Engineering Commons^™

Optimal Design Of Special High Torque Density Electric Machines Based On Electromagnetic Fea, Murat G. Kesgin

Theses and Dissertations--Electrical and Computer Engineering

Electric machines with high torque density are essential for many low-speed direct-drive systems, such as wind turbines, electric vehicles, and industrial automation. Permanent magnet (PM) machines that incorporate a magnetic gearing effect are particularly useful for these applications due to their potential for achieving extremely high torque density. However, when the number of rotor polarities is increased, there is a corresponding need to increase the number of stator slots and coils proportionally. This can result in manufacturing challenges. A new topology of an axial-flux vernier-type machine of MAGNUS type has been presented to address the mentioned limitation. These machines can …

Peer-To-Peer Energy Trading In Smart Residential Environment With User Behavioral Modeling, Ashutosh Timilsina

Theses and Dissertations--Computer Science

Electric power systems are transforming from a centralized unidirectional market to a decentralized open market. With this shift, the end-users have the possibility to actively participate in local energy exchanges, with or without the involvement of the main grid. Rapidly reducing prices for Renewable Energy Technologies (RETs), supported by their ease of installation and operation, with the facilitation of Electric Vehicles (EV) and Smart Grid (SG) technologies to make bidirectional flow of energy possible, has contributed to this changing landscape in the distribution side of the traditional power grid.

Trading energy among users in a decentralized fashion has been referred …

Electromagnetic Formation Control Using Frequency Multiplexing, Zahra Abbasi

Theses and Dissertations--Mechanical Engineering

This dissertation addresses control of relative positions and orientations of formation flying satellites using magnetic interactions. Electromagnetic formation flight (EMFF) is implemented, in which each satellite is equipped with a set of electromagnetic coils to generate an electromagnetic field. Traditional EMFF technique applies DC magnetic fields which lead to a nonlinear and highly coupled formation dynamics that allow for only position or orientation control of the satellites. We present a new frequency multiplexing method, which is a technique that uses multi-frequency sinusoidal controls, to approximately decouple the formation dynamics and to provide enough controls for both position and orientation control. …

Oxidation Pretreatment For Enhanced Leachability Of Rare Earth Elements From Bituminous Coal Sources, Tushar Gupta

Theses and Dissertations--Mining Engineering

Rare earth elements (REEs) are critical components in advanced electronics, clean energy technologies, and national energy and economic security. The global supply situation of these strategically valuable elements remains critical as the market is largely monopolistic. Thus, to alleviate the dependence on global imports, investments are being made in the research and development of innovative and cost-effective technologies for the indigenous processing and recovery of REEs from alternate sources that are cheap and abundant. Numerous research findings have identified potential benefits and proven the technological feasibility of extracting and selectively concentrating REEs from coal byproducts such as preparation plant rejects …

Research On Power System State Estimation Problems – Series-Compensated Transmission Line Parameter And Load Model Parameter Estimation, Yiqi Zhang

Theses and Dissertations--Electrical and Computer Engineering

Transmission line and load model parameters are essential inputs to power system modeling and simulation, control, protection, operation, optimization, and planning. These parameters usually vary over time or under different operating conditions. Thus, reliable estimation methods are desired to ensure the accuracy of those parameters. This research focuses on estimation for transmission line parameters and the ZIP load model. The proposed estimation methods can use both online measurements and historical data of a specified duration. The parameters of long transmission lines with different series-compensation configurations are estimated using linear methods and optimal estimators with bad data detection capability. Additionally, Kalman …

Reliability Assessment And Optimization Of Water Distribution Systems Explicitly Considering Isolation Valve Locations, Erika Hernandez Hernandez

Theses and Dissertations--Civil Engineering

Water distribution systems have changed the landscape of communities through two services: 1) providing water supply for domestic and industrial use, and 2) providing water required to fight fires. However, a substantial portion of the water infrastructure in the country, as many of other public assets built over 50 years ago, are now reaching the end of their useful life; which combined with rapid growth and changes in demographics have placed water distribution pipe networks at a state that requires revitalization. The aging infrastructure along with the growing threat of natural and man-made disruptions have led water utilities to place …

Design And Process Of 3d-Printed Parts Using Composite Theory, Jordan Garcia

Theses and Dissertations--Mechanical Engineering

3D printing is a revolutionary manufacturing method that allows the productions of engineering parts almost directly from modeling software on a computer. With 3D printing technology, future manufacturing could become vastly efficient. However, it is observed that the procedures used in 3D printing differ substantially among the printers and from those used in conventional manufacturing. In this thesis, the mechanical properties of engineering products fabricated by 3D printing were comprehensively evaluated and then compared with those made by conventional manufacturing. Three open-source 3D printers, i.e., the Flash Forge Dreamer, the Tevo Tornado, and the Prusa, were used to fabricate the …

Optimum Design Of Axial Flux Pm Machines Based On Electromagnetic 3d Fea, Narges Taran

Theses and Dissertations--Electrical and Computer Engineering

Axial flux permanent magnet (AFPM) machines have recently attracted significant attention due to several reasons, such as their specific form factor, potentially higher torque density and lower losses, feasibility of increasing the number of poles, and facilitating innovative machine structures for emerging applications. One such machine design, which has promising, high efficiency particularly at higher speeds, is of the coreless AFPM type and has been studied in the dissertation together with more conventional AFPM topologies that employ a ferromagnetic core.

A challenge in designing coreless AFPM machines is estimating the eddy current losses. This work proposes a new hybrid analytical …

Curricular Optimization: Solving For The Optimal Student Success Pathway, William G. Thompson-Arjona

Theses and Dissertations--Electrical and Computer Engineering

Considering the significant investment of higher education made by students and their families, graduating in a timely manner is of the utmost importance. Delay attributed to drop out or the retaking of a course adds cost and negatively affects a student’s academic progression. Considering this, it becomes paramount for institutions to focus on student success in relation to term scheduling.

Often overlooked, complexity of a course schedule may be one of the most important factors in whether or not a student successfully completes his or her degree. More often than not students entering an institution as a first time full …

Mathematical Modeling For Platform-Based Product Configuration Considering Total Life-Cycle Sustainability, Tian Lan

Theses and Dissertations--Mechanical Engineering

Many companies are using platform-based product designs to fulfill the requirements of customers while maintaining low cost. However, research that integrates sustainability into platform-based product design is still limited. Considering sustainability during platform-based design process is a challenge because the total life-cycle from pre-manufacturing, manufacturing and use to post-use stages as well as economic, environmental and societal performance in these stages must be considered. In this research, an approach for quantifying sustainability is introduced and a mathematical model is developed for identifying a more sustainable platform. Data from life-cycle assessment is used to quantify environmental factors; criteria from the Product …

Determination Of Explosive Energy Partition Values In Rock Blasting Through Small-Scale Testing, Joshua Calnan

Theses and Dissertations--Mining Engineering

Blasting is a critical part of most mining operations. The primary function of blasting is to fragment and move rock. For decades, attempts have been made at increasing the efficiency of blasting to reduce costs and increase production. Most of these attempts involve trial and error techniques that focus on changing a single output. These techniques are costly and time consuming and it has been shown that as one output is optimized other outputs move away from their optimum level. To truly optimize a blasting program, the transfer of explosive energy into individual components must be quantified. Explosive energy is …

Role Based Hedonic Games, Matthew Spradling

Theses and Dissertations--Computer Science

In the hedonic coalition formation game model Roles Based Hedonic Games (RBHG), agents view teams as compositions of available roles. An agent's utility for a partition is based upon which role she fulfills within the coalition and which additional roles are being fulfilled within the coalition. I consider optimization and stability problems for settings with variable power on the part of the central authority and on the part of the agents. I prove several of these problems to be NP-complete or coNP-complete. I introduce heuristic methods for approximating solutions for a variety of these hard problems. I validate heuristics on …

Estimating Passive Material Properties And Fiber Orientation In A Myocardial Infarction Through An Optimization Scheme Using Mri And Fe Simulation, Dimitri Mojsejenko

Theses and Dissertations--Mechanical Engineering

Myocardial infarctions induce a maladaptive ventricular remodeling process that independently contributes to heart failure. In order to develop effective treatments, it is necessary to understand the way and extent to which the heart undergoes remodeling over the course of healing. There have been few studies to produce any data on the in-vivo material properties of infarcts, and much less on the properties over the time course of healing. In this paper, the in-vivo passive material properties of an infarcted porcine model were estimated through a combined use of magnetic resonance imaging, catheterization, finite element modeling, and a genetic algorithm optimization …

A Metrics-Based Sustainability Assessment Of Cryogenic Machining Using Modeling And Optimization Of Process Performance, Tao Lu

Theses and Dissertations--Mechanical Engineering

The development of a sustainable manufacturing process requires a comprehensive evaluation method and fundamental understanding of the processes. Coolant application is a critical sustainability concern in the widely used machining process. Cryogenic machining is considered a candidate for sustainable coolant application. However, the lack of comprehensive evaluation methods leaves significant uncertainties about the overall sustainability performance of cryogenic machining. Also, the lack of practical application guidelines based on scientific understanding of the heat transfer mechanism in cryogenic machining limits the process optimization from achieving the most sustainable performance.

In this dissertation, based on a proposed Process Sustainability Index (ProcSI …

Experimental Investigation To Inform Optimal Configurations For Dynamic Near-Field Passive Uhf Rfid Systems, Donnie E. Proffitt Ii

Theses and Dissertations--Mechanical Engineering

RFID has been characterized as a “disruptive technology” that has the potential to revolutionize numerous key sectors. A key advantage of passive RFID applications is the ability to wirelessly transmit automatic identification and related information using very little power. This paper presents an experimental investigation to inform the optimal configuration for programming passive ultra-high frequency (UHF) RFID media in dynamic applications. Dynamic programming solutions must be designed around the tag’s functionality, the physical programming configuration and environment. In this investigation, we present a methodology to determine an optimal configuration to maximize the systems programming efficiency for dynamic applications.

Temperature And Strain Controlled Optimization Of Stabilization Of Polyacrylonitrile Precursor Fibers, Mark Parr Taylor

Theses and Dissertations--Mechanical Engineering

Carbon fiber is one of the leading materials for high strength and modulus, and light weight applications. Improvements in carbon fiber properties are directly dependent on all aspects of manufacture, especially the process of stabilization. Therefore, it is the goal of this thesis to study the effects of the temperature and strain profile of the stabilization process, and the resulting carbon fiber tensile properties. In addition, the precursor fibers used were spun under two different draw ratios, to study the effects of the spinning parameters. Results indicated through DMA studies that completeness of stabilization reactions can be gauged by the …

A Study Of Queuing Theory In Low To High Rework Environments With Process Availability, Adam J. Brown

Theses and Dissertations--Manufacturing Systems Engineering

In manufacturing systems subject to machine and operator resource constraints the effects of rework can be profound. High levels of rework burden the resources unnecessarily and as the utilization of these resources increases the expected queuing time of work in process increases exponentially. Queuing models can help managers to understand and control the effects of rework, but often this tool is overlooked in part because of concerns over accuracy in complex environments and/or the need for limiting assumptions. One aim of this work is to increase understanding of system variables on the accuracy of simple queuing models. A queuing model …

Economic Modeling & Optimization Of A Region Specific Multi-Feedstock Biorefinery Supply Chain, William H. Faulkner

Theses and Dissertations--Manufacturing Systems Engineering

The objective of this thesis is to include strategic and tactical level decisions into the biorefinery supply chain design for a specific region while comparing multiple conversion technologies and biomass feedstocks. The allocation of biomass feedstocks, products, and the respective supply chain configuration locations are determined while ensuring the regions monthly biomass availability and product market demand constraints are met. This research considers all actions required to bring the bio-based products to market from harvesting, storing, and processing the biomass to market distribution. Two different conversion technologies are chosen for comparison: one advanced conversion technology and one conventional technology. Potential …

Modeling And Optimization To Evaluate Sustainability Performance Of Customizable Product Service Systems, Ken Harsha Tilakaratne Wijekoon

University of Kentucky Master's Theses

The aim of this thesis is to present a new methodology to evaluate and optimize sustainability of customizable product-service systems while ensuring economic, environmental and societal constraints are also satisfied. Activities across the total product lifecycle are considered to develop a model that evaluates closed-loop flow, while being monitored through the growth, maturity and decline stages of the product to provide a comprehensive analysis. A novel method to evaluate the customer satisfaction is also presented. The research considers a modular product where customization can be achieved by selecting from alternatives while ensuring the compatibility between these alternatives. A manufacturer will …