Engineering Commons^™

Model Parameter Identification For Rod And Cone Oscillatory Potentials, Kehur Banker

Theses

The use of signal modeling of the oscillatory potential (OP) of the electroretinogram (ERG), in the study of cone-rod interaction is investigated. ERG response data were analyzed for red, orange, blue and white flashes on no background and with red flashes on a blue background (to suppress rod responses). The OP signals were extracted from the ERG by digital bandpass filtering and a signal model was fitted through a simplex algorithm to produce the parameters including "OP envelope-amplitude", latency in terms of "center-time" of the OP-envelope and OP frequency. Amplitude for red flashes with or without a blue background showed …

Low Pressure Chemical Vapor Deposition Of Copper Films From Cu(I)(Hfac)(Tmvs), Wei-Shang King

Theses

Recently, copper has been found as a possible substitute for Al alloys because of its low resistivity (1.67 μΩ • cm) and potentially improved resistance to electromigration. Conventional physical vapor deposition (PVD) method do not provide the conformal deposition profile for the high density integrated circuit, therefore, chemical vapor deposition (CVD) has become the most promising method for the resulting conformal profile.

In this work, a cold wall, single wafer, CVD tungsten reactor was used for the deposition of copper with Cu(I)(hfac)(tmvs). Film growth rates were between 100 to 800 A/min depending on processing conditions, and an Arrhenius type activation …

Investigation Of Velocity Distribution Within High Speed Waterjet, Hong Cao

Theses

The aim of this research was to investigate velocity distribution within the water jet at different conditions of jet formation. The water jet (WJ) velocity was measured by the use of Laser Transit Anemometer (LTA) and statistical technique which improved the accuracy of the velocity determination.

The velocities were measured for different diameters of the sapphire nozzle under different water pressures at different axial stand off distances and radial distances across the jet. The experiments performed in this study enabled us to evaluate the effects and conditions of the water jet on the velocity distribution. The acquired results provide information …

Synthesis Of Silicon Oxide/Vycor Composite Membrane Structures By An Optimized Lpcvd Process, Abhijit Datta

Theses

This study is focused on development of highly selective ceramic membrane structures consisting of silicon dioxide films synthesized by low pressure chemical vapor deposition (LPCVD) on mesoporous Vycor substrates. The ability of easily altering the composition of such films by varying the LPCVD processing parameters affords the opportunity of microengineering the pore structure by reducing the diameters of pre-existing pores in the support. The process parameters investigated include, deposition temperature, total pressure, and flow rate of oxygen. Both the kinetics and select properties of the deposits were examined. The growth rate as a function of temperature was seen to follow …

Viscoelastic Effects On Parallel Flow Stability, Transition To Turbulence, And Turbulent Flow, Michael Garofalo

Theses

The classical two dimensional theory of stability of parallel flow is extended to viscoelastic fluids. How the elasticity of the fluid affects the point of stability and determines the point of transition to turbulence is analyzed. In addition the magnification of disturbances is elucidated. This study is based on a viscoelastic constitutive equation which has been successful in predicting the experimental trends of various unsteady high shear rate laminar flows. A viscoelastic stability equation which is an extension to the Orr-Sommerfeld equation for a Newtonian fluid is derived and solved for a flow between parallel plates superimposed by a two-dimensional …

Area And Perimeter Measurements Of Cells With Bound Fluorescent Antibodies, Aicha Weiss

Theses

The objective of this research was to geometrically analyze the characteristics of cells, specifically area and perimeter. The images were transferred from HP A900 system to an AVS work station. The images were visualized and manipulated by the AVS which permits the distinction between the cell body, fluorescent object, and background. The intrinsic geometry of the cell was determined by using image processing algorithms written in C. The images were then passed through a threshold filter, thereby yielding a black background and a white cell body. The perimeter calculation was then applied to the black and white images. Two test …

Case Study Of Assembly Defects In Manufactured Products, Michael J. Withka

Theses

Design for Quality Manufacturability (DFQM) is a design tool that empowers engineers to create designs that are easily and effectively transformed into manufactured products. The goal of this methodology is to make designers aware of design characteristics that may lead to product defects during the assembly process. Acknowledging the possibility of these defects will enable the designer to institute design modifications early in the design phase. The benefits realized in this approach are a reduction in the number of defects in the finished product, reduced product cycle times, a reduction in monitoring costs and a reduction in time-to-market.

This thesis …

Preoperative Risk Assessment For Cardiac Surgery Using Piecewise Linear Regression Model, Arifa Zafar

Theses

In the present climate of quality assurance policies, rigorous requirements for informed consent, and a constantly changing patient population, a system of preoperative risk assignment for cardiovascular surgery was developed to monitor and evaluate surgical outcomes. The goal of this work is to estimate the preoperative risk associated with cardiac bypass surgery for patients in different risk categories. These risk categories are determined by the Parsonnet model which is based upon studying the severity of illness. The Parsonnet model assigns a risk value to a range of risk factors consisting of patient attributes and disease parameters. The aggregate of these …

An Investigation Into Artificial Intelligence Based Generative Computer Process Planning, William Tereshkovich

Theses

The process planning function can be further optimized with the introduction of an intelligent software package such as an Artificial Intelligence based Generative Computer Process Planning System. An AI based CAPP system, also categorized as an expert system, provides the vital link between design and manufacture, a "bridge" of knowledge in the information chain of manufacturing engineering. With the increasing role of computers in the process planning function, planning has become easier, faster, and more efficient.

This thesis provides an explanation of the process planning function and how artificial intelligence will improve it. Topics in AI techniques and procedures, knowledge …

Electrical Power Dispatch To Motors Using Digital Modulating Techniques, David Michael Canny

Theses

The trend towards digital and microprocessor based control of power electronic converters has increased the level of research into digital modulating techniques. This thesis examines the inherent digital nature of Binary Rate Modulation with particular attention concentrated on its suitability for dispatching power to three-phase loads. The circuit topology of a three-level inverter is also examined and its performance aspects are compared with those of the more conventional two-level inverter.

Integral cycle Binary Rate Modulation is applied to an ac voltage controller and this method of power dispatch, which displays an optimal ac cycle positioning property, is compared with Pulse …

A Silicon Knife Design And Fabrication, Mingli Wang

Theses

In this thesis, the design and fabrication of a silicon knife is described. The device design is based on the principle of oxidation sharpening.

The knife is made from a silicon wafer and can be made to be any chosen length up to 150 mm. It was made with the same basic procedures used in semiconductor chip manufacturing. This type of processing/manufacturing results in a knife with a high degree of sharpness and smoothness compared with existing knife technology.

The knife fabrication plan combines IC processing, techniques including anisotropic and isotropic etching of silicon, plasma dry etching and chemical etching …

A General Method For The Inverse Kinematics Of Rotational Displacements In Spatial Mechanisms, John D. Kliminski

Theses

An iterative technique was developed to solve the inverse kinematics problem for the joint rotations in both closed-loop and open-loop spatial mechanisms and robotic manipulators in any prescribed configuration. The method is based on fixing one link in space and maneuvering the other links to form a closed chain, following an approximation of the actual physical assembly of the mechanism. In order to apply the same principle to both types of mechanisms, an open-loop mechanism was modeled as a closed-loop mechanism by creating a fictitious fixed link in the free space between the base and the end of the chain …