Engineering Commons^™

Optimal Design Of Sound Absorbing Systems With Microperforated Panels, Nicholas Nakjoo Kim

Open Access Dissertations

As the development of technology makes economic prosperity and life more convenient, people now desire a higher quality of life. This quality of life is based not only on the convenience in their life but also on clean and eco-friendly environments. To meet that requirement, much research is being performed in many areas of eco-friendly technology, such as renewable energy, biodegradable content, and batteries for electronic vehicles.

This tendency is also obvious in the acoustics area, where there are continuing attempts to replace fiber-glass sound absorbers with fiber-free materials. The combination of microperfoated panels (MPP) (one of the fiber-free sound …

Energy Localization And Heat Generation In Composite Energetic Systems Under High-Frequency Mechanical Excitation, Jesus O. Mares

Open Access Dissertations

In this work, the ability to use high frequency mechanical excitation to generate significant heating within plastic bonded explosives, as well as single energetic particles embedded within a viscoelastic binder, is studied. In this work, the fundamental mechanisms associated with the conversion of high-frequency mechanical excitation to heat as applied to these composite energetic systems are thoroughly investigated.

High-frequency contact excitation has been used to generate a significant amount of heat within samples of PBX 9501 and representative inert mock materials. Surface temperature rises on the order of 10 °C were observed at certain frequencies over a range from 50 …

Implementing And Testing A Panel-Based Method For Modeling Acoustic Scattering From Cfd Input, S. Hales Swift

Open Access Dissertations

Exposure of sailors to high levels of noise in the aircraft carrier deck environment is a problem that has serious human and economic consequences. A variety of approaches to quieting exhausting jets from high-performance aircraft are undergoing development. However, testing of noise abatement solutions at full-scale may be prohibitively costly when many possible nozzle treatments are under consideration. A relatively efficient and accurate means of predicting the noise levels resulting from engine-quieting technologies at personnel locations is needed. This is complicated by the need to model both the direct and the scattered sound field in order to determine the resultant …

Efficient Modeling Of Sound Source Radiation In Free-Space And Room Environments, Yangfan Liu

Open Access Dissertations

Motivated by the need to develop efficient acoustics simulations for sources in different room environments, a modeling procedure has been proposed that consists of two steps in general: (1) the modeling of the free-space radiation of the source based on measurements in a anechoic environment, and (2) the prediction of the sound field in a room environment based on that free-space information.

To achieve a high modeling efficiency, i.e., to reduce the number of modeling parameters while still maintaining acceptable accuracy, a Multipole Equivalent Source Model (ESM) with undetermined source locations has been developed for the free-space sound field prediction. …

Particle Modeling Of Non-Equilibrium Field Emission Driven Rf Microplasmas, Siva Sashank Tholeti

Open Access Dissertations

Non-equilibrium microplasmas at atmospheric pressures have been investigated for active flow control, micropropulsion and electronic display applications to name a few. The operational voltages for these microplasmas are on the order of kilovolts. When the electric field at the electrodes reaches GV/m or tens of GV/m either due to reduced interelectrode spacing and surface irregularities or due to carefully designed nanostructures on the electrodes, quantum processes such as field emission and field ionization come into effect. These can potentially reduce the operational voltages of microplasma devices by an order of magnitude. Due to the rarefied and non-equilibrium nature of these …

Experimental Investigation And Numerical Simulation Of A Copper Micro-Channel Heat Exchanger With Hfe-7200 Working Fluid, Eric Borquist

Doctoral Dissertations

Ever increasing cost and consumption of global energy resources has inspired the development of energy harvesting techniques which increase system efficiency, sustainability, and environmental impact by using waste energy otherwise lost to the surroundings. As part of a larger effort to produce a multi-energy source prototype, this study focused on the fabrication and testing of a waste heat recovery micro-channel heat exchanger. Reducing cost and facility requirements were a priority for potential industry and commercial adoption of such energy harvesting devices. During development of the micro-channel heat exchanger, a new fabrication process using mature technologies was created that reduced cost, …

Design Of Three-Dimensional Near-Zero Refractive Index Metamaterials, David Flores Iii

Theses and Dissertations

Near-zero refractive index metamaterials exhibit remarkable electromagnetic properties which can and will be applied in the near future. From the known methods of achieving near-zero refractive index, this work primarily focuses on the design of 3D metamaterials whose permittivity and permeability are both close to zero while maintaining relatively low loss factor. The design of the metamaterials is based on the chiral shape “omega” and designed to weave periodically as a fishnet. Theoretical analysis, computer modeling and simulation are steps taken in the design of metamaterials. A computational tool based on the robust method for effective parameter extraction is successfully …

Preliminary Design Tools In Turbomachinery: Non-Uniformly Spaced Blade Rows, Multistage Interaction, Unsteady Radial Waves, And Propeller Horizontal-Axis Turbine Optimization, Yujun Leng

Open Access Dissertations

Turbomachinery flow fields are inherently unsteady and complex which makes the related CFD analyses computationally intensive. Physically based preliminary design tools are desirable for parametric studies early in the design stage, and to provide deep physical insight and a good starting point for the later CFD analyses. Four analytical/semi-analytical models are developed in this study: 1) a generalized flat plate cascade model for investigating the unsteady aerodynamics of a blade row with non-uniformly spaced blades; 2) a multistage interaction model for investigating rotor-stator interactions; 3) an analytical solution for quantifying the impeller wake convection and pressure wave propagating between a …