused by crack without changing …

A Study Of Three Corrosion Inhibitors For Reinforcing Steel In Sps Solution By Electrochemical Methods, Bing Zhao, Rong-Gui Du, Chang-Jian Lin

Journal of Electrochemistry

Some electrochemical techniques such as linear polarization,electrochemical noise and EIShave been employedto study the inhibition behavior of N-lauroyl sarcosinate,β-sodium glycerophosphate and D-sodium gluconate for the reinforcing steel immersed in simulated concrete pore solution(SPS) with NaCl addition.The results show that D-sodium gluconatehas an obvious inhibitive effect for the reinforcing steelin containingCl~(-)SPS solution.It has been proposed that the corrosion inhibition of D-sodium gluconate is due to its competitive adsorption and precipitation on steel surface in the simulated concrete environment.

Corrosion Behavior Of Sml,Erw Pipeline Steels Exposed To Seamud, Wei Hua

Journal of Electrochemistry

The corrosion behavior of API Spec X60 pipeline steels, including electric resistance welding(ERW) and Seamless (SML) types,in sea mud gathered fromYangtse River estuaryof the East China Sea was investigatedthrough linear polarization resistance, potentio-dynamic polarizationand electrochemical impedance measurements.The result indicate the improved corrosion resistance of SML in sea mud. The oxygen diffusion in the cathode zone determines the corrosion behavior of pipeline steel in sea mud.

Study Of Anti-Corrosion Property On Poly(An-Co-Oas)/Epoxy, Qing-Wu Wang, Geng-Chao Wang

Journal of Electrochemistry

polyaniline, polyanisidine and their copolymer poly(An-co-oAs) were synthesized via the solution chemical oxidative polymerization of aniline and anisidine in an acidic aqueous medium, and their properties and structure were characterized. The electrochemical method were applied to evaluate the corrosion behavior of tined iron uncoated or coated by polyaniline, poly(An-o-oAs), polyanisidine and poly(An-co-oAs)/epoxy blend in acid or saline aqueous solution. The result showed that with the increase of anisidine content, the solubility of polymers is improved apparently but their oxidation extent decreases accordingly. It is also founded that polyaniline, poly(An-co-oAs) and polyanisidine all have good anti-corrosion properties, and their anti-corrosion capacity …

Electrodeposition Nanolaminated Growth Of Zinc, Ying Cao, Tian-Hui Shen, Jing-Yuan Yao, Gui-Fu Ding

Journal of Electrochemistry

Nanolaminated growth of the electrodeposition of zinc was studied. The structure and size of crystalline in zinc coatings were investigated by using FEG-TEM and XRD. The corrosion tests of the zinc deposition and the Coatings-Neutral salt spray test were performed, the capability in corrosion resistance of the nanolaminated growth was better than that of others.