Engineering Commons^™

Optimization Of Rfid System Coverage In A Manufacturing Environment, Scott D. Malatesta

Master's Theses

This paper compiles existing ideas, theories, and experiments across multiple disciplines to provide guidance for a company looking to implement an optimal RFID system in their production facility. The desire is to maximize the information received by the system while minimizing the cost. Four potential layouts of RFID antennas, two with overlapping antenna coverage and two with non-overlapping layouts, are first analyzed to understand the special coverage and the number of antennas required. The value of information is then quantified to determine whether higher coverage layouts are worth the additional costs associated with the higher number of antennas required. It …

Effect Of Low Velocity Impact On The Vibrational Behavior Of A Composite Wing, Richard M. De Luna

Master's Theses

Impact strength is one of the most important structural properties for a designer to consider, but it is often the most difficult to quantify or measure. A major concern for composite structures in the field is the effect of foreign objects striking composites because the damage is often undetectable by visual inspection. The objective for this study was to determine the effectiveness of using dynamic testing to identify the existence of damage in a small scale composite wing design. Four different impact locations were tested with three specimens per location for a total of 12 wings manufactured. The different impact …

Analysis Of Compression Creep Deformation Of 7050 Aluminum Large Scale Open Die Forgings During The Solution Heat Treatment Process, Ashley Lopez, Elysha Cole

Materials Engineering

A stress, ranging from 104.17 to 166.67 psi, was applied to 0.5 in diameter cylindrical samples of 7050 aluminum using a manufactured fixture that applies stress using an indenter with a diameter of 0.127 in. The stress range used replicates the stresses produced on large scale forgings weighing up to 4000 lbs. We chose a maximum, medium and low stress as our stress parameters. The samples were placed into the fixture for stability then placed in a furnace heated to 890°F which is the solution heat treatment temperature for 7050 aluminum. The heat treatment times varied between 4 and 24 …

Transcatheter Heart Valve Subassembly Device, Adam Aslam, Matthew Bezkrovny, Daniel Degree

Mechanical Engineering

No abstract provided.

Wasco Environmental Chamber System Manifold, Steve Mark Yatco

Industrial and Manufacturing Engineering

This report details the process of designing and producing a manifold that connects ultra-high purity (UHP) pressure and vacuum switches to an air supply so that the parts may be tested in an environmental chamber. Using the DMAIC (define, measure, analyze, improve, and control) methodology of problem solving, progress on the project includes thorough research about the problem, preliminary design solutions, iterative prototyping, and testing specific functionalities. Manufacturing engineering topics of tooling, fixturing, metrology, quality, and machining with manual and computer numerical control (CNC) varieties of both mills and lathes are applied during the course of the project. The report …

Modification Of A Draw Bar Type Arena Harrow To Three Point Mounted Type Harrow, Clayton Alan Brown

BioResource and Agricultural Engineering

This senior project will be the design, and construction of a three point hitch to be attached to a draw bar type spike tooth harrow. Currently used by the Cal Poly Rodeo Team to cultivate their arena before performances, and practices.

The attachment will allow the harrow to be pulled in both directions to create different types of soil affects.

Also the fabrications has a minimal budget so the majority of the materials will be scrap material already in position of the rodeo team or donated to the project.

Formula Sae Hybrid Carbon Fiber Monocoque / Steel Tube Frame Chassis, Matthew Hagan, John Rappolt, John Waldrop

Mechanical Engineering

The Cal Poly Formula SAE Team created this project in order to design and fabricate a high-performance chassis which would be competitive at 2013 FSAE Lincoln, and to document the process so that future teams could more easily create a chassis. One of the main goals was to reduce weight from the 143- lb 2012 chassis subsystem. A weight of 95 lb was achieved, with 82 lb in the chassis structure itself and a predicted torsional stiffness of 1700 lb*ft/deg. Composite materials design and manufacturing techniques were developed during the project. Design, testing, and manufacturing processes are detailed, and results …

The Collapsible Trailer: Design And Manufacture, Robert Hobson

Biomedical Engineering

No abstract provided.

S&G Metal Fab Battery Tray, Matthew Nartatez

Industrial and Manufacturing Engineering

This report was written for the design of a battery tray and manufacturing process for S&G Metal Fab. The manufacturing steps of how to process the sheet metal to create the product are defined and documented in this report. This project began with constraints given by S&G and were all accomplished using coursework knowledge obtained as a manufacturing engineer student at Cal Poly San Luis Obispo. This report mainly covers parameters regarding the cutting, bending and, deforming of sheet metal to acquire the desired shapes and sizes. It also analyzes the costs that are associated with these processes and material. …

The Design, Testing, And Manufacturing Of A Pin Fin Extrusion Heat Sink, Arash Michael Mira

Industrial and Manufacturing Engineering

My senior project focuses on the design, testing, and manufacturing of pin fin extrusion heat sinks that are you used to cool simple electronic applications across a multitude of markets. Without the modern day heat sink, electronics that we have become familiar with throughout our everyday lives will cease to exist. I will design these heat sinks using Solid Works 3D CAD. I will then test the heat sinks using ICEPAK CFD software, where I will model the heat sink against a 5 watt application, inside of a cabinet that models the chassis of a computer. After receiving these results, …

Manufacturing Processes In An All-Aluminum Airframe, Stewart Mcdougall

Aerospace Engineering

One often overlooked aspect to building an aircraft is the manufacturing process used to put it into production. This may be a major contributor to acquisition cost and requires a large amount of money to implement. Once all the tooling has been purchased, one of the greatest costs is labor. The experience of building an all-aluminum aircraft shows that the production process is one which may be done in many different ways. Minimizing the assembly time is important for aircraft manufacturers and one of the best ways to do that is on the assembly line itself. Specific practices in the …

Flaperon Assembly Manual For Pegastol Aftermarket Wings, Eric Alan Gray

Aerospace Engineering

No abstract provided.

Feasibility Analysis For Electrically-Powered Hoverboard, Cameron Chan, Jason Cortez, Jay Lopez

Aerospace Engineering

Composite materials are engineered by combining two or more constituent materials with significantly different physical or chemical properties in such a way that the constituents are still distinguishable, and not fully blended. Due to today’s high rising prices of gasoline and aviation fuel costs, many manufacturers have turned to the use of lightweight composites in their designs due to the advantages of the composite material, which include outstanding strength, excellent durability, high heat resistance, and significant weight reduction that the composite material properties hold. The purpose of this project is to design and construct a composite structure for an electrically-powered …

Ergonomic Lifter, Bejan Brian Banihashemi, Dylan James Schockemoehl, Andrew Ouellet

Mechanical Engineering

No abstract provided.

Emergency Response Manufacturing: Lead Time Minimization And Human Factors For Ozone Water Filter Assembly And Kitting Process, Travis Gary

Industrial and Manufacturing Engineering

In the unfortunate event of a natural disaster affecting San Luis Obispo, response from national entities cannot be relied upon for a timely or efficient response. Local disaster recovery is superior because it minimizes response time, the need for costly stockpiling and creates a solution that is uniquely suited to the community that empowers local people in their most troubled times. Extensive planning is required for local disaster recovery and this project aims to provide the research and recovery system design required to implement an effective recovery plan.

Potable water is the primary need for people in the disaster situations …

The Fresh Express Lean Changeover Project, Mario Borbas

Industrial Technology and Packaging

In the current economic turmoil, industry leaders across the globe are resorting to means of increasing efficiency without having a large initial investment. Lean manufacturing principles have been adopted by companies because of its ability to increase throughput, lower overhead, reduce waste, and increase the overall quality of products. The value of lean manufacturing solutions has been increasing in the past decade and continues to increase into 2011.

This project is centered on a current situation regarding a changeover process that has recently been made more efficient. The goal is to create new ways to make this same process even …

Adapted Recumbent Bike, Kurtis Mundell, Dane Tiemeier, Laura Yakuma, Darius Yu

Mechanical Engineering

The adapted recumbent project was to redesign a disabled veteran’s recumbent bicycle. The main areas of concern were the crank pedal, chain tension, braking and steering system, and ergonomics. Since the customer is an avid biker, this bike will be used often, so the design is based on the ease of repair and replacement. The crank system was redesigned to a lightweight, adjustable part with chain clearance and high strength. The chain tension was improved by replacing the existing single idler wheel/chain tube system with a dual idler wheel system. The dual idler has a titanium sprocket in one of …

Design Of A Low Cost Powered R/C Combat Airplane And Manufacturing Plan, Jonathan N. Bailey

Industrial and Manufacturing Engineering

The goals of this project are to design a low cost powered remote control combat airplane capable of outdoor flight, named the Aero EX and to develop a manufacturing plan to produce each unit at a selling price of $200, while operating at a 25 vehicle batch rate inside a 1,000 square foot facility. These goals are achieved using: Aerospace fundamentals to design the vehicle, Design for Manufacturability to optimize the design for minimal use of labor, Design for Assembly to give consumers the ability to build the vehicle without fixtures, Pull production to eliminate scheduling and match customer demand. …

Design For Manufacturing Of Sports Equipment, Cedrick Bit, Christopher L. Head

Industrial and Manufacturing Engineering

The purpose of this project was to validate industrial designs for a product in its conceptual stage and suggest/implement design changes that suit the contracting company’s needs while assuring the product maintains its basic functional requirements. Techniques and methods used to validate the design include 3‐D solid modeling, physical product application using rapid prototyping to produce the product. Methods of design for manufacturing were analyzed in the design. Processes used in the validation and verification of the design include solid modeling design, methods of measurements, fixture design and manufacturing processes. Full design specifications and solid model files were finalized and …

Lean Erp Systems: Existence And Viability In Today's Manufacturing Industry, Miroslav Djuric

Master's Theses

This thesis evaluates the existence and viability of lean ERP systems in today’s manufacturing industry. Results from the research show that current practitioners of lean – who also utilize ERP systems – do not have a strong enough link between the two to consider their ERP systems, and overall organizations, as being truly lean.

Few articles and research papers in today’s body of knowledge contain information on the concept of lean ERP. A survey, sent to numerous industry professionals and posted on lean manufacturing websites, provided the results necessary for statistical analysis. The conclusions obtained from this survey analysis provided …