Engineering Commons^™

Experimental Investigation Of The Thermochemical Reduction Of Arsenite And Sulfate: Low Temperature Hydrothermal Copper, Nickel, And Cobalt Arsenide And Sulfide Ore Formation, Nicholas Allin

Graduate Theses & Non-Theses

Experiments were conducted to determine the relative rates of reduction of aqueous sulfate and aqueous arsenite (As(OH)₃,aq) using foils of copper, nickel, or cobalt as the reductant, at temperatures of 150ºC to 300ºC. At the highest temperature of 300°C, very limited sulfate reduction was observed with cobalt foil, but sulfate was reduced to sulfide by copper foil (precipitation of Cu₂S (chalcocite)) and partly reduced by nickel foil (precipitation of NiS₂ (vaesite) + NiSO₄·xH₂O). In the 300ºC arsenite reduction experiments, Cu₃As (domeykite), Ni₅As₂, or CoAs (langisite) …

High-Performing Pgm-Free Aemfc Cathodes From Carbon-Supported Cobalt Ferrite Nanoparticles, Xiong Peng, Varchaswal Kashyap, Benjamin Ng, Sreekumar Kurungot, Lianqin Wang, John R. Varcoe, Mustain E William

Faculty Publications

Efficient and durable non-precious metal electrocatalysts for the oxygen reduction reaction (ORR) are highly desirable for several electrochemical devices, including anion exchange membrane fuel cells (AEMFCs). Here, cobalt ferrite (CF) nanoparticles supported on Vulcan XC-72 carbon (CF-VC) were created through a facile, scalable solvothermal method. The nano-sized CF particles were spherical with a narrow particle size distribution. The CF-VC catalyst showed good ORR activity, possessing a half-wave potential of 0.71 V. Although the intrinsic activity of the CF-VC catalyst was not as high as some other platinum group metal (PGM)-free catalysts in the literature, where this catalyst really shined was …

Fischer–Tropsch: Product Selectivity–The Fingerprint Of Synthetic Fuels, Wilson D. Shafer, Muthu Kumaran Gnanamani, Uschi M. Graham, Jia Yang, Cornelius M. Masuku, Gary Jacobs, Burtron H. Davis

Center for Applied Energy Research Faculty and Staff Publications

The bulk of the products that were synthesized from Fischer–Tropsch synthesis (FTS) is a wide range (C₁–C₇₀₊) of hydrocarbons, primarily straight-chained paraffins. Additional hydrocarbon products, which can also be a majority, are linear olefins, specifically: 1-olefin, trans-2-olefin, and cis-2-olefin. Minor hydrocarbon products can include isomerized hydrocarbons, predominantly methyl-branched paraffin, cyclic hydrocarbons mainly derived from high-temperature FTS and internal olefins. Combined, these products provide 80–95% of the total products (excluding CO₂) generated from syngas. A vast number of different oxygenated species, such as aldehydes, ketones, acids, and alcohols, are also embedded in this product range. …

Effect Of Support, Preparations Methods, Ag Promotion And Nc Size On The Activity, Selectivity And Sintering Deactivation Of Supported Co Fischer-Tropsch Catalyst, Mahmood Rahmati

Theses and Dissertations

A series of silver-promoted, 20 wt% cobalt Fischer-Tropsch synthesis (FTS) catalysts supported on an alumina modified with 5 wt% silica were prepared using two methods: traditional incipient wetness impregnation (IWI) and a new solvent-deficient precipitation (SDP) technique. Catalysts containing silver promoter concentrations of 0.3, 0.6, 1.2, and 2.5 wt% were prepared using each of the two methods. Silver improved the reducibility of the cobalt significantly, lowering reduction temperatures by up to 100°C, and increasing the extent of reduction by up to 35%. Further, in both preparation methods, changing the silver loading altered the cobalt dispersion. The smallest Co crystallite size …

Synthesis And Applications Of Ceramic (Silicon Carbide And Silicon Nitride), Metallic (Cobalt(0)) And Polymeric (Polyurethane) Aerogels, Parwani M. Rewatkar

Doctoral Dissertations

"A new method has been demonstrated for the synthesis of monolithic ceramic and purely metallic aerogels from xerogel powder compacts, and the use of polyurethane aerogels based on cyclodextrins as efficient desiccants.

I. Highly porous ( > 80%) monolithic SiC and Si₃N₄, aerogels were prepared from compressed compacts of polyurea-crosslinked silica xerogel powders. The process is time efficient as solvent-exchange through powders is fast, and energy efficient as it bypasses drying with supercritical fluids. The final ceramic objects were chemically pure, sturdy, with compressive moduli at 37 ±7 MPa and 59 ± 7 MPa, and thermal conductivities …