Engineering Commons^™

Water Vapor Movement In Freezing Aggregate Base Materials, Maile Anne Rogers

Theses and Dissertations

The objectives of this research were to 1) measure the extent to which water vapor movement results in water accumulation in freezing base materials; 2) evaluate the effect of soil stabilization on water vapor movement in freezing base materials; 3) determine if the corresponding changes in water content are sufficient to cause frost heave during winter; 4) determine if the corresponding changes in water content are sufficient to cause reductions in stiffness during spring; 5) evaluate relationships between selected material properties, freezing conditions, and the occurrence and impact of water vapor movement; and 6) numerically simulate heat and water movement …

Frost Susceptibility Of Base Materials Treated With Asphalt Emulsion, Noelle Anderson

Theses and Dissertations

The objective of this research was to investigate emulsion-treated base (ETB) frost susceptibility in terms of both freeze-thaw cycling and frost heave. The research performed in this study involved laboratory testing of ETB materials sampled from both the Redwood Road and 7800 South reconstruction projects in northern Utah. The effects of freeze-thaw cycling were evaluated by comparing the stiffness and strength of tested specimens to the same properties of control specimens not subjected to freeze-thaw cycling. Frost heave testing enabled evaluation of the effects of emulsion content and degree of curing on the volumetric stability of ETB materials during sustained …

Developing Guidelines For Including Mobility-Based Performance Specifications In Highway Construction Contracts, Shawn J. Larson

Theses and Dissertations

Construction zones can greatly affect the traffic flow on roadways, especially when lane closures are required. Traditionally, the Utah Department of Transportation (UDOT) has used traffic management specifications that only allow lane closures and road work to be done during predetermined hours or specifications that require a certain number of lanes to be open at all times. Recently, mobility-based work-zone traffic flow maintenance has been considered. This method requires continuous monitoring of mobility-based performance data and a mechanism to send alerts to the contractors when the mobility data does not meet the standards set by the specifications. UDOT recently tested …

Condition Assessment Of Decommissioned Bridge Decks Treated With Waterproofing Membranes And Asphalt Overlays, Eric Scott Sumsion

Theses and Dissertations

The objective of this research was to assess the condition of four decommissioned bridge decks treated with waterproofing membranes and asphalt overlays following the completion of their service lives. Large samples were cut from each of the bridge decks immediately prior to demolition and taken to the Brigham Young University Highway Materials Laboratory, where extensive sampling and testing was performed. Methods used to evaluate the condition of the bridge deck samples included visual inspection, hammer sounding, Schmidt rebound hammer testing, resistivity testing, half-cell potential testing, linear polarization testing, cover depth measurement, and chloride concentration measurement. The samples were removed from …

The Performance Of Risk Management And Innovation In Construction Manager/General Contractor Delivery In Civil Construction Applications, Rebecca M. Owens

Theses and Dissertations

Project teams that deliver high risk, complex projects in the civil construction industry need tools to enable successful delivery. Construction Manager/General Contractor (CM/GC) is an innovative alternate delivery method, providing one such a tool. CM/GC furnishes public agencies with an attractive option for delivering projects in a less adversarial and more constructive manner by involving the contractor during design. The sophisticated public owner does not have to relinquish control of the details of the design in order to accelerate the schedule or see the benefits of real-time cost estimating data. There are also significant cost and schedule benefits with not …

Introducing The Vuepod: Development And Testing Of A Low-Cost Large-Scale Stereoscopic Immersive System Using 3d Lcd Televisions, Shane Makana Hayden

Theses and Dissertations

3D immersive visualization systems, or CAVEs™, have found wide adoption for use in geosciences, planetary science, medical research, and computer science. However, much of the potential for such systems in practical civil and environmental engineering settings has been severely limited due to 1) extreme costs in both hardware and software; 2) immobility due to calibration and darkroom requirements; and 3) extensive and expensive manpower requirements for both operation and maintenance. This thesis presents the development and testing of a new mobile low-cost immersive stereo visualization system -- the "VuePod" -- that attempts to address these challenges through the use of …

Structural Analysis And Optimization Of Skyscrapers Connected With Skybridges And Atria, Amy Jean Taylor Mccall

Theses and Dissertations

Skybridges and atria between buildings are becoming more and more popular. Most current skybridge connections are either roller or rigid-connections. This dissertation presents an investigation of the structural analysis and optimization of skyscraper systems with hinge-connected skybridges, and compares the results to skyscraper systems with roller-connected skybridges and to skyscraper systems without skybridges altogether. Also presented is an investigation of the structural analysis and optimization of skyscrapers both with and without atria between the buildings. It was assumed that the atria envelope was constructed with cushions made from lightweight, transparent, and flexible Ethylene Tetrafluoroethylene (ETFE). A simplified skyscraper skybridge model …

Seasonal Change In Bacteria Levels And Eluent Comparison For The Enumeration Of E. Coli And Enterococci From Recreational Beach Sand, Kyle Hines

Theses and Dissertations

Research into the causes of bacterial contamination of recreational beaches has been increasing. Many researchers are now looking to enumerate bacteria from beach sands in order to find the connections between the water and sand quality. As the number of these studies increase, there is a need to determine a standard procedure for enumerating bacteria from sand. The eluent that a researcher chooses could impact the results that they obtain due to ionic strength. The first part of this paper compares the E. coli and Enterococci counts of identical sand samples using phosphate buffered saline and distilled water as eluents. …

Development Of Novel Bioelectrochemical Systems For In Situ Nitrate Removal From Groundwater, Yiran Tong

Theses and Dissertations

This study aims to develop new approaches for in situ nitrate removal from groundwater by using bioelectrochemical systems (BES). BESs employ bioelectricity generated from organic compounds to drive nitrate moving from groundwater into the electrode chamber and reduce nitrate to nitrogen gas by heterotrophic denitrification. In first phase experiments, nitrate ions were driven into the anode chamber of a de-coupled reactor, whose electrode chambers were separated, where heterotrophic denitrification took place with organic reduction. It was proved that by applying additional electrical potential at 0.8V, the reactor could achieve highest removal rate of 208.2±13.3 g NO3--N/m3/d, when initial nitrate concentration …

Mechanical Properties And High-Temperature Performance Of A Polyester Resin Modified Using Fgd Gypsum, Morteza Janbaz

Theses and Dissertations

High-temperature performance of polyester- based construction materials is an important consideration when fire safety is a concern. These materials are typically used as non-structural components of buildings and other structures. Structural retrofits using fiber-reinforced polymer (FRP) composites are also gaining popularity. However, a major disadvantage of polymer- based materials (including FRP composites) is their flammability and toxic gas generation at high temperatures. The main objective of this research effort was to determine the mechanical properties and high-temperature performance of a polyester resin modified with various amounts of an industrial by-product additive. The additive used was Flu-Gas Desulfurization (FGD) gypsum, which …

Recovering Bioresources From Integrated Photo-Bioelectrochemical System, Li Xiao

Theses and Dissertations

Compared to traditional wastewater treatment technologies, the electricity generation is one of the most important advantages of bioelectrochemical systems (BES). However, due to its high cost and low energy production, BES technologies are still far away from feasible application. The main purpose of this work was to investigate ways to improve the electricity generation and reduce the cost of BES technologies. We focused on microbial fuel cells (MFCs) and microbial electrolysis cells (MECs) as two representative BES technologies. In order to improve the energy performance of MFCs, an accurate evaluation of the energy is necessary. However, the common evaluation methods …

Investigation Of Application Niche For Sustainable Wastewater Treatment Using Microbial Fuel Cells, Patrick Thomas Kelly

Theses and Dissertations

Microbial fuel cells represent a sustainable wastewater treatment technology due to its simultaneous treatment of contaminants and electricity production. Selection of suitable substrates is important to identifying proper application of microbial fuel cell (MFC) technology. In this work, four identical MFCs were used to treat the wastes sampled from different stages of a cheese wastewater treatment process, and both treatment performance and energy balance were examined. The two MFCs treating liquid wastes achieved more than 80% removal of total chemical oxygen demand (TCOD), while the other two MFCs fed with sludge or cheese whey removed about 60% of TCOD. The …

Sediment Microbial Fuel Cell As Sustainable Power Resource, Ananta Kothapalli

Theses and Dissertations

This research demonstrates that Ceratophyllum demersum a root less non vascular aquatic plant has negatively affected the power generation from a Sediment Microbial Fuel cell (SMFC). In SMFC the reduced organic matter in the sediment in water produces electrons, which reduces oxygen. Whereas in Plant SMFC continuous supply of organic matter to the anode is done by rhizodeposition (root exudates). Six SMFCs were run for more than 3 months to see the effect of plants, pH and temperature on power generation. Out of six only two SMFC showed stable data. The maximum power density 18 ± 1mW/m3 was generated from …

The Effectiveness Of Silane And Siloxane Treatments On The Superhydrophobicity And Icephobicity Of Concrete Surfaces, Sunil M. Rao

Theses and Dissertations

Icy roads lead to treacherous driving conditions in regions of the U.S., leading to over 450 fatalities per year. De-icing chemicals, such as road salt, leave much to be desired. In this report, commercially available silane, siloxane, and related materials were evaluated as solutions, simple emulsions, and complex emulsions with incorporated particulates, for their effectiveness as superhydrophobic treatments. Through the development and use of a basic impact test, the ease of ice removal (icephobicity) was examined as an application of the targeted superhydrophobicity.

A general correlation was found between icephobicity and hydrophobicity, with the amount of ice removed on impact …

Second-Order Perturbation Analysis Of The St. Venant Equations In Relation To Bed-Load Transport And Equilibrium Scour Hole Development, Frans Joseph Lambrechtsen

Theses and Dissertations

This analysis is an expansion of research done by Rollin Hotchkiss during his Ph.D work. The research uses fluid flow, sediment transport, and perturbation theory to predict where scour will occur in a variable-width channel. The resulting equations also determine equilibrium scour depth based upon the stream bed elevation derived from a dimensionless bed slope equation. Hotchkiss perturbed the width of the channel using a second order Taylor Series perturbation but neglected second order terms. The present work follows the same procedures as Hotchkiss but maintains the second order terms. The primary purpose is to examine how the additional terms …

Using Bioelectrochemical Systems For Sustainable Desalination, Bo Zhang

Theses and Dissertations

Desalination of seawater or brackish water holds the potential to solve the freshwater shortage that is threatening nearly half of the world population. Current desalination technologies are energy intensive, which makes the desalinated water prohibitively expensive. In this study, investigations have been made to use renewable energy sources from organic waste to power the desalination process. Since desalination is driven by renewable energy, such desalination systems are more sustainable than currently wide employed commercial technologies. Efforts have been made to study how to operate BES driven desalination process such that the energy consumption will be minimized. Forward osmosis technology is …

Deicer Usage On Concrete And Asphalt Pavements In Utah, Chase David Thomas

Theses and Dissertations

The objectives of this research were to 1) compile winter maintenance data for the Utah Department of Transportation (UDOT) to directly compare concrete and asphalt pavements with regards to deicer usage and 2) determine if there is a statistical difference in deicer usage on concrete and asphalt pavements. To this end, three data sources were consulted for this research: Material Maintenance Quality Assurance (MMQA) database, UDOT road database, and Google Maps. The final compiled data set prepared for analysis in this research contained deicer quantities by deicer type, pavement surface areas by pavement material type, traffic, longitude, latitude, and elevation …

Hot Spot Identification And Analysis Methodology, Jacob S. Farnsworth

Theses and Dissertations

The Utah Department of Transportation (UDOT) Traffic and Safety Division continues to advance the safety of roadway sections throughout the state. To aid UDOT in meeting their goal the Department of Civil and Environmental Engineering at Brigham Young University (BYU) has worked with the Statistics Department in developing analysis tools for safety. The most recent of these tools has been the development of a hierarchical Bayesian Poisson Mixture Model (PMM) statistical model of traffic crashes and safety on UDOT roadways statewide and the integration of the results of this model in a Geographic Information System (GIS) framework. This research focuses …

Aqueous Turbulence Structure Immediately Adjacent To The Air - Water Interface And Interfacial Gas Exchange, Binbin Wang

Theses and Dissertations

Air-sea interaction and the interfacial exchange of gas across the air-water interface are of great importance in coupled atmospheric-oceanic environmental systems. Aqueous turbulence structure immediately adjacent to the air-water interface is the combined result of wind, surface waves, currents and other environmental forces and plays a key role in energy budgets, gas fluxes and hence the global climate system. However, the quantification of turbulence structure sufficiently close to the air-water interface is extremely difficult. The physical relationship between interfacial gas exchange and near surface turbulence remains insufficiently investigated. This dissertation aims to measure turbulence in situ in a complex environmental …

Establishing And Understanding The Electron Balance In Microbial Fuel Cells, Fei Zhang

Theses and Dissertations

Microbial fuel cells (MFCs) have been intensively studied in the past decade as a promising alternative wastewater treatment technology. However, the critical mass balances such as carbon (or electrons) balances have not well addressed before. Clear understanding of a carbon balance in the anode of an MFC will help to identify electron distribution among different electron acceptors, and the limiting factors that divert electrons from electricity generation. In this study, the effect of substrate loading rate, sulfate, temperature, substrate type and nitrate concentration on MFC's performance were investigated. At different operation condition, the biomass, current, biogas, dissolved oxygen, sulfate and …

The Role Of Solution Chemistry And Cell Surface Properties In Mediating Bacterial Transport And Deposition In Porous Media And Interactioin With Nanomaterials, Lixia Wang

Theses and Dissertations

Groundwater is an important source for drinking water supply. Microbial contaminants have been implicated in two-third of the waterborne disease outbreak. Understanding the fundamental processes, the governing factors and the interfacial interactions that contribute to the deposition of microbial contaminants to porous media will help to elucidate the microbial attachment/transport profile and is highly needed for bioremediation in the environment as well as water purification industry.

In this study, the effects of (1) chemical factors including ionic strength, pH and concentration of phosphate, (2) biological factors including lipopolysaccharide (LPS), biofilm and biofilm extracellular polysaccharide (EPS), and strain type on E.coli …

Internal Curing Of Concrete Bridge Decks In Utah: Mountain View Corridor Project, Joseph Michael Yaede

Theses and Dissertations

The objectives of this research were to 1) monitor in-situ moisture and diffusivity for both conventional concrete and concrete containing pre-wetted lightweight fine aggregate (LWFA), 2) compare deck performance in terms of early-age cracking, compressive strength, and chloride ingress, and 3) compare concrete properties in terms of compressive strength, chloride permeability, elastic modulus, and water content in the laboratory using cylinders cast in the field at the time of deck construction. The research involved field and laboratory evaluations of four newly constructed bridge decks located in northern Utah, two constructed using conventional concrete and two constructed using pre-wetted LWFA to …

A Comparative Analysis Of Energy Modelingmethods For Commercial Buildings, Spencer Mark Salmon

Theses and Dissertations

This thesis researched the accuracy of measured energy data in comparison to estimated hand calculation data and estimated building energy performance simulation data. In the facility management industry, there is minimal evidence that building energy performance software is being used as a benchmark against measured energy usage within a building. Research was conducted to find examples of measured energy data compared to simulated data. The study examined the accuracy of a simulation software and hand calculations to measured energy data. Data suggests that comparisons may be made between building energy performance simulated data and measured data, though comparisons are solely …

Modeling And Optimization Of Space Use And Transportation For A 3d Walkable City, Bradley R. Mecham

Theses and Dissertations

This thesis presents an investigation of a new three-dimensional urban form where walking distances are less than a half-mile and congestion is minimal. The car-free urban form investigated herein is a city composed of skyscrapers massively interconnected with skybridges at multiple levels. The investigation consists of optimizing space use arrangement, skybridge presence or absence, and elevator number to simultaneously minimize total travel time, skybridge light blockage, and elevator energy usage in the city. These objectives are evaluated using three objective functions, the most significant of which involves a three-dimensional, pedestrian-only, three-step version of the traditional four-step planning model. Optimal and …

Large-Scale Testing Of Passive Force Behavior For Skewed Abutments With High Width-Height Ratios, Katie Noel Palmer

Theses and Dissertations

The effects of seismic forces and thermal expansion on bridge performance necessitate an accurate understanding of the relationship between passive force and backwall deflection. In past case studies, skewed bridges exhibited significantly more damage than non-skewed bridges. These findings prompted studies involving numerical modeling, lab-scale tests, and large-scale tests that each showed a dramatic reduction in passive force with increased skew. Using these results, a correlation was developed between peak passive force and backwall skew angle. The majority of these tests had length to height ratios of 2.0; however, for several abutments in the field, the length to height ratio …

An Analysis Of The Provo River Decree And Its Current Application To Provo Area Water Rights, Karsten Eugene Busby

Theses and Dissertations

Water scarcity in the west has created a long history of conflict. When Utah was settled, laws were instituted (both officially and otherwise) that allowed water users to use streams and springs in efficient ways without causing harm to other users. The Provo River Decree is a physical example of local water law that has been in place for almost a hundred years. While many changes have arisen in its area of jurisdiction, it is still drawn upon to determine water rights. Ambiguity, rigidity, and overall changes to use patterns have limited the application of the decree to present situations. …

Compositional And Structural Properties Of Emulsion-Treated Base Material: 7800 South In West Jordan, Utah, Lisa Renay Gurney

Theses and Dissertations

The objectives of this research were 1) to examine correlations between compositional and structural properties of emulsion-treated base (ETB) layers, determine which of these factors exhibit the greatest spatial variability, and determine if significant differences exist between different test sections on a given project and 2) to investigate temporal trends in the structural properties of base materials treated with asphalt emulsion and to assess the rate at which ETB design properties are achieved. The research conducted in this study focused on testing of the ETB layer constructed on 7800 South (SR-48) in West Jordan, Utah. The research conducted in this …

Evaluating The Effects Of Non-Anonymity On Student Team-Member Evaluations, Taylor Robert Smith

Theses and Dissertations

This thesis investigates the effect that non-anonymity has upon student team-member evaluations; more specifically, it looked at how to create conditions of openness and honesty in which students will readily give and receive constructive criticism. The central hypothesis of this research is that if students are taught and prepared to properly give and receive constructive criticism, and have multiple opportunities to do so, non-anonymous feedback is the most effective and desirable. In order to gauge the effects of non-anonymity, eight specific hypotheses relating to different aspects of the feedback process were tested. Predictions were made as to the effects upon …

Comparison Of Performance-Based Liquefaction Initiation Analyses Between Multiple Probabilistic Liquefaction Models Using The Standard Penetration Test, Alexander David Wright

Theses and Dissertations

For the most recent and correct article, please click here: http://ascelibrary.org/doi/abs/10.1061/9780784412787.086

This study examines the use of performance-based approaches in liquefaction hazard analysis. Two new methods of performance-based liquefaction initiation analysis are proposed which use the works of Juang et al. (2012) and Boulanger and Idriss (2012). Further advances are made by incorporating the performance-based magnitude scaling factors as proposed by Cetin et al. (2012). Using these new equations a comparative study is made between the three methods. Further comparisons are made between the performance-based approaches and the more widely used deterministic approaches. The comparisons reveal that on average for …

Accuracy Of A Simplified Analysis Model For Modern Skyscrapers, Jacob Scott Lee

Theses and Dissertations

A new simplified skyscraper analysis model (SSAM) was developed and implemented in a spreadsheet to be used for preliminary skyscraper design and teaching purposes. The SSAM predicts linear and nonlinear response to gravity, wind, and seismic loading of "modern" skyscrapers which involve a core, megacolumns, outrigger trusses, belt trusses, and diagonals. The SSAM may be classified as a discrete method that constructs a reduced system stiffness matrix involving selected degrees of freedom (DOF's). The steps in the SSAM consist of: 1) determination of megacolumn areas, 2) construction of stiffness matrix, 3) calculation of lateral forces and displacements, and 4) calculation …