Open Access. Powered by Scholars. Published by Universities.®
- Discipline
- Institution
- Publication
- Publication Type
Articles 1 - 7 of 7
Full-Text Articles in Engineering
Response Of Ti-6al-4v And Ti-24al-11nb Alloys To Dry Sliding Wear Against Hardened Steel
Response Of Ti-6al-4v And Ti-24al-11nb Alloys To Dry Sliding Wear Against Hardened Steel
A.S. Md Abdul Haseeb
Titanium alloys have been of great interest in recent years because of their very attractive combination of high strength, low density and corrosion resistance. Application of these alloys in areas where wear resistance is also of importance calls for thorough investigations of their tribological properties. In this work, Ti-6Al-4V and Ti-24Al-11Nb alloys were subjected to dry sliding wear against hardened-steel counter bodies and their tribological response was investigated. A pin-on-disc type apparatus was used with a normal load of 15-45N and sliding speed of 1.88 ms -1. In the steady state, it was demonstrated that Ti-24Al-11Nb had a substantially higher …
Modeling Corrosion In Oxygen Controlled Lbe Systems With Coupling Of Chemical Kinetics And Hydrodynamics-Phase Two, Samir Moujaes, Yitung Chen
Modeling Corrosion In Oxygen Controlled Lbe Systems With Coupling Of Chemical Kinetics And Hydrodynamics-Phase Two, Samir Moujaes, Yitung Chen
Transmutation Sciences Materials (TRP)
The proposed work will combine chemical kinetics and hydrodynamics in target and test-loop lead-bismuth eutectic (LBE) systems to model system corrosion effects. This approach will result in a predicative tool that can be validated with corrosion test data, used to systematically design tests and interpret the results, and provide guidance for optimization in LBE system designs. The task includes two subtasks. The first subtask is to try to develop the necessary predictive tools to be able to predict the levels of oxygen and corrosion products close to the boundary layer through the use of Computational Fluid Dynamics (CFD) modeling. The …
Research Of Surface-Oxidation Epitaxy Of Nio Films On Cube Textured Ni Tapes, Dongqi Shi, Mihail Ionescu, Jeff Mckinnon, Wu Ming Chen, S. X. Dou
Research Of Surface-Oxidation Epitaxy Of Nio Films On Cube Textured Ni Tapes, Dongqi Shi, Mihail Ionescu, Jeff Mckinnon, Wu Ming Chen, S. X. Dou
Faculty of Engineering - Papers (Archive)
Thin films of NiO were fabricated in air by surface-oxidation epitaxy (SOE) on biaxially-textured Ni substrate, for use as buffer layers for YBCO coated conductors. The surface-oxidation conditions such as the temperature and the reaction time, as well as the cooling rate, playa determining role in the process of epitaxial growth of the NiO layer. A continuous, biaxially-aligned textured NiO layer, was obtained for a 10 min oxidation in air at 1120°C,and acooling rate of 150 Klh. The roughness of the NiO layer is mostly controlled by a coarsening of some NiO grains .
High Temperature Compression Testing Of An Advanced Carbon-Carbon Composite In An Oxidizing Atmosphere, Joshua C. Walls
High Temperature Compression Testing Of An Advanced Carbon-Carbon Composite In An Oxidizing Atmosphere, Joshua C. Walls
Electronic Theses and Dissertations
Compression testing of an advanced, three-dimensional weave, carbon-carbon composite was performed from room temperature to 2192°F (1200°C) in an oxidizing environment. The material tested is primarily used for missile nose cones and rocket nozzles. A test system and test method was developed for performing high temperature compression testing and techniques were developed for machining the material to minimize fiber damage and maintain accurate tolerances. Test specimens were cut from a block of the test material in the three principal fiber orientations, and off-axis tests were cut at 45" orientations to each principal fiber direction. The specimens were tested by direct …
Electrochemical Filtering Of Co From Fuel-Cell Reformate, Balasubramanian Lakshmanan, Wayne Huang, John W. Weidner
Electrochemical Filtering Of Co From Fuel-Cell Reformate, Balasubramanian Lakshmanan, Wayne Huang, John W. Weidner
Faculty Publications
A proton exchange membrane fuel cell was used as a flow reactor for continuous preferential oxidation of CO over H2 from 1.0% CO in H2 under pulse-potential control. By varying the pulse profile ~e.g., on-time, off-time, pulse potential! the CO and H2 oxidation currents were varied independently. The improvement in faradaic selectivity between CO and H2 oxidation results from the promotion of CO adsorption during the off ~i.e., open-circuit! portion of the pulse. Therefore, during the on portion CO oxidation was preferred while the surface was covered with CO.
Development Of A Novel Co Tolerant Proton Exchange Membrane Fuel Cell Anode, Andrew T. Haug, Ralph E. White, John W. Weidner, Wayne Huang
Development Of A Novel Co Tolerant Proton Exchange Membrane Fuel Cell Anode, Andrew T. Haug, Ralph E. White, John W. Weidner, Wayne Huang
Faculty Publications
Typically Pt is alloyed with metals such as Ru, Sn, or Mo to provide a more CO-tolerant, high-performance proton exchange membrane fuel cell (PEMFC) anode. In this work, a layer of carbon-supported Ru is placed between the Pt catalyst and the anode flow field to form a filter. When oxygen is added to the fuel stream, it was predicted that the slow H2 kinetics of Ru in this filter would become an advantage compared to Pt and Pt:Ru alloy anodes, allowing a greater percentage of O2 to oxidize adsorbed CO to CO2. With an anode feed …
Studies On Capacity Fade Of Spinel-Based Li-Ion Batteries, Ramadass Premanand, Anand Durairajan, Bala Haran, Ralph E. White, Branko N. Popov
Studies On Capacity Fade Of Spinel-Based Li-Ion Batteries, Ramadass Premanand, Anand Durairajan, Bala Haran, Ralph E. White, Branko N. Popov
Faculty Publications
The performance of Cell-Batt® Li-ion cells using nonstoichiometric spinel as the positive electrode material has been studied at different charging rates. The capacity of the cell was optimized based on varying the charging current and the end potential. Subsequent to this, the capacity fade of these batteries was studied at different charge currents. During cycling, cells were opened at intermittent cycles and extensive material and electrochemical characterization was done on the active material at both electrodes. For all charge currents, the resistance of both the electrodes does not vary significantly with cycling. This result is in contrast with cells …