Novel Method For Broadband On-Chip Noise Characterization, Mohammad Ghadiri Sadrabadi

Masters Theses

A novel method for on-chip noise characterization of mm-wave circuits is presented. Different available methods for noise measurements and requirements for on-chip noise mea-surements are studied. The Y-factor method is chosen to be the more suitable method for in-situ applications since it does not require absolute measurements. A state of the art CMOS noise source is implemented in 32nm SOI CMOS technology to enable the in-situ noise measurements of a 20-35 GHz reconfigurable low noise amplifier. Measurement results show that the ENR of the noise source is repeatable enough so that the calibration of the noise source is only required …

An Experimental Study Of The C-Start Of A Mechanical Fish, Benjamin Kandaswamy Chinna Thambi

Masters Theses

The Northern Pike have recorded the highest accelerations for marine propulsors. The mean peak acceleration and velocity for a number of trials were found to be 120 ms-2 and 4 ms-1 respectively (Harper and Blake 1990) for live fish. Here, we emulate this fast-start motion and analyze the performance of the Northern Pike, using a mechanical fish. The mechanical fish was made of a PVC head attached to a spring steel frame with aluminum ribs and a plastic tail. A latex rubber sheet was used as the skin of the fish. The set-up used air bearings for frictionless motion with …

Propagation Prediction Over Random Rough Surface By Zeroth Order Induced Current Density, Narayana Srinivasan Balu

Masters Theses

Electromagnetic wave propagation over random sea surfaces is a classical problem of interest for the Navy, and significant research has been done over the years. Here we make use of numerical and analytical methods to predict the propagation of microwaves over random rough surface. The numerical approach involves utilization of the direct solution (using Volterra integral equation of the second kind) to currents induced on a rough surface due to forward propagating waves to compute the scattered field. The mean scattered field is computed using the Monte-Carlo method. Since the exact solution (consisting of an infinite series) to induced current …

Investigating Teenage Drivers' Driving Behavior Before And After Lag (Less Aggressive Goals) Training Program, Jingyi Zhang

Masters Theses

Motor vehicle crashes are a leading cause of death during adolescence, with the fatal crash rate per mile-driven for 16-19 years old drivers being nearly 3 times larger than the rate for drivers age 20 and older. High gravitational events among teenage drivers, such as quick starts, and hard stops, have been shown to be highly correlated with crash rates. The current younger driver training programs developed in the late 1990s, however, do not appear to be especially effective in regard to many skills which are critical to avoiding crashes. With this in mind, a simulator-based training program aimed at …

Design Of A Passive Exoskeleton Spine, Haohan Zhang

Masters Theses

In this thesis, a passive exoskeleton spine was designed and evaluated by a series of biomechanics simulations. The design objectives were to reduce the human operator’s back muscle efforts and the intervertebral reaction torques during a full range sagittal plane spine flexion/extension. The biomechanics simulations were performed using the OpenSim modeling environment. To manipulate the simulations, a full body musculoskeletal model was created based on the OpenSim gait2354 and “lumbar spine” models. To support flexion and extension of the torso a “push-pull” strategy was proposed by applying external pushing and pulling forces on different locations on the torso. The external …

Impedance Measurement Of Small Antennas Over A Ground Plane Without Direct Cable Attachment, Yutong Yang

Masters Theses

An indirect impedance measurement approach that does not require direct cable attachment or large space using a two-port network is presented. Using a straight wire monopole as an interrogating antenna and measured impedances of three calibration standards, the input impedance of a small spherical helix dipole over a ground plane is retrieved. It is found that accurate result is obtained around the dipole resonance frequency. The accuracy and sources of error are discussed.

Single-Phase Turbulent Enthalpy Transport, Bradley J. Shields

Masters Theses

Vapor generation is central to the flow dynamics within fuel injector nozzles. Because the degree of atomization affects engine emissions and spray characteristics, quantification of phase change within diesel fuel injectors is a topic of design interest. Within the nozzle, the large pressure gradient between the upstream and downstream plena induce large velocities, creating separation and further pressure drop at the inlet corner. When local pressure in the throat drops below the fluid vapor pressure, phase change can occur with sufficient time. At the elevated temperatures present in diesel engines, this process can be dependent upon the degree of superheat, …

Design And Implementation Of A Network Service Marketplace, Yunsheng Qi

Masters Theses

The Internet has successfully served the world for more than three decades, while limitations and drawbacks still exist. A lot of researches have been done on innovation of Internet to address those inadequacies. One approach to improve Internet performance is to make choice as a principle in network architecture. We believe that a service-based network architecture with choice, or we call it ChoiceNet, is the most suitable option for future Internet. In this thesis, we design and implement a network service marketplace. Due to the flexibility and functionality of web application, the marketplace is implemented by a web application to …

Effect Of Clock And Power Gating On Power Distribution Network Noise In 2d And 3d Integrated Circuits, Vinay C. Patil

Masters Theses

In this work, power supply noise contribution, at a particular node on the power grid, from clock/power gated blocks is maximized at particular time and the synthetic gating patterns of the blocks that result in the maximum noise is obtained for the interval 0 to target time. We utilize wavelet based analysis as wavelets are a natural way of characterizing the time-frequency behavior of the power grid. The gating patterns for the blocks and the maximum supply noise at the Point of Interest at the specified target time obtained via a Linear Programming (LP) formulation (clock gating) and Genetic Algorithm …

Development Of A Support Structure For Multi-Rotor Wind Turbines, Gaurav Murlidhar Mate

Masters Theses

The earliest design of a wind power system with multiple rotors on a single support structure dates back to the late 1800s. Such a system called a Multi-Rotor Wind Turbine (MRWT) was proposed by several researchers due to its perceived advantages over a single-rotor wind turbine. As turbine size increases, power produced by a rotor tends to scale up as the square of its diameter, as opposed to rotor weight which varies as its cube. So, several smaller rotors will weigh and cost less than one large rotor producing the same power. MRWTs offer several advantages such as better distribution …

Effect Of Chemotherapeutic Treatment Schedule On A Tissue Transport Model, Dan E. Ganz

Masters Theses

Current chemotherapeutic treatment schedule prediction methods rely heavily on PK/PD-based models and overlook the important contribution of tissue-level transport and binding. Tissue-level transport and binding phenomena are essential to understanding drug delivery and efficacy in tumors. Drugs with desirable PK/PD properties often fail in vivo due to poor tissue-level transport. We developed an in silico method to predict the effect of treatment schedule on efficacy that couples PK/PD with tissue-level transport. Treatment schedules were implemented on theoretical drugs with different PK/PD and transport properties. For each drug with a given clearance rate, diffusivity, and binding, treatment schedules consisting of one …

Modeling Dynamic Stall For A Free Vortex Wake Model Of A Floating Offshore Wind Turbine, Evan M. Gaertner

Masters Theses

Floating offshore wind turbines in deep waters offer significant advantages to onshore and near-shore wind turbines. However, due to the motion of floating platforms in response to wind and wave loading, the aerodynamics are substantially more complex. Traditional aerodynamic models and design codes do not adequately account for the floating platform dynamics to assess its effect on turbine loads and performance. Turbines must therefore be over designed due to loading uncertainty and are not fully optimized for their operating conditions. Previous research at the University of Massachusetts, Amherst developed the Wake Induced Dynamics Simulator, or WInDS, a free vortex wake …

Buckling Of Particle-Laden Interfaces, Theo Dias Kassuga

Masters Theses

We study the buckling of an oil-water interface populated by micron-sized latex particles using a Langmuir trough. We extend pre-existing results to the micron-range with different capillary length and compare the experimental data to the existing theoretical framework. An unexpected trend for the dominant wavelength of buckling is observed, suggesting that there is a transition between regimes in the micron-range. A mechanism for the new regime is proposed. Cascading is reported, as well as novel kinds of transition between wavelengths within the same particle raft. Lastly, the effect of compression on the macroscopic arrangement of particles is investigated, as well …

Design And Control Of A Two-Wheeled Robotic Walker, Airton R. Da Silva Jr.

Masters Theses

This thesis presents the design, construction, and control of a two-wheeled inverted pendulum (TWIP) robotic walker prototype for assisting mobility-impaired users with balance and fall prevention. A conceptual model of the robotic walker is developed and used to illustrate the purpose of this study. A linearized mathematical model of the two-wheeled system is derived using Newtonian mechanics. A control strategy consisting of a decoupled LQR controller and three state variable controllers is developed to stabilize the platform and regulate its behavior with robust disturbance rejection performance. Simulation results reveal that the LQR controller is capable of stabilizing the platform and …

Ubot-7: The Design Of A Compliant Dexterous Mobile Manipulator, Jonathan Cummings

Masters Theses

This thesis presents the design of uBot-7, the latest version of a dexterous mobile manipulator. This platform has been iteratively developed to realize a high performance-to-cost dexterous whole body manipulator with respect to mobile manipulation. The semi-anthropomorphic design of the uBot is a demonstrated and functional research platform for developing advanced autonomous perception, manipulation, and mobility tasks. The goal of this work is to improve the uBot’s ability to sense and interact with its environment in order to increase the platforms capability to operate dexterously, through the incorporation of joint torque feedback, and safely, through the implementation of passive and …

Network-On-Chip Synchronization, Mark Buckler

Masters Theses

Technology scaling has enabled the number of cores within a System on Chip (SoC) to increase significantly. Globally Asynchronous Locally Synchronous (GALS) systems using Dynamic Voltage and Frequency Scaling (DVFS) operate each of these cores on distinct and dynamic clock domains. The main communication method between these cores is increasingly more likely to be a Network-on-Chip (NoC). Typically, the interfaces between these clock domains experience multi-cycle synchronization latencies due to their use of “brute-force” synchronizers. This dissertation aims to improve the performance of NoCs and thereby SoCs as a whole by reducing this synchronization latency.

First, a survey of NoC …

Were Neandertal Humeri Adapted For Spear Thrusting Or Throwing? A Finite Element Study, Michael Anthony Berthaume

Masters Theses

An ongoing debate concerning Neandertal ecology is whether or not they utilized long range weaponry. The anteroposteriorly expanded cross-section of Neandertal humeri have led some to argue they thrusted their weapons, while the rounder cross-section of Late Upper Paleolithic modern human humeri suggests they threw their weapons. We test the hypothesis that Neandertal humeri were built to resist strains engendered by thrusting rather than throwing using finite element models of one Neandertal, one Early Upper Paleolithic (EUP) human and three recent human humeri, representing a range of cross-sectional shapes and sizes. Electromyography and kinematic data and articulated skeletons were used …

Design Of Non-Uniform Linear Array Via Linear Programming And Particle Swarm Optimization And Studies On Phased Array Calibration, Hua Bai

Masters Theses

For a linear array, the excitation coefficients of each element and its geometry play an important role, because they will determine the radiation pattern of the given array. Side Lobe Level (SLL) is one of the key parameters to evaluate the radiation pattern of the array. Generally speaking, we desire SLL to be as low as possible. For the linear array with uniform spacing, there are some classic methods to calculate the excitation coefficients to make the radiation pattern satisfy the given requirements. For the linear array with non-uniform spacing, linear programming and particle swarm optimization are proposed to calculate …

Short And Long-Term Performance Of A Skewed Integral Abutment Prestressed Concrete Bridge, Rami Bahjat

Masters Theses

This study presents the behavior of a precast skewed integral abutment bridge (IAB) using the recently developed NEXT-F Beam section in particular. In order to understand the bridge response, a 3-dimensional finite element model of a bridge (Brimfield Bridge) was developed to examine the thermal effect on the response of the bridge structural components. Eighteen months of field monitoring including abutments displacements, abutment rotations, deck strains, and beam strains was conducted utilizing 136 strain gauges, 6 crackmeters, and 2 tiltmeters. The behavior of the NEXT beams during construction was examined by conducting hand calculation considering all factors that could affect …

Millimeter Wave Indium Phosphide Heterojunction Bipolar Transistors: Noise Performance And Circuit Applications, Metin Ayata

Masters Theses

The performance of III-V heterojunction bipolar transistors (HBTs) has improved significantly over the past two decades. Today’s state of the art Indium Phosphide (InP) HBTs have a maximum frequency of oscillation greater than 800 GHz and have been used to realize an amplifier operating above 600 GHz . In comparison to silicon (Si) based devices, III-V HBTs have superior transport properties that enables a higher gain, higher speed, and noise performance, and much higher Johnson figure- of-merit . From this perspective, the InP HBT is one of the most promising candidates for high performance mixed signal electronic systems.

New Generator Control Algorithms For Smart-Bladed Wind Turbines To Improve Power Capture In Below Rated Conditions, Bryce B. Aquino

Masters Theses

With wind turbines growing in size, operation and maintenance has become a more important area of research with the goal of making wind energy more profitable. Wind turbine blades are subjected to intense fluctuating loads that can cause significant damage over time. The need for advanced methods of alleviating blade loads to extend the lifespan of wind turbines has become more important as worldwide initiatives have called for a push in renewable energy. An area of research whose goal is to reduce the fatigue damage is smart rotor control. Smart bladed wind turbines have the ability to sense aerodynamic loads …

Turbulent Transition In Electromagnetically Levitated Liquid Metal Droplets, Jie Zhao

Masters Theses

The condition of fluid flow has been proven to have a significant influence on a wide variety of material processes. In electromagnetic levitation (EML) experiments, the internal flow is driven primarily by electromagnetic forces. In 1-g, the positioning forces are very strong and the internal flows are turbulent. To reduce the flows driven by the levitation field, experiments may be performed in reduced gravity and parabolic flights experiments have been adopted as the support in advance. Tracer particles on the surface of levitated droplets in EML experiment performed by SUPOS have been used to investigate the transition from laminar to …

The Optimization Of Offshore Wind Turbine Towers Using Passive Tuned Mass Dampers, Onur Can Yilmaz

Masters Theses

Increasing energy demand and carbon emissions have driven the development of alternative energy solutions. One promising technology is wind energy. Wind energy technology developments has advanced substantially since the 1980s. Offshore wind turbines have become a major research focus, due to the promising offshore wind resource. However, challenges in offshore wind energy have arisen due to the additional wave loading and strong wind loads. Structural control systems have been implemented and researched in order to decrease dynamic response of these systems. The previous studies were successful at decreasing fatigue loads in the tower and support structure of offshore wind turbines. …

Cfd Simulation Of The Flow Around Nrel Phase Vi Wind Turbine, Yang Song

Masters Theses

The simulation of the turbulent and potentially separating flow around a rotating, twisted, and tapered airfoil is a challenging task for CFD simulations. This thesis describes CFD simulations of the NREL Phase VI turbine that was experimentally characterized in the 24.4m X 36.6m NREL/NASA Ames wind tunnel. All computations in this research are performed on the experimental base configuration of 0^o yaw angle, 3^o tip pitch angle, and a rotation rate of 72 rpm. The significance of specific mesh resolution regions to the accuracy of the CFD prediction is discussed. The ability of CFD to capture bulk quantities, …

Field And Analytical Studies Of The First Folded Plate Girder Bridge, Man Hou Sit

Masters Theses

Integral abutment bridges are very common for short span bridges in the United State due to their less construction and maintenance cost and generally good performance. This thesis studies the first integral abutment bridge using Folded Plate Girder (FPG) Bridge System. The bridge is instrumented with a variety of gauges to capture the behavior of the bridge, and a total of two year and one month [11/2011~12/2013] of data are collected and long-term data monitoring is performed. Live load test and long term temperature effect on the bridge are studied using finite element modeling and compared with actual field data. …

Design And Evaluation Of An L-Band Current-Mode Class-D Power Amplifier Integrated Circuit, Michael J. Shusta

Masters Theses

Power amplifiers (PAs) convert energy from DC to high frequencies in all radio and microwave transmitter systems be they wireless base stations, handsets, radars, heaters, and so on. PAs are the dominant consumers of energy in these systems and, therefore, the dominant sources of system cost and inefficiency. Research has focused on efficient solid-state PA circuit topologies and their optimization since the 1960s. The 2000s saw the current-mode class-D (CMCD) topology, potentially suitable for today's wireless communications systems, show promise in the UHF frequency band. This thesis describes the design and testing of a high-efficiency CMCD amplifier with an integrated …

Kinetics Of Aluminization And Homogenization In Wrought H-X750 Nickel-Base Superalloy, Sean Reilly

Masters Theses

In sub-millimeter sheets of wrought H-X750 Nickel-base superalloy, aluminum-rich coatings are bonded to matrix with a vapor phase aluminization process. If an appropriate amount of aluminum is bonded to matrix with homogenization treatment, the resulting diffusion couple will diffuse into coherent (g/g’) heterogeneous phases creating matrix that is both precipitation and solid solution strengthened.

The diffusional mechanisms for solid solution mass transport involved with the growth and dispersion of bonded aluminum-rich coatings in the aluminization process only differ from the no external mass flow homogenization process with annealing treatment in that the boundary conditions are different. In each case these …

A Consistent Algorithm For Implementing The Space Conservation Law, Venkata Pavan Pillalamarri Narasimha Rao

Masters Theses

Fluid flows occurring in moving and/or deforming environments are influenced by the transient nature of their containment. In Computational Fluid Dynamics (CFD), simulating such flow fields requires effort to maintain the geometric integrity of the transient flow domain. Convective fluxes in such domains are evaluated with respect to the motion of the boundaries of the control volume. These simulations demand conservation of space in addition to the conservation of mass, momentum and energy as the solution continues in time.

The Space Conservation Law in its continuous form can be inferred by using the rules of fundamental calculus. However, implementing it …

Measurement And Verification - Retro-Commissioning Of A Leed Gold Rated Building Through Means Of An Energy Model: Are Aggressive Energy Simulation Models Reliable?, Justin M. Marmaras

Masters Theses

During the construction of the new 3 story, 25,000+ square foot police station, a decision was made to participate in the LEED program to ensure the building had low operating costs, reduced emissions, conserved water and overall energy. The design of the building includes a primary-secondary ground source heat pump (GSHP) loop, a Dedicated Outside Air System (DOAS) with Energy Recovery Ventilation (ERV) wheel, all controlled by CO2 monitoring through Demand Control Ventilation (DCV) to supply heat pumps located in each space; all monitored by a Building Automation System (BAS).

The building’s future energy performance was predicted through an energy …

Metabolic Modeling Of Secondary Metabolism In Plant Systems, Lisa M. Leone

Masters Theses

In the first part of this research, we constructed a Genome scale Metabolic Model (GEM) of Taxus cuspidata, a medicinal plant used to produce paclitaxel (Taxol®). The construction of the T. cuspidata GEM was predicated on recent acquisition of a transcriptome of T. cuspidata metabolism under methyl jasmonate (MJ) elicited conditions (when paclitaxel is produced) and unelicited conditions (when paclitaxel is not produced). Construction of the draft model, in which transcriptomic data from elicited and unelicited conditions were included, utilized tools including the ModelSEED developed by Argonne National Laboratory. Although a model was successfully created and gapfilled by ModelSEED …