Engineering Commons^™

Automated Multidisciplinary Optimizations Of Conceptual Rocket Fairings, Ronald S. Smart

Theses and Dissertations

The purpose of this research is to develop and architect a preliminary multidisciplinary design optimization (MDO) tool that creates multiple types of generalized rocket fairing models. These models are sized relative to input geometric models and are analyzed and optimized, taking into account the primary objectives, namely the structural, thermal, and aerodynamic aspects of standard rocket flights. A variety of standard nose cone shapes is used as optimization proof of concept examples, being sized and compared to determine optimal choices based on the input specifications, such as the rocket body geometry and the specified trajectory paths. Any input models can …

Analytical Modeling And Optimization Of A Thermoelectric Heat Conversion System Operating Betweeen Fluid Streams, Stephen H. Taylor

Theses and Dissertations

Analytical, closed-form solutions governing thermoelectric behavior are derived. An analytical model utilizing a thermal circuit is presented involving heat transfer into, through, out of, and around a thermoelectric device. A nondimensionalization of the model is presented. Linear heat transfer theory is applied to the model to obtain a series of closed form equations predicting net power output for the thermoelectric device. Fluid streams flowing through shrouded heat sinks with square pin fins are considered for the thermal pathways to and from the device. Heat transfer and pressure drop are characterized in a manner conducive to an analytical model using previously …

Minimizing Base Column Demands In Multi-Story Buckling Restrained Braced Frames Using Genetic Algorithms, Christopher Hiroshi Yeates

Theses and Dissertations

Most structural optimization procedures focus on minimizing the total volume of steel in an attempt to reduce overall costs. However, many other factors can have an effect on the overall cost of a structure. Base column demands in particular, can affect base plate sizes, anchorage, and foundation design. Researchers have found that present methods for estimating column demands are too conservative. Nonlinear time history analyzes were conducted on buckling-restrained braced frames of six heights. Optimized results were found considering three ductility constraints and two optimization objectives. The two optimization objectives were minimized total brace area and minimized base column demands. …

Methods To Streamline Laminate Composite Design, Analysis, And Optimization, Ammon Ikaika No Kapono Hepworth

Theses and Dissertations

Advanced composite materials have seen major market growth in recent years due to their high strength and low weight properties. These materials are often made using a process that creates a composite laminate by stacking several composite layers together. However, the design, analysis and optimization of laminate composite materials are often a labor intensive process when done manually. This thesis discusses CAD independent algorithms that are integrated into commercial CAD tools to streamline these processes. Methods have been developed to automatically create 3D ply geometry for a laminate composite lay-up, streamline the creation of a laminate composite finite element model …

Cad-Centric Dynamic Workflow Generation, Travis L. Kenworthy

Theses and Dissertations

CAD systems are important design tools that enable the designer to conceptualize, visualize, analyze, and manufacture a design (Shahin 2008). Although high-end CAD systems provide several built-in design applications, the users of CAD often select various custom or proprietary non-CAD analyses that constrain, optimize, or evaluate their designs. An efficient method is needed to perform trade studies from within the CAD environment. Methods have been developed to meet the challenges associated with this need. The methods have been implemented in a program, called the Process Integrator, which resides in a CAD system and allows the user to perform trade studies …

Product Family Design Using Smart Pareto Filters, Jonathan D. Yearsley

Theses and Dissertations

Product families are frequently used to provide consumers with a variety of appealing products and to help maintain reasonably low production costs for manufacturers. Three common objectives in the design of product families are used to balance the interests of both consumers and manufacturers. These objectives are to maximize (i) product performance, (ii) product distinctiveness as perceived by the consumer, and (iii) product commonality as seen by the manufacturer. In this thesis, three methods are introduced that use multiobjective optimization and Smart Pareto filtering to satisfy the three objectives of product family design. The methods are progressive in nature and …

Design Of A Three-Passage Low Reynolds Number Turbine Cascade With Periodic Flow Conditions, Daniel R. Rogers

Theses and Dissertations

A numerical method for modeling a low Reynolds number turbine blade, the L1M, is presented along with the pitfalls encountered. A laminar solution was confirmed to not accurately predict the flow features known in low Reynolds number turbine blade flow. Three fully turbulent models were then used to try to predict the separation and reattachment of the flow. These models were also found to be insufficient for transitioning flows. A domain was created to manually trip the laminar flow to turbulent flow using a predictive turbulence transition model. The trip in the domain introduced an instability in the flow field …

Optimization Constrained Cad Framework With Iso-Performing Design Generator, Kelly Eric Bowman

Theses and Dissertations

Design decisions have a large impact early in the design process. Optimization methods can help engineers improve their early decision making, however, design problems are often ill-posed for optimization at this early stage. This thesis develops engineering methods to use optimization during embodiment design, despite these difficulties. One common difficulty in designing mechanical systems is in handling the effects that design changes in one subsystem have on another. This is made more difficult in early engineering design, when design information is preliminary. Increased efforts have been made to use numerical optimization methods in early engineering design – because of the …

Parametric Optimization Design System For A Fluid Domain Assembly, Matthew Jackson Fisher

Theses and Dissertations

Automated solid modeling, integrated with computational fluid dynamics (CFD) and optimization of a 3D jet turbine engine has never been accomplished. This is due mainly to the computational power required, and the lack of associative parametric modeling tools and techniques necessary to adjust and optimize the design. As an example, the fluid domain of a simple household fan with three blades may contain 500,000 elements per blade passage. Therefore, a complete turbine engine that includes many stages, with sets of thirty or more blades each, will have hundreds of millions of elements. The fluid domains associated with each blade creates …

A Comparison Of Optimized Nonlinear Time History Analysis And The Equivalent Lateral Forces Method For Brace Design, Lukas Balling

Theses and Dissertations

This thesis presents the development of a design procedure for buckling-restrained braced frames (BRBF's). This procedure uses nonlinear time history analysis and a formal optimization algorithm. The time history analysis includes an elasto-plastic model for the braces. The optimization algorithm is a genetic algorithm. This procedure is referred to throughout the thesis as the "Nonlinear Time History Analysis Procedure with Optimization" (NTHO). Current design specifications for BRBF's are based on inelastic design spectra and approximate formulas for the determination of natural period. These spectra are used to obtain seismic base shear, and the distribution of equivalent lateral forces. Yielding and …

Autonomic Product Development Process Automation, John E. Daley

Theses and Dissertations

Market globalization and mass customization requirements are forcing companies towards automation of their product development processes. Many task-specific software solutions provide localized automation. Coordinating these local solutions to automate higher-level processes requires significant software maintenance costs due to the incompatibility of the software tools and the dynamic nature of the product development environment. Current automation methods do not provide the required level of flexibility to operate in this dynamic environment. An autonomic product development process automation strategy is proposed in order to provide a flexible, standardized approach to product development process automation and to significantly reduce the software maintenance costs …

Design And Fabrication Of Rotationally Tristable Compliant Mechanisms, Tyler M. Pendleton

Theses and Dissertations

The purpose of this research is to develop the tools necessary to create tristable compliant mechanisms; the work presents the creation of models and concepts for design and a demonstration of the feasibility of the designs through the fabrication of tristable compliant mechanism prototypes on the macro scale. Prior methods to achieve tristable mechanisms rely on detents, friction, or power input; disadvantages to these methods include a high number of parts, the necessity for lubrication, and wear. A compliant tristable mechanism accomplishes tristability through strain energy storage. These mechanisms would be preferable because of increased performance and cost savings due …

Percolation In Two-Dimensional Grain Boundary Structures And Polycrystal Property Closures, David T. Fullwood

Theses and Dissertations

The thesis addresses two topics in the study of material properties as determined by the microstructure. The first topic involves percolation as a tool in relating the grain boundary structure to global properties such as fracture and corrosion resistance. The second investigates optimization techniques in order to find the space of values that properties of a material can take, from consideration of the microstructure. In part I, the applicability of standard lattice percolation models to a random 2-D grain structure is explored. A random network based on the triangle lattice is proposed as a more appropriate model, and results in …

Developing A Design Space Model Using A Multidisciplinary Design Optimization Schema In A Product Lifecycle Management System To Capture Knowledge For Reuse, Nathaniel Luke Fife

Theses and Dissertations

Parametric strategies for design automation and optimization can have a big impact on engineering design. When parametric tasks and optimization frameworks and methods are combined, theses strategies can be used to make up what is known as a multidisciplinary design optimization (MDO) schema. Knowledge of a design space can be modeled by using a MDO schema to represent the design process. However, current MDO frameworks used to create this schema lack the scope to capture enterprise wide knowledge for reuse and collaboration. Concurrent with the development of MDO, many companies are moving toward increased use of product lifecycle management (PLM). …

Optimization Of Shape, Size, And Topology Design Variables In Trusses With A Genetic Algorithm, Kevin M. Gillman

Theses and Dissertations

Briggs' genetic algorithm was extended in the Gillman algorithm to include shape optimization of trusses. Other contributions include value representation, different member linking, alternate genes, automatic k-factor evaluation for buckling, and the option to prevent overlapping members. The purpose of these contributions was to make optimization using a genetic algorithm more accessible to design engineers. The Gillman algorithm was demonstrated in two original examples as well as an example from a published work. The Gillman algorithm was effective in finding lighter designs.

The Benefit Of Using Simulation To Improve The Implementation Of Lean Manufacturing Case Study: Quick Changeovers To Allow Level Loading Of The Assembly Line, Jack J. Mcclellan

Theses and Dissertations

In today's competitive manufacturing environment, companies are constantly looking for ways to improve. Because of this, many companies are striving to become "lean" by implementing lean manufacturing, which is a difficult process. To aid in the implementation of lean manufacturing, simulation was used to reduce the trial-and-error period of lean manufacturing and find to optimum approach to implement the lean manufacturing principle. In this research, a case study of implementing level loading of the production schedule for BullFrog International, L.C. will be examined. To make it possible to implement level loading, the thermo-former machine at the beginning of the operations …

Incorporating Functionally Graded Materials And Precipitation Hardening Into Microstructure Sensitive Design, Mark Edward Lyon

Theses and Dissertations

The methods of MSD are applied to the design of functionally graded materials. Analysis models are presented to allow the design of compliant derailleur for a case study and constraints are placed on the design. Several methods are presented for relating elements of the microstructure to the properties of the material, including Taylor yield theory, Hill elastic bounds, and precipitation hardening.

Applying n-point statistics to the MSD framework is also discussed. Some results are presented for the information content of the 2-point correlation statistics that follow from the methods used to integrate functionally graded materials into MSD.

For the compliant …