Engineering Commons^™

Calculation Of Hydraulic Resistance Of A Tubular-Gridse Nozzle With Spiral Turbulizers, Nurmukhamedov Habibulla Sagdullaevich, Mavlonov Elbek Tulkinovich, S.Kh. Nishonova, Kh.S. Nurmukhamedov

Chemical Technology, Control and Management

The article presents the results of an experimental study on the hydraulic resistance of a tubular-grid nozzle made of smooth pipes and pipes with spiral turbulators. Experiments were carried out with nozzles made of smooth pipes and pipes with turbulators. Spiral turbulators are placed discretely with a step t/d=0,3125-0,9375 and installed on a tube sheet in a checkerboard pattern with a step s/d=1,15-10. Experimental studies were carried out with air flow in the transition region.

It has been established that with increasing numerical values of the dimensionless parameter s/d, the resistance of the pipe package decreases from 1,3 to 1,8 …

Evaluation Of The Efficiency Of Diesel Locomotives On The Section Of Marokand - Kattakurgan Of Uzbek Railway, Oleg Sergeyevich Ablyalimov, Jasur Djura Ug'li Khodjiyev

Journal of Tashkent Institute of Railway Engineers

A comparative analysis of the efficiency of using diesel traction locomotives in the Marokand - Kattakurgan section of the Uzbek Railway for freight trains with and without stops at intermediate stations, siding and separate points is given. Mathematical models of conducting freight trains by diesel-powered locomotives were developed, specific resultant forces of the train were calculated and built in the modes of traction, idling and braking, curves of the speed of movement and time of the train on the considered real railway section. The kinematic parameters of the movement of freight trains and the main energy indicators of the transportation …

Calculation Of Hanging Shells Complex Geometry, Sayidmahsud Razzakov, Gennady Fridman, Rasul Khuzhakulov

Journal of Tashkent Institute of Railway Engineers

A method for calculating large-span, spatial hanging shells is presented. A resolving system of equations is obtained for determining the stress-strain state of the hanging shells, the support contour, bearing and stabilizing cables

Investigation Of Way Embankment Stability On Movement Of High Speed Trains, Mirzakhid Khamitovich Miralimov, Shakhboz Ulugbekovich Normurodov

Journal of Tashkent Institute of Railway Engineers

In this paper is considered the problem related with a stressed state of railway embankments taking into account of dynamic loadings from high-speed trains. In the offered technical method is giving wave nature transmissions of dynamic loading from the passenger trains and their interaction of soil layers with various parameters. The design procedure gives a clear physical and mathematical pattern, where all formulas are in detail shown and simple for understanding. Calculation is conducted numerically in two stages. Considering from classical principles of structural mechanics, the first calculation stage of the railway structures includes deformation of the railway sleepers taking …

A Procedure For The Calculation Of The Perceived Loudness Of Sonic Booms, Christian R. Bolander, Douglas F. Hunsaker, Hao Shen, Forrest L. Carpenter

Mechanical and Aerospace Engineering Student Publications and Presentations

Implementing a method to calculate the human ear’s perceived loudness of a sonic boom requires consulting scattered literature with varying amounts of detail. This work describes a comprehensive implementation of Stevens’ Mark VII in Python, called PyLdB. References to literary works are included in enough detail so that the reader could use this work as a guide to implement the Mark VII algorithm. The details behind the mathematics of the Mark VII algorithm are included and PyLdB is used to calculate the perceived loudness of an example pressure signature. PyLdB is benchmarked against a widely used and validated code by …

Spatial Calculation Of The Steel Frame Of A Multi-Storey Building, G. Freedman

Problems of Architecture and Construction

In paper the instance of calculation of the space steel framework of a multistorey building in altitude of 8 floors with use of the personal computer LYRE is observed. A framework - communication has system with an internal kernel of rigidness. All aspects of loadings, including wind and seismic are considered. Selection of cross-sections of elements of a framework in the application of LIRA-STK is executed.

Comparative Analysis Of The Results Of Truss Calculation With Hinge And Rigid Nodes, H. Ibragimov

Problems of Architecture and Construction

In paper results of calculation of trusses by span of 24 m with various steps of panels are resulted at the hinge and the rigid joint of knots and the comparative analysis of the counted trusses is resulted.

Research Note: On The Magnitude Of Error In The Calculation Of Mean Room Surface Exitance, James Duff

Articles

Two formulae currently exist for calculating mean room surface exitance. This research note explains and demonstrates that one of these formulae is erroneous under certain conditions and stresses that the alternative expression should generally be used for computing mean room surface exitance.

Fire And Life Safety Analysis Of Cal Poly Engineering Iv, Business In Amarillo, Tx And Costco, Russell B. Bainbridge Iii

Fire Protection Engineering: Culminating Experience Project Reports

The main fire protection disciplines ‐ Egress Analysis and Design, Fire Detection, Alarm and Communication Systems, Water‐based Fire Suppression Systems and Structural Fire Protection ‐ are covered in this report.

For Egress Analysis and Design, the California Polytechnic State University’s Engineering IV building was analyzed and covered in the first portion of this report. The building was analyzed against the 2015 edition of NFPA 101 and the 2015 edition of the International Building Code. It is a typical university engineering building with classrooms, professors’ offices and some laboratories. The occupancies, the occupant load, exit widths, exit lengths and number of …

Modeling Of Gas Production From Shale Reservoirs Considering Multiple Transport Mechanisms, Chaohua Guo, Mingzhen Wei, Hong Liu

Geosciences and Geological and Petroleum Engineering Faculty Research & Creative Works

Gas transport in unconventional shale strata is a multi-mechanism-coupling process that is different from the process observed in conventional reservoirs. In micro fractures which are inborn or induced by hydraulic stimulation, viscous flow dominates. And gas surface diffusion and gas desorption should be further considered in organic nano pores. Also, the Klinkenberg effect should be considered when dealing with the gas transport problem. In addition, following two factors can play significant roles under certain circumstances but have not received enough attention in previous models. During pressure depletion, gas viscosity will change with Knudsen number; and pore radius will increase when …

Evaluation Of 3d Gamma Index Calculation Implemented In Two Commercial Dosimetry Systems, Aitang Xing, Sankar Arumugam, Shrikant Deshpande, Armia George, Philip J. Vial, Lois C. Holloway, Gary Goozee

Faculty of Engineering and Information Sciences - Papers: Part A

3D Gamma index is one of the metrics which have been widely used for clinical routine patient specific quality assurance for IMRT, Tomotherapy and VMAT. The algorithms for calculating the 3D Gamma index using global and local methods implemented in two software tools: PTW-VeriSoft (R) r as a part of OCTIVIUS 4D dosimeter systems and 3DVH (TM) from Sun Nuclear were assessed. The Gamma index calculated by the two systems was compared with manual calculated for one data set. The Gamma pass rate calculated by the two systems was compared using 3%/3mm, 2%/2mm, 3%/2mm and 2%/3mm for two additional data …

I-125 Ropes Eye Plaque Dosimetry: Validation Of A Commercial 3d Ophthalmic Brachytherapy Treatment Planning System And Independent Dose Calculation Software With Gafchromic Ebt3 Films, Joel Poder, Stephanie Corde

Stéphanie Corde

Purpose: The purpose of this study was to measure the dose distributions for different Radiation Oncology Physics and Engineering Services, Australia (ROPES) type eye plaques loaded with I-125 (model 6711) seeds using GafChromic R EBT3 films, in order to verify the dose distributions in the Plaque SimulatorTM (PS) ophthalmic 3D treatment planning system. The brachytherapy module of RADCALC R was used to independently check the dose distributions calculated by PS. Correction factors were derived from the measured data to be used in PS to account for the effect of the stainless steel ROPES plaque backing on the 3D dose distribution. …

Improvements In Dose Calculation Accuracy For Small Off-Axis Targets In High Dose Per Fraction Tomotherapy, Nicholas Hardcastle, Adam Bayliss, Jeannie Wong, Anatoly B. Rosenfeld, Wolfgang A. Tome

Anatoly Rozenfeld

Purpose: A recent field safety notice from TomoTherapy detailed the underdosing of small, off-axis targets when receiving high doses per fraction. This is due to angular undersampling in the dose calculation gantry angles. This study evaluates a correction method to reduce the underdosing, to be implemented in the current version (v4.1) of the TomoTherapy treatment planning software. Methods: The correction method, termed "Super Sampling" involved the tripling of the number of gantry angles from which the dose is calculated during optimization and dose calculation. Radiochromic film was used to measure the dose to small targets at various off-axis distances receiving …

I-125 Ropes Eye Plaque Dosimetry: Validation Of A Commercial 3d Ophthalmic Brachytherapy Treatment Planning System And Independent Dose Calculation Software With Gafchromic Ebt3 Films, Joel Poder, Stephanie Corde

Faculty of Engineering and Information Sciences - Papers: Part A

Purpose: The purpose of this study was to measure the dose distributions for different Radiation Oncology Physics and Engineering Services, Australia (ROPES) type eye plaques loaded with I-125 (model 6711) seeds using GafChromic R EBT3 films, in order to verify the dose distributions in the Plaque SimulatorTM (PS) ophthalmic 3D treatment planning system. The brachytherapy module of RADCALC R was used to independently check the dose distributions calculated by PS. Correction factors were derived from the measured data to be used in PS to account for the effect of the stainless steel ROPES plaque backing on the 3D dose distribution. …

Improvements In Dose Calculation Accuracy For Small Off-Axis Targets In High Dose Per Fraction Tomotherapy, Nicholas Hardcastle, Adam Bayliss, Jeannie Wong, Anatoly B. Rosenfeld, Wolfgang A. Tome

Faculty of Engineering and Information Sciences - Papers: Part A

Purpose: A recent field safety notice from TomoTherapy detailed the underdosing of small, off-axis targets when receiving high doses per fraction. This is due to angular undersampling in the dose calculation gantry angles. This study evaluates a correction method to reduce the underdosing, to be implemented in the current version (v4.1) of the TomoTherapy treatment planning software. Methods: The correction method, termed "Super Sampling" involved the tripling of the number of gantry angles from which the dose is calculated during optimization and dose calculation. Radiochromic film was used to measure the dose to small targets at various off-axis distances receiving …

Joint Analysis Of Beef Growth And Carcass Quality Traits Through Calculation Of Co-Variance Components And Correlations., H R. Mirzaei, Arunas P. Verbyla, W. S. Pitchford

Faculty of Engineering and Information Sciences - Papers: Part A

A joint growth-carcass model using random regression was used to estimate the (co)variance components of beef cattle body weights and carcass quality traits and correlations between them. During a four-year period (1994-1997) of the Australian "southern crossbreeding project", mature Hereford cows (N = 581) were mated to 97 sires of Jersey, Wagyu, Angus, Hereford, South Devon, Limousin, and Belgian Blue breeds, resulting in 1141 calves. Data included 13 (for steers) and 8 (for heifers) body weight measurements approximately every 50 days from birth until slaughter and four carcass quality traits: hot standard carcass weight, rump fat depth, rib eye muscle …

How Do You Interpret A Confidence Interval?, Paul Savory

Industrial and Management Systems Engineering: Instructional Materials

A confidence interval (CI) is an interval estimate of a population parameter. Instead of estimating the parameter by a single value, a point estimate, an interval likely to cover the parameter is developed. Many student incorrectly interpret the meaning of a confidence interval. This paper offers a quick overview of how to correctly interpret a confidence interval.

Why Divide By (N-1) For Sample Standard Deviation?, Paul Savory

Industrial and Management Systems Engineering: Instructional Materials

In statistics, the sample standard deviation is a widely used measure of the variability or dispersion of a data set. The standard deviation of a data set is the square root of its variance. In calculating the sample standard deviation, the divisor is the number of samples in the data set minus one (n-1) rather than n. This often confuses students. This paper offers a quick overview of why the divisor is (n-1) for calculating the sample standard deviation.

Optical Property And Electronic Band Structure Of A Piezoelectric Compound Ga3po7 Studied By The First-Principles Calculation, Zhenxiang Cheng, Xiaolin Wang

Australian Institute for Innovative Materials - Papers

The structure, electronic and optical properties of a piezoelectric material, Ga₃PO₇ were studied by first-principles calculations in the framework of density functional theory. The calculated structure is in agreement with the experimental data. Band structure reveals that Ga₃PO₇ has a band gap of 3.69 eV. Analysis of partial density of states and Mulliken charge population indicates existence of GaO₅ and PO₄ anion groups in Ga₃PO₇. Furthermore, its optical properties, including dielectric constant, absorption, reflectivity, refractive index, and electron loss were calculated and analysed, which show that Ga_{3 …}

Scatterer Size Estimation In Pulse-Echo Ultrasound Using Focused Sources: Calibration Measurements And Phantom Experiments, Timothy A. Bigelow, William D. O'Brien

Timothy A. Bigelow

In a companion paper [T. A. Bigelow and W. D. O'Brien Jr., J. Acoust. Soc. Am. 116, 578 (2004)], theory, supported by simulations, showed that accurate scatterer size estimates could be obtained using highly focused sources provided that the derived generalized attenuation-compensation function was used and the velocity potential field near the focus could be approximated as a three-dimensional Gaussian. Herein, the theory is further evaluated via experimental studies. A calibration technique is developed to find the necessary equivalent Gaussian dimensions for a focused source using reflections obtained from a rigid plane scanned through the focus. Then, the theoretical analysis …

Scatterer Size Estimation In Pulse-Echo Ultrasound Using Focused Sources: Theoretical Approximations And Simulation Analysis, Timothy A. Bigelow, William D. O'Brien

Timothy A. Bigelow

The speckle in ultrasound images has long been thought to contain information related to the tissue microstructure. Many different investigators have analyzed the frequency characteristics of the backscattered signals to estimate the scatterer acoustic concentration and size. Previous work has been mostly restricted to unfocused or weakly focused ultrasound sources, thus limiting its implementation with diagnostically relevant fields. Herein, we derive equations capable of estimating the size of a-scatterer for any reasonably focused source provided that the velocity potential field in the focal region can be approximated as a three-dimensional Gaussian beam, scatterers are a sufficient distance from the source, …

The Fracture Of Ice On Scales Large And Small: Arctic Leads And Wing Cracks, E. M. Schulson, W. D. Hibler

Dartmouth Scholarship

From observations and calculations of crack patterns in ice, it is suggested that a similar mechanism may account for cracking over a wide range of scales.