Engineering Commons^™

Study On The Use Of Mgal Hydrotalcites As Solid Heterogeneous Catalysts For Biodiesel Production, João F. Gomes

João F Gomes

This paper, reports experimental work on the use of new heterogeneous solid basic catalysts for biodiesel production: double oxides of Mg and Al, produced by calcination, at high temperature, of MgAl lamellar structures, the hydrotalcites (HT). The most suitable catalyst system studied are hydrotalcite Mg:Al 2:1 calcinated at 507 ºC and 700 ºC, leading to higher values of FAME also in the second reaction stage. One of the prepared catalysts resulted in 97.1 % Fatty acids methyl esters (FAME) in the 1st reaction step, 92.2 % FAME in the 2nd reaction step and 34 % FAME in the 3rd reaction …

Power Management For Gpu-Cpu Heterogeneous Systems, Xue Li

Masters Theses

In recent years, GPU-CPU heterogeneous architectures have been increasingly adopted in high performance computing, because of their capabilities of providing high computational throughput. However, current research focuses mainly on the performance aspects of GPU-CPU architectures, while improving the energy efficiency of such systems receives much less attention. There are few existing efforts that try to lower the energy consumption of GPU-CPU architectures, but they address either GPU or CPU in an isolated manner and thus cannot achieve maximized energy savings. In this paper, we propose GreenGPU, a holistic energy management framework for GPU-CPU heterogeneous architectures. Our solution features a two-tier …

Led Street Light Research Project, Donald K. Carter, Stephen Quick

Stephen Quick

The City of Pittsburgh planned to replace its existing 40,000 street lighting fixtures with LED fixtures and engaged the Remaking Cities Institute (RCI) to investigate the full range of potential benefits of a replacement program in business districts. The study team investigated the technological potentials offered by LED lighting, best management practices (BMP) in LED lighting and lessons learned from cities where LED lighting has been installed, as well as the place-making and aesthetic impact of LED lighting and associated technologies. The team also investigated issues raised by the use of LEDs as the light source and issues of replacing …

Notice On A Case Study On The Utilization Of Wind Energy Potential On A Remote And Isolated Small Wastewater Treatment Plant, João F. Gomes

João F Gomes

Small wastewater treatment plants (WWTP) are frequently located, by necessity, in remote and isolated sites, which increases the difficulty of its energy supply. Some of them are located near the seaside, in environmental sensible zones, and due to tourism activity of these sites, seasonal effects related with population size fluctuation can occur, which can originate certain inefficiencies concerning WWTP design and energy supply. The objective of this paper is to describe a step by step procedure for evaluation of the wind potential of sites that are dependent of in-situ energy generation, as well as, a case study on the utilization …

A Life Cycle Comparison Of Light-Frame Wood And Insulated Concrete Form Building Envelopes: Energy Use And Green House Gases, Sherman Authur Matthews

Masters Theses

Given the building sector’s substantial contribution to global energy use and green house gas (GHG) emissions, it is of great importance that only the most effective building envelopes are utilized. Conventional light-frame wood building envelopes are highly popular due to their ease of construction and building economy; however the life cycle performance of the building envelope is often overlooked when this selection is made. Although insulated concrete form (ICF) building envelopes generally require a substantially higher embodied energy input, it should be considered that improvements during a building’s operation phase can offers significant energy returns, ultimately reducing the building’s life …

Benefits Of Near-Term Cloud Location Forecasting For Large Solar Pv, Timothy Robert Rudd

Master's Theses

As the ‘green’ energy movement continues to gain momentum, photovoltaic generation is becoming an increasingly popular source for new power generation. The primary focus of this paper is to demonstrate the benefits of close-to real-time cloud sensing for Photovoltaic generation. In order to benefit from this close-to real-time data, a source of cloud cover information is necessary. This paper looks into the potential of point insolation sensors to determine overhead cloud coverage. A look into design considerations and economic challenges of implementing such a monitoring system is included. The benefits of cloud location sensing are examined using computer simulations to …

Wireless Embedded Smart Cameras: Performance Analysis And Their Application To Fall Detection For Eldercare., Alvaro Pinto

Department of Electrical and Computer Engineering: Dissertations, Theses, and Student Research

Wireless Embedded Smart Camera Networks has received a lot of attention from academia and industry because they are small in size and easy to deploy, and they offer a multitude of attractive applications. They can be used for embedded single unit applications, or can be networked for multi-camera applications.

We first analyze three different operation scenarios for a wireless vision sensor network wherein different levels of local processing is performed. A detailed quantitative comparison of three operation scenarios are presented in terms of energy consumption and latency. This quantitative analysis provides the motivation for performing high-level local processing and decision …

A Viability Study Of Photovoltaic Systems, Youakim Kalaani, William Nichols

Department of Electrical & Computer Engineering Faculty Research & Publications

Concerns over climate change and other environmental problems highlight a need for a shift toclean and renewable energy. The main objective of this study is to investigate the viability ofphotovoltaic electricity in the southeastern region of the United States. To achieve this goal, twocase studies were conducted involving a large retail store and a recreation center. Historical datarelated to weather conditions, solar energy and power demand were investigated and as a resultgrid-connected photovoltaic systems were designed to provide green energy for these facilities.Several engineering factors that went into the design process as well as economic andenvironmental considerations were thoroughly discussed …

An Environmental Economic Analysis Of Green Building And The Leadership In Energy And Environmental Design Rating System, John A. Manna

Honors Theses

Buildings account for over 70% of U.S. energy consumption and produce 30% of the nation’s greenhouse gas emissions. With growing concerns over future energy prices, the green building industry and the LEED rating system have made it their goal to produce better performing, more efficient buildings. LEED projects have been implemented in all 50 states, with 46 implementing LEED into public policy. In this study we evaluate the environmental and economic benefits of the LEED certification process. A cost-benefit analysis provides a framework for assessing the life cycle of a LEED building, incorporating both energy and cost savings, as well …

Improving The Energy Efficiency Of Fero House Home Of Alpha Delta Phi, Matt S. Stankiewicz

Honors Theses

As our country continues to grow and prosper we are faced with a growing number of environmental issues. While many of these issues were ignored in the pursuit of economic growth, we are now facing the harsh realities of our unmitigated expansion. The continual mining and use of fossil fuels has scarred our landscapes, polluted our air, and contaminated our waterways. Our nation’s greenhouse gas emissions are higher than ever and contributing heavily to global warming. With the United States’ population constantly on the rise and projected to hit 350 million in little over a decade1, it appears that our …

Irrigation System Components And Potentials For Energy Conservation, Charles M. Burt

BioResource and Agricultural Engineering

On-site electricity conservation in irrigation can be accomplished through a series of general steps. The primary focus of the agricultural energy conservation programs of the utilities has been to improve the efficiency of the pumping plant. In general, the electric utilities have provided or subsidized pump testing, along with some form of rebate for replacement or repair of pumps. There are, of course, other irrigation-related aspects of energy conservation. However, this report focuses on on-site electricity conservation in the field.

Energy Harvesting From Elliptical Machines Using Four-Switch Buck-Boost Topology, Alvin Jay Hilario

Master's Theses

This thesis presents the topic of using the Four-Switch Buck-Boost topology as a DC-DC converter for the Energy Harvesting from Elliptical Machines Project. The project works toward providing a modular synchronous power generation system. Due to the dynamic and sporadic output voltage and power characteristics of the Precor elliptical machine, the system requires a DC-DC converter as a voltage preregulator. The inherent wide input range, high efficiency, and low parts cost of this converter well suit the application. This paper further discusses other topologies and their shortcomings, as well as characterizes the Precor elliptical machine and Enphase Microinverter for interfacing. …

Agricultural Water Energy Efficiency: Final Report, Charles M. Burt, Dan J. Howes, Beau Freeman

BioResource and Agricultural Engineering

Beginning in 2007, the Irrigation Training and Research Center (ITRC) at California Polytechnic State University, San Luis Obispo, contracted with the California Energy Commission’s (CEC) Public Interest Energy Research (PIER) Program to undertake a large, multi-tiered study on agricultural water energy efficiency in California. The study was broken into the following research tasks: Task 1: Administrative; Task 2.1: Irrigation district energy survey; Task 2.2: Conversion to groundwater pumping with drip/ micro irrigation systems; Task 2.3: GIS-based water scheduling and software system; Task 3: Irrigation component energy analysis; Task 4: RD&D competitive solicitation; Task 5; Technology transfer. The resulting survey, research, …

A Study Into The Use Of Microprocessor Relays For Motor Operated Valve (Mov) Electrical Protection In Nuclear Power Plants, James Andrew Tuccillo

Master's Theses

Motor Operated Valves (MOVs) are electro-mechanical components used to isolate, divert, or introduce fluid flow. The use of microprocessor relays for actuator motor electrical protection within nuclear power plants is the focus of this thesis and is implemented by providing a new and enhanced protection scheme that provides the adequate conservatism necessary to ensure valve operation while still maintaining electrical safety and continued operational availability. The comprehensive protection scheme is designed around an advanced microprocessor relay that has the ability to simulate the thermal overload conditions of a motor operating into a destructive thermal region. Through laboratory testing, the validity …

Emergy As A Life Cycle Impact Assessment Indicator A Gold Mining Case Study, Wesley W. Ingwesen

United States Environmental Protection Agency: Staff Publications

Founded in thermodynamics and systems ecology, emergy evaluation is a method to associate a product with its dependencies on all upstream environmental and resource flows using a common unit of energy. Emergy is thus proposed as an indicator of aggregate resource use for life cycle assessment (LCA). An LCA of gold mining, based on an original life cycle inventory of a large gold mine in Peru, is used to demonstrate how emergy can be incorporated as an impact indicator into a process-based LCA model. The results demonstrate the usefulness of emergy in the LCA context. The adaptation of emergy evaluation, …

Modelling Net Zero Energy Options For A Sustainable Buildings Research Centre, Paul Cooper, Xiong Liu, Prabuono Buyung Kosasih, Rui Yan

Faculty of Engineering - Papers (Archive)

This paper describes the preliminary design and energy analysis of a university research building in NSW, Australia. This case study highlights some of the challenges confronting those wishing to design cost-effective net zero energy buildings in the Australian higher education sector and beyond. The Sustainable Buildings Research Centre (SBRC) is presently under development at the University of Wollongong and will be a unique building in the local region and an exemplar in respect of demonstration of a range of technical and operational means of reducing greenhouse emissions and other ecological impacts. This paper provides details on the constraints and opportunities …

Influence Of Temperature On Coal Sorption Characteristics And The Theory Of Coal Surface Free Energy, Lei Zhang, Najdat I. Aziz, Ting Ren, Zhongwei Wang

Faculty of Engineering - Papers (Archive)

An experimental study was undertaken to examine the sorption and desorption characteristics of coal at temperatures of 35 °C, 45 °C and 55 °C. The study focused on the effect of changes in temperature and coal particle sizes on gas sorption and desorption characteristics. The coal size used ranged from fragmented coals, 16 mm, 8 mm, 2.4 mm, powdered coal of 150 μm and 54 mm core samples. The samples were tested in pressure vessels, known as “bombs”, charged with CO2 gas at different pressure levels up to a maximum of 4000 kPa. It was found that temperature has a …

Octave Spanning Supercontinuum In An As2s3 Taper Using Ultralow Pump Pulse Energy, Darren D. Hudson, Stephen A. Dekker, Eric C. Magi, Alexander C. Judge, Stuart D. Jackson, Enbang Li, J S. Sanghera, L B. Shaw, I D. Aggarwal, Benjamin J. Eggleton

Faculty of Engineering and Information Sciences - Papers: Part A

An octave spanning spectrum is generated in an As2S3 taper via 77 pJ pulses from an ultrafast fiber laser. Using a previously developed tapering method, we construct a 1.3 μm taper that has a zero-dispersion wavelength around 1.4 μm . The low two-photon absorption of sulfide-based chalcogenide fiber allows for higher input powers than previous efforts in selenium-based chalcogenide tapered fibers. This higher power handling capability combined with input pulse chirp compensation allows an octave spanning spectrum to be generated directly from the taper using the unamplified laser output.

Energy-Loss Rate Of A Fast Particle In Graphene, Yee Sin Ang, Chao Zhang, Chun Kee

Faculty of Engineering - Papers (Archive)

The energy-loss rate of a fast particle in graphene is studied. The energy-loss rate always increases with increasing incident particle energy, which is quite unusual when compared to electron gas in normal metal. Graphene exhibits a “discriminating” behavior where there exists a low energy cut-off below which the scattering process is strictly forbidden, leading to lossless traverse of an external particle in graphene. This low energy cutoff is of the order of nearest neighbor hopping bandwidth. Our results suggest that backscattering is also absent in the external particle scattering of graphene.

The Carbon Footprint Associated With Water Management Policy Options In The Las Vegas Valley, Nevada, Eleeja Shrestha, Sajjad Ahmad, Walter Johnson, Jacimaria R. Batista

Civil and Environmental Engineering and Construction Faculty Research

A system dynamics model was developed to estimate the carbon dioxide (CO₂) emissions associated with conveyance of water from the water source to the distribution laterals of the Las Vegas Valley. In addition, the impact of several water management policies, including water conservation, reuse, and population growth rate change was evaluated. The results show that, at present, nearly 0.53 million metric tons of CO₂ emissions per year are released due to energy use for water conveyance in distribution laterals of the Valley from Lake Mead, located 32.2 km (20 miles) southeast of the Las Vegas at an …

Wireless Energy Transfer, Ryan Sasur

Electrical Engineering

Phones are now an integral component in the daily lives of people. Smartphones give access to movies, internet, and even books. This versatility and increased use can also lead to a shorter battery life. A phone with video viewing capabilities will be a heavy load on the unit’s battery. With phones utilizing 3G and 4G technology, even heavier demands are placed on the battery. As technology improves even further to provide for a larger entertainment experience on the phone, this could also lead to further battery degradation if the current battery situation isn’t addressed. To have a fully operational phone …

Working Active Power, Reflected Active Power, And Detrimental Active Power In The Power System, Tracy Nakamura Toups

LSU Master's Theses

Study of decomposition of the active power into components with deeper economical meanings, namely working active power, reflected active power, and detrimental active power is the subject of the thesis. The decomposition of active power will be based on the Current’s Physical Component (CPC) Theory. Working active power is equivalent to useful power that is the rate of energy used to do work, such as mechanical power. Reflected active power is the rate of energy transfer that the load sends back to the supply which dissipates off the supply resistance. This reflected active power is not taken into account on …

Energy Efficiency Technologies For Buildings: Potential For Energy, Cost, And Carbon Emission Savings, Bukola S. Jimoh

CMC Senior Theses

Buildings are a significant energy consumer and are responsible for an increasingly large percent of worldwide greenhouse gas emissions, currently between 30 and 40 percent. Energy efficiency presents unique opportunities for building owners to reduce their environmental footprint and add value through cost savings, tax deductions, and increased market value. An analysis of 183 samples of efficiency measures in seven technology categories found that 74% of efficiency investments had a positive net present value. Building automation system and chiller plant improvements had the highest mean energy and carbon dioxide savings per square foot. Additionally, building automation systems had, on average …

Investigation Into The Potential Use Of Windbreaks To Improve Solar Collector Performance, Michael Watts

All Graduate Theses, Dissertations, and Other Capstone Projects

The global demand for energy is ever increasing; however, the world has a limited number of fossil fuels available. Therefore, alternative renewable energy sources must be utilized. For this reason, solar thermal collectors have become an increasingly popular method for providing hot water or space heating. However, solar thermal collectors are most commonly used in areas that experience warm climates throughout the year. In areas that experience seasonal climates, the cold temperatures and harsh climate conditions significantly reduce the performance of solar thermal collectors during the winter months. This thesis examined the potential that the implementation of a windbreak could …