Engineering Commons^™

An Experimental Investigation Of The New Vibration Viscometer, Jamshidbek Ulugbek Ugli Shamuratov

Technical science and innovation

The characteristics of the new oscillating-plate viscometer have been investigated experimentally. The results obtained are as follows: the resonant frequency of plate oscillation decreases with increasing viscosity; the apparatus constant 𝐾 determined experimentally includes the end and slip effects; the dimensions of the plate should be determined by referring to empirical relations between 𝜌𝜇 and Λ(≡{(𝐸𝑎𝐸)−1}𝑛) for various dimensions of the plate; where 𝜌 is the density, 𝜇 is the viscosity; 𝐸𝑎 the resonant amplitude of plate in the air; E the amplitude of plate in a liquid, and 𝑛 a constant. If the distance between the plate and the …

Modeling The Influence Of Vibration On Flow Through Embedded Microchannels, Joseph S. Seamons

Theses and Dissertations

The influence of vocal fold (VF) vibration on perfused flow through VF vasculature is an area of research that has previously received limited attention. The aim of the research presented in this thesis was to contribute towards an improved understanding of the effects vibration on perfusion through vasculature within the VFs. This was done using a series of computational simulations of geometric changes to, and perfusion through, microchannels embedded in VF models. A computational structural model based on synthetic VF models used in previous experimental studies was first developed. The model and its embedded microchannel were initially studied under static …

Vibration-Based Machine Learning Models For Condition Monitoring Of Railroad Rolling Stock, Sergio M. Martinez

Theses and Dissertations

One of the primary causes of rail rolling stock derailments is attributed to bearing and wheel axle failures. The health of train bearings is primarily monitored at target locations through wayside detection systems. This practice is susceptible to bearing failure and potential derailments at points in between these wayside systems. To remedy this, the University Transportation Center for Railway Safety (UTCRS) has developed a wireless onboard monitoring system that can continuously monitor the vibration response, which directly correlates to the health of bearings. This data is used to train regression-based machine learning algorithms and long-term prediction neural networks to predict …

Vibration Fatigue Of Leaded Solder Joint Interconnects For Pcb Electronics, John Crowder

All Theses

With the increasing prevalence of electronic equipment worldwide, there is also a decrease in the size of the components on their printed circuit boards (PCBs), leading to an increase in the density of these components. A significant amount of failure in electronic equipment is vibration fatigue of solder joints and their attachments. However, the complexity of these PCBs and their components has made finite element modeling (FEM) more complex, adding considerable time to create and analyze a model.

This paper aims to provide a literature review for the vibration fatigue of leaded solder components, create a test setup, and validate …

Dynamics And Steering Of A Vibration-Driven Bristle Bot In A Pipe System, Ian Stewart

All Theses

Soft vibrational robots are robots that incorporate compliant structures into their design and are driven by oscillating actuators. A recent, popular version of a soft vibrational robot is the bristle bot, which uses flexible bristles and a vibration motor to propel itself across surfaces and through pipes. This motion is primarily driven by stick-slip dynamics resulting from asymmetric frictional forces applied at the bristle tips. Depending on the frequency of vibration of the motor, the robot experiences various resonance regions allowing it to maneuver in different directions. Attaching bristles to all sides of the robot and placing it in a …

Programmable Vibration Table Retrofit With Eagle Medical, Jonathan Ilagan, Madhav Asok, Max Lewter

Biomedical Engineering

This project aimed to repair and upgrade a vibration table used for package testing for the sponsor, Eagle Medical - a medical packaging and sterilization company based in Paso Robles, California. The current vibration table is not programmable and lacks circuit diagrams, making it difficult to repair. In addition, it is not functional due to internal circuitry issues and power requirements. To address these issues, the team will implement several upgrades to improve the product and allow for better random cyclic vibration testing. A full assessment of the existing vibration table will be conducted to ensure the viability of these …

Perfusion Pressure-Flow Relationships In Synthetic Poroelastic Vocal Fold Models, Cooper B. Thacker

Theses and Dissertations

The purpose of this research was to study perfusion pressure-flow relationships in self-oscillating synthetic poroelastic vocal fold (VF) models before, during, and after vibration. This was accomplished by developing a custom ultra-soft poroelastic material, incorporating the poroelastic material as the cover layer in a synthetic VF model, and studying the model vibratory response and the flow rate of fluid perfused through the cover layer while undergoing flow-induced vibration. The custom ultra-soft poroelastic material was developed using the method of direct templating with sucrose spheres as the sacrificial template and silicone as the infiltration medium. The average modulus of elasticity of …

Design And Modeling Of A Pvdf-Trfe Flexible Wind Energy Harvester, Berkay Kullukçu, Levent Beker

Turkish Journal of Electrical Engineering and Computer Sciences

This study presents the simulation, experimentation, and design considerations of a Poly(vinylidene fluoride co-trifluoroethylene)/ Polyethylene Terephthalate (PVDF-TrFe / PET), laser-cut, flexible piezoelectric energy harvester. It is possible to obtain energy from the environment around autonomous sensor systems, which can then be used to power various equipment. This article investigates the actuation means of ambient vibration, which is a good candidate for using piezoelectric energy harvester (PEH) devices. The output voltage characteristics were analyzed in a wind test apparatus. Finite element modeling (FEM) was done for von Mises stress and modal analysis. Resonance frequency sweeps, quality factors, and damping ratios of …

Alternative Method For Low Frequency Impact Sound Measurement For Building Field Tests, Sunit Girdhar

Dissertations, Master's Theses and Master's Reports

What do high heels, dog nails, and dragging furniture have in common? They are all frequent sources of noise pollution and annoyance in multi-story buildings. Building codes exist to control and mitigate such noise, but these codes are outdated and fail to protect the residents against noise annoyance. Footstep noise is still the number one cause of complaints among the residents. The impact performance of floor-ceiling assemblies is characterized using a single-number rating called the Impact Sound Rating (ISR). A standard tapping machine is used in pre-defined locations on the floor and the radiated Sound Pressure Level (SPL) is measured …

Additively Manufactured Polymeric Surface-Based Lattice Structures For Vibration Attenuation, Imabin Kelvin Ekpelu

Browse all Theses and Dissertations

The focus of this study was to select triply periodic minimal surface (TPMS) structures made of 3D-printed polymers. The primary variables in this study were: TPMS shape, lattice volume ratio, and lattice material. Vibration absorption was characterized by damping ratio via transmissibility at the system’s natural frequency. The vibration testing was performed using an electro-dynamic shaker, a known mass, an input/control accelerometer, and an output/response accelerometer. The 3D-printed absorber/lattice was mounted to the shaker baseplate and a mass will be mounted on top of the absorber. One accelerometer will be mounted to the shaker baseplate and the other will be …