Engineering Commons^™

Design And Development Of The Portable Build Platform And Heated Travel Envelope For The Multi3d Manufacturing System, Steven Daniel Ambriz

Open Access Theses & Dissertations

The final product functionality of parts produced by Additive Manufacturing (AM) can, in part, be improved by the inclusion of multi-material capabilities. The “Multi3D system” that is under development at The University of Texas at El Paso uses material extrusion printing (or fused deposition modeling), solid conductor wire embedding, direct-write, component placement, and micromaching to enable multi-material fabrication. The Multi3D was designed to transport a workpiece between manufacturing stations via a six-axis robot, portable build platform (PBP), and a controlled temperature environment or chamber that travels to each manufacturing station. The heated travel envelope (HTE) was included to mitigate thermal …

Frequency Selective Surfaces For Extreme Applications, Jay Houston Barton

Open Access Theses & Dissertations

It is known that for high-power microwaves and other extreme environments, the use of resonant metallic elements in frequency selective surfaces can be problematic. The solution developed within this Dissertation to solve these problems was to use guided-mode resonance phenomenon to create all-dielectric frequency selective surfaces that could survive these extreme environments.

To fully understand how these devices work, three different computational electromagnetic methods are formulated and implemented. The formulation of these methods start with the differential form of Maxwellâ??s equation and are derived all the way down to the final simulation state. This is done sequentially and all the …

Growth And Analysis Of Micro And Nano Cdte Arrays For Solar Cell Applications, Brandon Adrian Aguirre

Open Access Theses & Dissertations

CdTe is an excellent material for infrared detectors and photovoltaic applications. The efficiency of CdTe/CdS solar cells has increased very rapidly in the last 3 years to ~20% but is still below the maximum theoretical value of 30%. Although the short-circuit current density is close to its maximum of 30 mA/cm2, the open circuit voltage has potential to be increased further to over 1 Volt. The main limitation that prevents further increase in the open-circuit voltage and therefore efficiency is the high defect density in the CdTe absorber layer. Reducing the defect density will increase the open-circuit voltage above 1 …

Combustion Synthesis Of Molybdenum Silicides And Borosilicides For Ultrahigh-Temperature Structural Applications, Mohammad Shafiul Alam

Open Access Theses & Dissertations

Molybdenum silicides and borosilicides are promising structural materials for gas-turbine power plants. A major challenge, however, is to simultaneously achieve high oxidation resistance and acceptable mechanical properties at high temperatures. For example, molybdenum disilicide (MoSi₂) has excellent oxidation resistance and poor mechanical properties, while Mo-rich silicides such as Mo₅Si₃ (called T₁) have much better mechanical properties but poor oxidation resistance. One approach is based on the fabrication of MoSi₂−T₁ composites that combine high oxidation resistance of MoSi₂ and good mechanical properties of T₁. Another approach involves the …

Characterization Of W-Ti-O Thin Films For Application In Photovoltaics, Amanda Patricia Christmas

Open Access Theses & Dissertations

Photovoltaic (PV) devices consist of the conversion of light energy into electricity. Nearly all PV technologies employ transparent conducting oxides (TCO) as an integral part of the de-vice structure so that the light can reach the semiconductor. The predominant transparent conducting oxide (TCO) that is currently being used in industry is indium tin oxide (ITO). However, Indium (In) is high in cost and becoming scarce in the world. This work is focused towards Titanium doped Tungsten oxide (WO3) for TCO application. The ultimate goal is making novel, cheaper, and efficient TCOs based on W-Ti-O films. Titanium will enhance the conductivity …

Experimental Studies Of Lox/Ch4 Uni-Element Shear Coaxial Injector Geometry, Vanessa Dorado-Martinez

Open Access Theses & Dissertations

The Center for Space Exploration Technology Research (cSETR) has developed a set of shear coaxial injectors as part of a system-level approach to study LOX/CH4 combustion. This Thesis describes the experimental studies involved in the characterization of the effects produced by two design injection face plate variables: post thickness and recession length. A testing program was developed to study the injectors' atomization process using LN2 as a substitute for LOX in cold flow and the flame anchoring mechanisms in hot firings. The cold flow testing stage was conducted to obtain liquid core measurements and compare its behavior between the different …

Integrated Sustainability Decision-Making Framework, Michael Paul Cole

Open Access Theses & Dissertations

The Integrated Sustainability Decision-Making Framework (ISDMF) is an 'ideal case' framework developed at the University of Texas El Paso (UTEP) from 2012 to present to provide the most comprehensive and concise sustainability strategy and decision-making template available.

Sustainable decision-making improves community Quality of Life, but is often beyond the reach of the majority. A framework that is most approachable, actionable, and adoptable can accelerate convergence on and continued operation of a sustainable solution. Research confirms that published frameworks continuously emerge, and are infinite in number. Iterations benefit from prior work, and contribution occurs when an 'ideal case' is envisioned, best …

Optimized Integrated Software Package For Classification Of Small Airway Dysfunction Using Genetic Algorithms, Elias Estrada

Open Access Theses & Dissertations

Due to the similarity in the symptoms of respiratory disorders, an accurate diagnosis could be a difficult task. Regarding asthma as the main focus of this research, early detection of small airway impairment could represent a better opportunity for timely diagnosis. An integrated software package (ISP) based on the impulse oscillometry technique, has been developed to serve as an important tool for clinicians during classification of asthma severities on children [1]. The current version of the ISP was tested with data obtained during several years by Dr. Homer Nazeran and Dr. Michael Goldman from 110 Hispanic children [2], providing an …

3d Printed Electromagnetic Transmission And Electronic Structures Fabricated On A Single Platform Using Advanced Process Integration Techniques, Paul I. Deffenbaugh

Open Access Theses & Dissertations

3D printing has garnered immense attention from many fields including in-office rapid prototyping of mechanical parts, outer-space satellite replication, garage functional firearm manufacture, and NASA rocket engine component fabrication. 3D printing allows increased design flexibility in the fabrication of electronics, microwave circuits and wireless antennas and has reached a level of maturity which allows functional parts to be printed. Much more work is necessary in order to perfect the processes of 3D printed electronics especially in the area of automation. Chapter 1 shows several finished prototypes of 3D printed electronics as well as newly developed techniques in fabrication. Little is …

Gadolinia Doped Hafnia (Gd2o3- Hfo2) Thermal Barrier Coatings For Gas Turbine Applications, Satya Kiran Gullapalli

Open Access Theses & Dissertations

Thermal efficiency of the gas turbines is influenced by the operating temperature of the hot gas path components. The material used for the hot gas path components can only withstand temperature up to a certain limit. Thermal barrier coatings (TBC) provide the additional thermal protection for these components and help the gas turbine achieve higher firing temperatures. Traditionally available yttria stabilized zirconia (YSZ) TBCs have a limitation up to 1200 C due to their phase transformation. The present work focuses on gadolinia based hafnia (GSH) TBCs to study their potential to replace the YSZ coatings. Different compositions of gadolinia doped …

Experimental Investigation Of Syngas Flame Stability Using A Multi-Tube Fuel Injector In A High Pressure Combustor, Sergio Elzar Maldonado

Open Access Theses & Dissertations

Over 92% of the coal consumed by power plants is used to generate electricity in the United States (U.S.). The U.S. has the world's largest recoverable reserves of coal, it is estimated that reserves of coal will last more than 200 years based in current production and demand levels. Integrated Gasification Combined Cycle (IGCC) power plants aim to reduce the amount of pollutants by gasifying coal and producing synThesis gas. SynThesis gas, also known as syngas, is a product of coal gasification and can be used in gas turbines for energy production. Syngas is primarily a mixture of hydrogen and …

Optimization Of Uv-Led Curable Printing Material For Applications In Direct Writing Systems: Inkjet, Reverse Offset, And Micro Dispensing Gpd, Ada Judith Ortega Varela

Open Access Theses & Dissertations

The quality of a product fabricated by direct writing methods will depend greatly on the properties of the printing material and its compatibility with the printing process. Although multiple advances in developing printing inks and pastes with novel properties are being made, the potential those can bring to electronics is hindered by their stability and performance during the printing process. In this study a UV-LED curable acrylic material was used to test the optimization of inks and pastes for three of the most common direct writing systems: Piezo-type Inkjet, Reverse Offset Roll to Plate, and Micro Deposition. The viscosity of …

Design And Evaluation Of A High Temperature/Pressure Supercritical Carbon Dioxide Direct Tubular Receiver For Concentrating Solar Power Applications, Jesus Daniel Ortega

Open Access Theses & Dissertations

This work focuses on the development of a solar power thermal receiver for a supercritical-carbon dioxide (sCO2), Brayton power-cycle to produce ~1 MWe. Closed-loop sCO2 Brayton cycles are being evaluated in combination with concentrating solar power to provide higher thermal-to-electric conversion efficiencies relative to conventional steam Rankine cycles. High temperatures (923 - 973 K) and pressures (20 - 25 MPa) are required in the solar receiver to achieve thermal efficiencies of ~50%, making concentrating solar power (CSP) technologies a competitive alternative to current power generation methods. In this study, the CSP receiver is required to achieve an outlet temperature of …

Water Recovery From Silica Saturated Ro Concentrate By The Concentrate Enhanced Reverse Osmosis Process, Gautam Patwardhan

Open Access Theses & Dissertations

Membrane fouling due to silica precipitation during reverse osmosis (RO) continues to be documented as the most common challenge in attaining stable continuous operation of RO systems across water treatment plants (1). Silica scale precipitation is time dependent and involves multiple steps leading to aqueous polymerization, condensation of polymers to form colloids, and deposition onto a solid surface (2). Exceeding the solubility of silica, widely considered to be in the range of 100-140 ppm, under a pH of 8 at 25 °C by various researchers, results in the precipitation of silica on the membranes, thereby limiting water recovery. Once the …

Design And Development Of Implantable And Remote Controlled Distraction Osteogenesis Device For Limb Lengthening Practice In Children, Mario Eduardo Rodriguez De La O

Open Access Theses & Dissertations

Recent technology improvements have been positively affecting medical industry in recent years since procedures and equipment are more precise and reliable. Nevertheless, there are still surgical procedures and medical devices that not fully address specific needs according to medical experts. One of those necessities is focused on options available for children patients when subjected to a surgical procedure named distraction osteogenesis. In general, distraction osteogenesis is performed when skeletal deformities need to be corrected or when bone lengthening is required, typically a mechanism is utilized to elongate bone at a controlled rate. The existing osteodistraction methods for limb lengthening and …

Master's In Electrical Engineering, Ricardo Xavier Rodriguez

Open Access Theses & Dissertations

This project is a focus on characterizing the process for actualizing three dimensional structures out of a carbon nanostructure composite via a direct print additive manufacturing process. Manufacturing parts additively enables for realization of geometrically complex shapes that often times cannot be manufactured any other way. The specificity of a material's properties have to be such, that the processing method can precisely place and bond material to itself in a highly repeatable manner. Commercial materials for additive manufacturing are have been optimized with these goals in mind and, therefore, often times lack the rigor and robustness for many applications.

The …

Modeling And Simulation Of A Lead-Free Active Structural Fiber For Multifunctional Composites, Linda Vera

Open Access Theses & Dissertations

Piezoelectric materials are widely used in a many areas of science and technology due to their unique electromechanical properties. The transformation of mechanical energy into electrical energy and vice versa caused by the piezoelectric effect has led to the development of piezoelectric sensor devices and actuators used in accelerometers, pressure and vibration meters, micropositioning devices, ultrasound generators, structural health monitoring, etc.

The most used piezoelectric material to this day is lead zirconate titanate PbZrO3-PbTiO3 (PZT) because of its high piezoelectric coefficient and Curie temperature, which allows it to be used in a more wide variety of applications. However, the commercial …

Design Optimization Of The Heat Transfer Model For A High Heat Flux Test Facility, Linda Hyemin Yoon

Open Access Theses & Dissertations

There are a variety of fuels that are utilized for space applications and in recent years, environmentally friendly fuels have been of interest. In the case of bipropellant rocket systems, hydrocarbon fuels have come to the attention of scientists and engineers. In particular, liquid methane was of interest in this study because of its physical and chemical advantages over other fuels, such as liquid hydrogen. Rocket engines rise to very high temperatures and to avoid catastrophic mechanical failure, a cooling system must be implemented within the engine to cool the walls. To get a better understanding of the fluid flow …

Natural Selectivity Of Nickel And Vanadium In Crude Oil, Olienka P. De La O Fernandez

Open Access Theses & Dissertations

Nickel and Vanadium have always been found in crude oil all around the world. The metal content is found mainly in porphyrin structures in the asphaltene fraction of the petroleum. In order to determine the reason for this natural preference, a set of experiments testing thermodynamics, kinetics, and other factors were performed. Candidate metalloporphyrins containing Vanadyl, Chromium, Iron, Nickel, Copper and Zinc were analyzed through chemical reactions characterized using Silica Column Chromatography, HPLC, MS and UV-Visible. Theoretical analysis of the stability of metalloporphyrins was conducted using DFT/NRLMOL for computational calculation. The analysis of all factors leads us to conclude that …

Safety Measures For Trucks: A Comparison Between Eu And U.S., Jan Kapusta

Open Access Theses & Dissertations

Road transportation is playing an important role in almost all of the freight movements and contributes to the economy. It has the highest share in the modal division of transported goods. This situation is not about to change in next years to come. Therefore, it is necessary to change the current situation and create rules and regulations that would lead to decrease in number of accidents either in EU or in U.S. The goal of this research is to analyze selected parameters related to the safety of truck transportation in EU and in U.S. This thesis also identifies and compares …

Alkali Promoted Molybdenum (Iv) Sulfide Based Catalysts, Development And Characterization For Alcohol Synthesis From Carbon Monoxide And Hydrogen, Belinda Delilah Molina

Open Access Theses & Dissertations

For more than a century transition metal sulfides (TMS) have been the anchor of hydro-processing fuels and upgrading bitumen and coal in refineries worldwide. As oil supplies dwindle and environmental laws become more stringent, there is a greater need for cleaner alternative fuels and/or synthetic fuels. The depletion of oil reserves and a rapidly increasing energy demand worldwide, together with the interest to reduce dependence on foreign oil makes alcohol production for fuels and chemicals via the Fischer Tropsch synthesis (FTS) very attractive. The original Fischer-Tropsch (FT) reaction is the heart of all gas-to-liquid technologies; it creates higher alcohols and …

Use Of Cosine Modulated Filter Bank To Quantify Human Muscle Fatigue Using Electromyography Signals Obtained During Isometric Voluntary Contractions, Liza Stephanie Rodriguez

Open Access Theses & Dissertations

As technology continues to advance, there continues to be an interest in applying engineering theories to solve medical problems. Technology has allowed researchers to investigate the properties and characteristics of the human body in hopes of emulating their complexities. The rising interest in the study of biopotentials for use in prosthetic limbs, exoskeletons and machine interfacing has led to a necessity to validate that the understanding of these signals is accurate. The study of biopotentials generated by muscles via a method known as electromyography (EMG) has improved the understanding of effects of rehabilitative treatments, assisted in diagnosing diseases, control of …

Effect Of Multi-Tube Injector Geometry On Flame Stability And Nox Emission In A High Pressure Gas Turbine Combustor, Sudipa Sarker

Open Access Theses & Dissertations

Future generation gas turbine combustors for power production are expected to have the capability of operating on high hydrogen content fuels. To ensure the implementation of high hydrogen content (HHC) fuel in a power generation unit without negotiating with operational or emission advantages, the study of the flame stability regime and behavior of (HHC) fuel under gas turbine condition leads to the necessity of the development of an optically accessible high-pressure combustor. This Dissertation first presents the design of an optically high-pressure combustor facility based on 500 kW power and 1.5 MPa pressure which is the representative pressure of a …

A Robust Algorithm For Estimating The Balance Of Autonomic Nervous System With Application To Mental Fatigue Detection Using Photoplethysmographic (Ppg) Signals, Ajay Kumar Verma

Open Access Theses & Dissertations

Spectral- and time-domain analysis of Heart Rate Variability (HRV) signal is widely used as a quantitative marker of the Autonomic Nervous System (ANS) activity. A robust algorithm was developed to derive HRV from photoplethysmographic (PPG) signals, to compute FFT- and AR-based spectra of these HRV signals, and to determine time- and frequency-domain features. This algorithm has detrending, sample-rate reductions, false-peak removal, automatic peak detection, peak-to-peak (P-P) interval detection and correction, time-domain feature extraction, HRV signal generation, and spectral-domain feature extraction from the HRV signal. Adapting to the very low spectral contents of the input PPG signal is very helpful in …

3d Printed Spatially Variant Anisotropic Metamaterials, Cesar Roman Garcia

Open Access Theses & Dissertations

The recent advancement in 3D printing has created a new way to design electronics and electromagnetic devices. This allows for a new breed of non-planar designs to be used, fully exploiting all three dimensions like never before. More functions can be fit into the same amount of space, products with novel form factors can be more easily manufactured, interconnects can be routed more smoothly, interfaces can be better implemented, electrical and mechanical functions can be comingled, and entirely new device paradigms will be invented. When departing from traditional planar topologies many new problems arise like signal integrity, crosstalk, noise, and …

Evaluation Of A Torch Ignition System For Propulsion, Robert Ellis

Open Access Theses & Dissertations

In recent years NASA has had a renewed interest in oxygen and methane as propellants for propulsion. The drive for this combination comes from several factors including ease of land- based storage, handling safety, in situ resource utilization, and a relatively clean burning process when compared with the widely used hypergolic propellants. This project is part of a larger goal of the Center for Space Exploration Technology Research (cSETR) to better understand all aspects of using LOX/CH4 propellants to create future hardware that is specially optimized for these propellants. This paper discusses the literature background and reasons that led to …

3d Printing Technology Using High Viscous Materials-Synthesis Of Functional Materials And Fabrication Of 3d Metal Structure, Seongik Hong

Open Access Theses & Dissertations

In the 3D printing technology, the research for using various materials has been performing. In this research work, 3D printable high viscous materials are suggested as one of the solutions for problems in the traditional 3D printing technology.

First, Cu-Ag coreshell was synthesized as a functional material. In terms of the reaction rate, reaction rate limiting step was defined as a fundamental research, and then prepared Cu-Ag coreshell was printed and analyzed. Second, the high viscous Cu paste was prepared and then metal 3D printed structure was fabricated by using new printing method.

In the synThesis of Cu-Ag coreshell, different …

Decision Making Model For Foreign Object Debris/Damage (Fod) Elimination In Aeronautics Using Quantitative Modeling Approach, Jose Jaime Lafon

Open Access Theses & Dissertations

(FOD) Foreign Object Debris/Damage has been a costly issue for the commercial and military aircraft manufacturers at their production lines every day. FOD can put pilots, passengers and other crews' lives into high-risk. FOD refers to any type of foreign object, particle, debris or agent in the manufacturing environment, which could contaminate/damage the product or otherwise undermine quality standards. Nowadays, FOD is currently addressed with prevention programs, elimination techniques, and designation of FOD areas, controlled access to FOD areas, restrictions of personal items entering designated areas, tool accountability, etc. All of the efforts mentioned before, have not shown a significant …

An Experimental Investigation Of The Cooling Channel Geometry Effects On The Internal Forced Convection Of Liquid Methane, Adrian Trejo

Open Access Theses & Dissertations

Rocket engine fuel alternatives have been an area of discussion for use in high performance engines and deep spaceflight missions. In particular, LCH4 has showed promise as an alternative option in regeneratively cooled rocket engines due to its non-toxic nature, similar storage temperatures to liquid oxygen, and its potential as an in situ resource. However, data pertaining to the heat transfer characteristics of LCH4 is limited. For this reason, a High Heat Transfer Test Facility (HHTTF) at the University of Texas at El Paso's (UTEP) Center for Space Exploration Technology and Research has been developed for the purpose of flowing …

Cell Releasing System Using Light Responsive Photovoltaic Devices, Mohammod Khairul Kabir Bhuyan

Open Access Theses & Dissertations

Tissue and organ regeneration via transplantation of cell bodies in-situ has become an emerging strategy in regenerative medicine. Injected or implanted cells must be available in large enough numbers and suitable delivery methods must be found especially when implantation into the affected tissue is not possible. In addition, better understanding of how to mitigate the inflammatory reactions and how to degrade the cell carriers are needed. Current cell-based therapies are limited to injection or implantation of cell suspensions or implantation of cell sheets. Development of alternative systems to obtain cell sheets or other functional cellular structures are required. We are …