Open Access. Powered by Scholars. Published by Universities.®
- Institution
Articles 1 - 5 of 5
Full-Text Articles in Engineering
Biomass Characterization And Insulation Optimization Studies, Hussein Awad Kurdi Saad
Biomass Characterization And Insulation Optimization Studies, Hussein Awad Kurdi Saad
Doctoral Dissertations and Master's Theses
This study indicates how biomass materials can be effectively used as naturally sustainable alternatives to insulation materials. Barley grains and oak leaves, straw, and jute are collected, and crushed into powders/ chopped pieces. The physical characteristics are measured to characterize each powder. The biomass powder reinforced composites are manufactured in varying weight ratios. The density and thermal conductivity of composite materials are measured. The properties of composites compared to those of commercial insulation materials are found to be close to them. Furthermore, genetic algorithms (GA) can be used to achieve multi-objective optimization entailing maximizing insulation (minimizing heat transfer) and simultaneously …
Flow And Thermal Transport In Additively Manufactured Metal Lattices Based On Novel Unit-Cell Topologies, Inderjot Kaur
Flow And Thermal Transport In Additively Manufactured Metal Lattices Based On Novel Unit-Cell Topologies, Inderjot Kaur
Theses and Dissertations
The emergence of metal Additive Manufacturing (AM) over the last two decades has opened venues to mitigate the challenges associated with stochastic open-cell metal foams manufactured through the traditional foaming process. Regular lattices with user-defined unit cell topologies have been reported to exhibit better mechanical properties in comparison to metal foams which extend their applicability to multifunctional heat exchangers subjected to both thermal and mechanical loads. The current study aims at investigating the thermal-hydraulic characteristics of promising novel unit cell topologies realizable through AM technologies. Experimental investigation was conducted on four different topologies, viz (a) Octet, (b) Face-diagonal (FD) cube, …
Development And Applications Of A Sensor For Measurement Of Different Modes Of Heat Transfer On Foods In A Residential Oven., Kervins Petit-Bois
Development And Applications Of A Sensor For Measurement Of Different Modes Of Heat Transfer On Foods In A Residential Oven., Kervins Petit-Bois
Electronic Theses and Dissertations
Thermal characterization of an oven is an important part of designing an oven. Understanding how changes in cooking algorithm, oven construction, and oven materials affect cooking performance is critical in ensuring that an oven is properly designed. Often temperature data is used to characterize oven behavior, but this neglects the mode of heat transfer used to achieve these temperatures. Several studies have compared the different modes of heat transfer and cooking performance and have shown that cooking performance in radiation dominated modes are different than in convection dominated modes. The goal of this study is to develop a heat flux …
Mmteg Heatsink Design, Peyton Nienaber, Kadin Feldis, Alec Savoye, Jack Waeschle
Mmteg Heatsink Design, Peyton Nienaber, Kadin Feldis, Alec Savoye, Jack Waeschle
Mechanical Engineering
In this document, Cal Poly Senior Design Team F16 presents a summary of its work developing a suitable heatsink for Gas Technology Institute’s Methane Mitigation Thermoelectric Generator. After several months of iterating between experimental testing and simulated heat transfer, a suitable prototype was selected for use in further refining simulation parameters. This was called the structural prototype and it allowed Team F16 to confirm several remaining unknowns relating to component thermal conductivity. All documentation of this process can be found in Preliminary, Critical, and Interim Design Review documents (PDR, CDR, IDR), included in this report. Having a realistic model …
Cooling Systems Analysis For Plastic Mold Injection Tools, Veronica Flores Quijada
Cooling Systems Analysis For Plastic Mold Injection Tools, Veronica Flores Quijada
Electronic Thesis and Dissertation Repository
The Plastic Injection Mold (PIM) industry has been searching for new technologies that improve the manufacturing of parts by reducing the production time and cost as well as increasing the quality of the product. The cooling systems in the PIM are designed initially to be straight-drilled into the mold, but this manufacturing process has traditionally not been very effective, since for molded parts with complex geometries, the cooling channels are not able to reach certain areas. This limitation has led the industry to develop conformal cooling channels that use the additive manufacturing technology, which allows the cooling channels to conform …