Engineering Commons^™

Strength, Fracture Evolution, And Permeability Changes From Confined Brazilian Tests On Sandstone, Tyler Louis Hagengruber

Civil Engineering ETDs

This research reports on confined Brazilian strength tests and concurrent permeability testing on sandstone. The majority of the tests measured permeability during loading to failure in the confined extension region. Additional testing includes unloading and reloading cycles to detect the development of microcracks and the dependence of permeability on mixed stress conditions. Further testing characterizes fracture networks by observing porosity changes due to microcrack interactions before peak load. All tests involve 5 cm diameter disk-shaped, jacketed samples that are subjected to confining stresses while they are diametrically loaded. Specially designed end caps allow for gas flow measurements. The test configuration …

Detection And Classification Of Vibrating Objects In Sar Images, Francisco German Perez Venegas

Electrical and Computer Engineering ETDs

The vibratory response of buildings and machines contains key information that can be exploited to infer their operating conditions and to diagnose failures. Furthermore, since vibration signatures observed from the exterior surfaces of structures are intrinsically linked to the type of machinery operating inside of them, the ability to monitor vibrations remotely can enable the detection and identification of the machinery.

This dissertation focuses on developing novel techniques for the detection and M-ary classification of vibrating objects in SAR images. The work performed in this dissertation is conducted around three central claims. First, the non-linear transformation that the micro-Doppler return …

Modeling And Simulation Of Damage In The Brazilian Indirect Tension Test Using The Finite-Discrete Element Method, Jeremiah C. Leyba

Civil Engineering ETDs

The Brazilian indirect tension test is used to investigate possible correlations between progressive damage and associated permeability changes. The test offers ease of replicability with a damage behavior known to lead to fracture openings as a tool for interpreting the indirect tensile strength of concrete and rocks. This behavior can lend insight into the nature of tensile damage and fracture progression in association with changes in permeability. The nature of these brittle materials is known to exhibit rapid failures in the Brazilian indirect tension test and require a method to retard the progression of damage for the possibility of acquiring …

Characterization And Modeling Of Asphalt Concrete For Dynamic Properties And Performances, A S M A. Rahman

Civil Engineering ETDs

The recently developed mechanistic-empirical pavement design guide (MEPDG, also known as Pavement M-E design method) uses the nationally calibrated, binder viscosity-based dynamic modulus predictive model for the design and analysis of asphalt pavements. In this study, this model is assessed for its appropriateness for asphalt-aggregate mixtures typically used in New Mexico. In essence, this study investigates the predictability issue of complex modulus of New Mexico mixes. A total of 54 Superpave mixes with different aggregate gradations, air voids, and binder grades were collected from the mixing plants and from the pavement construction sites. The loose asphalt mixtures were then compacted, …

Characterizing The Viscoelastic Behavior Of Pdms/Pdps Copolymers, Mark E. Small

Mechanical Engineering ETDs

Viscoelasticity is the property of materials that exhibits both viscous and elastic characteristics when undergoing deformation. In polymeric materials, the mechani- cal behavior is dominated by this viscoelastic phenomenon. Creating computational models for these materials can be quite complicated due to their frequency depen- dent and temperature dependent material properties. The research presented in this paper will use state of the art methods to fully develop a material model for a filled polydimethylsiloxane-polydiphenynlsiloxane (PDMS/PDPS) copolymer foam that has yet to be characterized. Mechanical properties of PDMS/PDPS copoly- mers are currently being studied to assess engineering performance, and to provide accurate …

Optimized Sizing And Placing Of Distributed Energy Resources (Ders) In An Island Microgrid Using Der-Cam, Bhuwan B. Bastola

Electrical and Computer Engineering ETDs

The electric grid at La Gomera, an island in the Canary archipelago, has been the subject of interest in optimized integration of Distributed Energy Resources (DERs) primarily because of high distribution losses and concerns about complying with emission regulations. Consequently, the utility that operates the island power system wishes to mitigate the problem with installation of renewable and distributed energy sources like PV and battery, which is the focus of this research.

Specifically, the focus of this thesis is to use Distributed Energy Resource - Customer Adoption Model (DER-CAM) to optimize the installation of PV and battery in terms of …