Engineering Commons^™

Measurement Of Conduction, Radiation, And Convection Thermal Energy To Assess Baking Performance In Residential Ovens., Sean Simpson

Electronic Theses and Dissertations

Residential ovens are complicated thermal environments capable of delivering convection, conduction, and radiation heat transfer to food. The amount and mode of heat transfer can change based on the design of the oven cavity, cooling systems, and oven cycle algorithms. Studies have shown that the changes in one heat transfer mode can have an impact on the quality of baked goods. The many variables involved make designing residential ovens a time consuming and costly process. The goal of this study is to adapt thermal energy sensing technology to collect energy data from a residential oven and develop correlations to quality …

Thermal Boundary Condition Effects On Local Supercritical Co2 Heat Transfer Trends In Tubes, Nicholas C. Lopes

Doctoral Dissertations and Master's Theses

Supercritical carbon dioxide (sCO2) is a promising heat transfer fluid for the refrigeration and power generation industries due to its unique thermal properties and low environmental impact. To understand it as an alternative to traditional working fluids, the thermophysical and heat transfer phenomena of sCO2 are often studied using simplified geometries (tubes). Focus has been placed on investigating averaged heat transfer trends under an array of flow conditions with either a constant wall heat flux, constant wall temperature, or conjugate thermal boundary condition. Less emphasis has been placed on studying local sCO2 heat transfer developments. Tubular sCO2 numerical models that …

Biomass Characterization And Insulation Optimization Studies, Hussein Awad Kurdi Saad

Doctoral Dissertations and Master's Theses

This study indicates how biomass materials can be effectively used as naturally sustainable alternatives to insulation materials. Barley grains and oak leaves, straw, and jute are collected, and crushed into powders/ chopped pieces. The physical characteristics are measured to characterize each powder. The biomass powder reinforced composites are manufactured in varying weight ratios. The density and thermal conductivity of composite materials are measured. The properties of composites compared to those of commercial insulation materials are found to be close to them. Furthermore, genetic algorithms (GA) can be used to achieve multi-objective optimization entailing maximizing insulation (minimizing heat transfer) and simultaneously …

Flow And Thermal Transport In Additively Manufactured Metal Lattices Based On Novel Unit-Cell Topologies, Inderjot Kaur

Theses and Dissertations

The emergence of metal Additive Manufacturing (AM) over the last two decades has opened venues to mitigate the challenges associated with stochastic open-cell metal foams manufactured through the traditional foaming process. Regular lattices with user-defined unit cell topologies have been reported to exhibit better mechanical properties in comparison to metal foams which extend their applicability to multifunctional heat exchangers subjected to both thermal and mechanical loads. The current study aims at investigating the thermal-hydraulic characteristics of promising novel unit cell topologies realizable through AM technologies. Experimental investigation was conducted on four different topologies, viz (a) Octet, (b) Face-diagonal (FD) cube, …

Development And Applications Of A Sensor For Measurement Of Different Modes Of Heat Transfer On Foods In A Residential Oven., Kervins Petit-Bois

Electronic Theses and Dissertations

Thermal characterization of an oven is an important part of designing an oven. Understanding how changes in cooking algorithm, oven construction, and oven materials affect cooking performance is critical in ensuring that an oven is properly designed. Often temperature data is used to characterize oven behavior, but this neglects the mode of heat transfer used to achieve these temperatures. Several studies have compared the different modes of heat transfer and cooking performance and have shown that cooking performance in radiation dominated modes are different than in convection dominated modes. The goal of this study is to develop a heat flux …

Mmteg Heatsink Design, Peyton Nienaber, Kadin Feldis, Alec Savoye, Jack Waeschle

Mechanical Engineering

In this document, Cal Poly Senior Design Team F16 presents a summary of its work developing a suitable heatsink for Gas Technology Institute’s Methane Mitigation Thermoelectric Generator. After several months of iterating between experimental testing and simulated heat transfer, a suitable prototype was selected for use in further refining simulation parameters. This was called the structural prototype and it allowed Team F16 to confirm several remaining unknowns relating to component thermal conductivity. All documentation of this process can be found in Preliminary, Critical, and Interim Design Review documents (PDR, CDR, IDR), included in this report. Having a realistic model …

Cooling Systems Analysis For Plastic Mold Injection Tools, Veronica Flores Quijada

Electronic Thesis and Dissertation Repository

The Plastic Injection Mold (PIM) industry has been searching for new technologies that improve the manufacturing of parts by reducing the production time and cost as well as increasing the quality of the product. The cooling systems in the PIM are designed initially to be straight-drilled into the mold, but this manufacturing process has traditionally not been very effective, since for molded parts with complex geometries, the cooling channels are not able to reach certain areas. This limitation has led the industry to develop conformal cooling channels that use the additive manufacturing technology, which allows the cooling channels to conform …

Relationship Between Thermal Conductivity And Free Electrons In Metal, Yansong Liu

Senior Theses

An experiment was designed and conducted to explore the relationship between thermal conductivity with free electrons in metal. In the experiment, copper, iron, aluminum, and titanium rods with close diameters were used to carry out the experiment. Each rod was heated up by a heat unit at one end while cooled on the other end with a heat sink to maintain a steady state. DC current was applied to rods in the direction along, as well as against, the heat flow. Thermal conductivities were measured in these two situations for each rod. Results showed electrons do dominate thermal flow inside …

Heat Transfer Modeling And Optimization Of A Carbonized Microvascular Solar Receiver, Taylor Brown

Boise State University Theses and Dissertations

Concentrating solar power is an emerging renewable energy source. The technology can collect and store thermal energy from the sun over long durations, generating electricity as needed at a later time. Current CSP systems are limited to a maximum operational temperature due to constraints of the working fluid, which limits the maximum possible efficiency of the system. One proposed pathway forward is to utilize a gas phase for the working fluid in the system such as supercritical carbon dioxide.

A composite gas phase modular receiver is being developed by researchers at Boise State University and the University of Tulsa. The …

Experimental Evaluation Of Heat Leak And Convective Heat Transfer In A Household Freezer., Catherine E. Berghuis

Electronic Theses and Dissertations

Heat leak into household refrigerated cabinets is a key driver affecting energy consumption and efficiency of the cooling system. Additionally, knowledge of heat transfer coefficients of internal surfaces is valuable in the development of cabinet and system level performance simulations. Several studies have examined heat leak of refrigeration units using heat flux sensors (HFS); however, no such studies have used heat flux measurements to derive convective heat transfer coefficients of the refrigerated unit walls. The goal of this study is to evaluate the use of HFS to quantify heat leak into a 490-liter freezer and determine the wall convective heat …

Assessment And Improvement Of Computational Fluid Dynamics Methods For Separated Turbulent Flows At Low Reynolds Numbers, Tom Mancuso

Dissertations, Master's Theses and Master's Reports

This study investigates the accuracy of Computational Fluid Dynamics (CFD) models to predict heat transfer in turbulent separated flows at low Reynolds numbers. A novel improvement of a Scale Adaptive technique is also presented. A spectrum of turbulence models is used to simulate flow and heat transfer of two geometries; fully developed flow through a staggered tube bank and a square prism in cross flow. Experimental data for both local heat transfer and velocity data are available in the literature for these cases and have been used extensively evaluate various CFD methods. Six unsteady models were used and the results …

Critical Radius Of Insulation, Maria N. Ambrose, Samuel J. Sayre, Travis W. Martin, Matt T. Sterling

Mechanical Engineering

The critical radius of insulation is a counterintuitive concept within the study of heat transfer. The theory states that adding insulation to a cylindrical or spherical object will increase the rate of heat loss rather than decrease it, if the radius (thickness) of the insulation is at its “critical” value. The Critical Radius of Insulation Senior Project is designed to demonstrate this phenomenon to Heat Transfer students via a portable apparatus. The concept will be demonstrated with a cylindrical object which is heated by way of a separate voltage source. Thermocouples will display the temperature of the cylinder while insulation …

Ignition And Extinction Behavior Of Fuels In A Microcombustor, Pawan Sharma

LSU Doctoral Dissertations

Conventional fuel testing device-CFR engine requires large quantities of fuels, which makes it unsuitable for research of small samples of fuels. This current study seeks to address this limitation by using an externally heated microcombustor as an alternative fuel testing device. Mainly three combustion behaviors have been observed inside a microcombustor: strong flames at higher flow rates, Flames with Repetitive Extinction and Ignition (FREI) at intermediate flow rates, and weak flames at marginal flow rates. In previous studies, weak combustion behavior has been proven suitable to study fuel properties from small samples of fuels. Microcombustor experiments typically rely on flame …

Optimization Of The Practice Of Slow Cooling Steel Bars: A Redesign And Modernization Of Materials, Eryn Johnston

Mechanical Engineering Undergraduate Honors Theses

Throughout the process of steel making, certain grades of steel are a higher risk for defects caused by the inability to quickly diffuse hydrogen through the steel when cooled to room temperature at a normal rate based on the ambient air temperature. To reduce the hydrogen flaking defects that are caused due to hydrogen entrapment in the steel, the process of slow cooling is utilized. This process reduces the cooling rate of steel bars by keeping them at a higher temperature for extended periods and in turn gives the hydrogen a chance to fully dissipate from the steel. In many …

Liquid-To-Liquid Low Grade Waste Heat Recovery Using A Two-Channel Loop, Waleed Farwana

Masters Theses

The use of thermoelectric generators (TEGs) for producing electric energy from low grade “waste heat” has been theorized to provide a sustainable and low-cost energy source for electric power plants. The purpose of this study is to model and experimentally validate a TEG device that takes advantage of low grade waste heat (approximately 100-150 degrees Celsius) in liquid form in order to generate power that can be used for various applications in the surrounding environment. This research aims to demonstrate that optimized TEG designs bear the potential to compete with other methods of low grade waste heat energy harvesting in …

Selecting The Most Effective Energy Modeling Tool Based On A Project Requirement, Sodiq Akande

Electronic Theses and Dissertations

Building energy usage can be derived and controlled by performing building energy modeling. BEM can be performed using numerous software tools such as DesignBuilder, OpenStudio, EnergyPlus etc. These modeling tools can be sorted into three different modeling categories: Black-box, Gray-box and White-box. It is important for a modeler to be able to quickly select the proper tool from the proper category to meet the need of the project. To validate the method of categorizing tools, the three models generated using tools from each category and the modeling outputs required were compared. Each model was designed to estimate the amount of …

Heat Flow Characterization Of Speakers, Sabrina M. Gough, Lydia K. Hedge, Nicolas M. Jones

Mechanical Engineering

Statement of Confidentiality: The complete senior project report was submitted to the project advisor and sponsor. The results of this project are of a confidential nature and will not be published at this time.

Optimization Of Heat Sinks In A Range Of Configurations., Archibald Allswell Amoako

Electronic Theses and Dissertations

In this study, different heatsink geometries used for electronic cooling are studied and compared to each other to determine the most efficient. The goal is to optimize heat transfer of the heat sinks studied in a range of configuration based on fin geometry. Heat sinks are thermal conductive material devices designed to absorb and disperse heat from high-temperature objects (e.g. Computer CPU). Common materials used in the manufacturing of heat sinks are aluminum and copper due to their relatively high thermal conductivity and lightweight [1]. Aluminum is used as the material for the heatsinks studied in this research project. To …

The Development And Numerical Modelling Of A Representative Elemental Volume For Packed Sand, Ashraf Thabet

Electronic Thesis and Dissertation Repository

The motivation of this thesis is the development of simple microscopic-scale model (representative elemental volume; REV) that can be used to conduct flow and heat transfer simulations from which closure coefficients can be established for the volume-averaged transport equations for porous media (packed bed). The thesis provides a brief introduction to the computational technique adopted for the geometric generation of the REV (YADE), followed by a parametric study undertaken to reveal the minimum number of particles inside the REV that are required to mimic the appropriate physics. Additional analysis was conducted with the goal of determining the influence of deviation …

Fluid Analysis In Solar Heat Pipes, Ben Krumholz, Michael Agavo, William Dundon

Mechanical Engineering

Evacuated tube solar collectors are efficient systems that use heat pipes to facilitate heat transfer. They use incoming solar radiation to heat water. Professor Mason Medizade tasked the team with choosing a component of the system to research and test its influence on system performance. The team investigated the working fluid that runs through the heat pipes. Distilled water, acetone, and ethanol at a range of fill volumes form 1 mL to 11 mL were tested. The team's goal was to find a volume for each fluid to maximize performance of the system. Performance was defined as average temperature rise …

A Model For Complex Heat And Mass Transport Involving Porous Media With Related Applications, Furqan A. Khan

Electronic Thesis and Dissertation Repository

Heat and mass transfer involving porous media is prevalent in, for example, air-conditioning, drying, food storage, and chemical processing. Such applications require non-equilibrium heat and mass (or moisture) transfer modeling inside porous media in conjugate fluid/porous/solid framework. Moreover, modeling of turbulence and turbulent heat and mass transfer becomes essential for many applications. A comprehensive literature review shows a scarcity of models having such capabilities. In this respect, the objectives of the present thesis are to: i) develop a formulation that simulates non-equilibrium heat and mass transfer in conjugate fluid/porous/solid framework, ii) demonstrate the capabilities of the developed formulation by simulating …

Wind And Thermal Effects On Ground Mounted Photovoltaic (Pv) Panels, Chowdhury Mohammad Jubayer

Electronic Thesis and Dissertation Repository

A combination of Computational Fluid Dynamics (CFD) simulations and wind tunnel experiments are carried out to investigate the effects of wind on the aerodynamic loading and heat transfer of a ground mounted stand-alone photovoltaic (PV) panel with tilt angle of 25^o in open country atmospheric boundary layer. Several azimuthal wind directions are considered: Southern 0^o, Southwest 45^o, Northwest 135^o and Northern 180^o. Three dimensional Reynolds-Averaged Navier-Stokes (RANS) approaches with an unsteady solver using Shear Stress Transport (SST) k-ω turbulence closure are employed for the CFD simulations, whereas Particle Image Velocimetry (PIV) and …

Single-Phase Turbulent Enthalpy Transport, Bradley J. Shields

Masters Theses

Vapor generation is central to the flow dynamics within fuel injector nozzles. Because the degree of atomization affects engine emissions and spray characteristics, quantification of phase change within diesel fuel injectors is a topic of design interest. Within the nozzle, the large pressure gradient between the upstream and downstream plena induce large velocities, creating separation and further pressure drop at the inlet corner. When local pressure in the throat drops below the fluid vapor pressure, phase change can occur with sufficient time. At the elevated temperatures present in diesel engines, this process can be dependent upon the degree of superheat, …

Formula Sae Cooling System Design, Lisa Van Den Berg, Brandon Lofaro

Mechanical Engineering

The overall objective of this senior project is to develop, via testing and analysis, a guided process that will aid the Cal Poly Formula SAE team in designing their cooling system. More specifically, a set of designed tests will yield the results necessary in determining a combination of fan and radiator that will achieve appropriate cooling.

A test section that has the capability of interfacing with both the wind tunnel in the Thermal Science Lab and a radiator will be used to facilitate the necessary experiments. The wind tunnel is powered by fan controlled by a variable frequency drive that …

Computational Analysis To Enhance Laminar Flow Convective Heat Transfer Rate In An Enclosure Using Aerosol Nanofluids, Andrew Hudson

Electronic Theses and Dissertations

The current research intends to provide a starting point to effectively model aerosol heat transfer in a narrow, enclosed body. This research can lead to future modeling of nano fluids including their heat transfer characteristics and erosion effects on the walls of an enclosure. The model was developed using ICEM CFD for the mesh and FLUENT for the fluid flow modeling. Six different aspect ratio enclosures were developed to study the effects of varying aspect ratio. The natural convection of air was developed first to establish the appropriateness of the models being used. A mesh check was performed using one …

Design And Simulation Of Passive Thermal Management System For Lithium-Ion Battery Packs On An Unmanned Ground Vehicle, Kevin Kenneth Parsons

Master's Theses

The transient thermal response of a 15-cell, 48 volt, lithium-ion battery pack for an unmanned ground vehicle was simulated with ANSYS Fluent. Heat generation rates and specific heat capacity of a single cell were experimentally measured and used as input to the thermal model. A heat generation load was applied to each battery and natural convection film boundary conditions were applied to the exterior of the enclosure. The buoyancy-driven natural convection inside the enclosure was modeled along with the radiation heat transfer between internal components. The maximum temperature of the batteries reached 65.6 °C after 630 seconds of usage …

Silicon Wafer Temperature Distribution, Daniel Gonzalez, Nathan Jones, Dylan Justice

Mechanical Engineering

Applied Materials is a global company that designs equipment for use in the semiconductor manufacturing industry. The scope of this project covers process chambers used for depositing thin chemical films onto silicon wafers. These processes must take place in particularly specific environments– including extremely low pressures and high temperatures. One challenge engineers face when designing these processes is carefully controlling the thermal behavior of silicon wafers. Typically, behavior is predicted using time consuming and computationally expensive CFD simulations. We have been asked to address this issue with a simpler, faster model which will allow engineers to reduce the total number …

An Investigation Of Mist/Air Film Cooling With Application To Gas Turbine Airfoils, Lei Zhao

University of New Orleans Theses and Dissertations

Film cooling is a cooling technique widely used in high-performance gas turbines

to protect turbine airfoils from being damaged by hot flue gases. Film injection holes are

placed in the body of the airfoil to allow coolant to pass from the internal cavity to the

external surface. The ejection of coolant gas results in a layer or “film” of coolant gas

flowing along the external surface of the airfoil.

In this study, a new cooling scheme, mist/air film cooling is proposed and

investigated through experiments. Small amount of tiny water droplets with an average

diameter about 7 μm (mist) is …

The Next Generation Router System Cooling Design, Garrett A. Glover

Master's Theses

Advancements in the networking and routing industry have created higher power electronic systems which dissipate large amounts of heat while cooling technology for these electronic systems has remained relatively unchanged. This report illustrates the development and testing of a hybrid liquid-air cooling system prototype implemented on Cisco’s 7609s router. Water was the working fluid through cold plates removing heat from line card components. The water was cooled by a compact liquid-air heat exchanger and circulated by two pumps. The testing results show that junction temperatures were maintained well below the 105°C limit for ambient conditions around 30°C at sea level. …

The Impact Of Heat Release In Turbine Film Cooling, Dave S. Evans

Theses and Dissertations

The Ultra Compact Combustor is a design that integrates a turbine vane into the combustor flow path. Because of the high fuel-to-air ratio and short combustor flow path, a significant potential exists for unburned fuel to enter the turbine. Using contemporary turbine cooling vane designs, the injection of oxygen-rich turbine cooling air into a combustor flow containing unburned fuel could result in heat release in the turbine and a large decrease in cooling effectiveness. The current study explores the interaction of cooling flow from typical cooling holes with the exhaust of a fuel-rich well-stirred-reactor operating at high temperatures over a …