Engineering Commons^™

Estimating Electromagnetic Emissions From A Site Installation With Multiple Racks Of Server Equipment, Ze Sun

Masters Theses

“There are hundreds, sometimes even thousands, of servers working simultaneously inside a data center. Their radiation can be a problem and cause EMI issues. However, it is not feasible to perform full-wave simulation of these racks because of the large electric size of the model. In this thesis, an algorithm is proposed to predict the emission form rack array. The equivalent dipole source is extracted from EMI measurement data of a single rack and used as the radiation source in the multiple rack model. The coupling between racks cannot be ignored, but through the simulation, it is also found that …

Influence Of Pumping Parameters On The Freeze-Thaw And Scaling Resistance Of Highly Workable Concrete, Alexandra Nicole Wehar

Masters Theses

“Over the past 60 years, pumping concrete has gained popularity due to the economic and technical benefits that typically accompanies it. However, boom configuration and flow rate can adversely affect freeze-thaw and scaling resistance of concrete due to the effects of pressure on the air-void system. Therefore, the objective of this research is to assess the influence of different pumping parameters on the durability of hardened self-consolidating concrete. Self-consolidating, flowable, and conventional concrete mixtures were tested during large scale pumping experiments positioning the pump boom in an “A” and a flat shape as well as using different pumping speeds. In …

Multiphysics Prediction Model Of Microwave Curing For Thick Polymer Composites, Siva Dasari

Masters Theses

"Microwave curing technologies have many advantages over the traditional thermal curing methods for the manufacturing of fiber reinforced polymers, especially the processing speed and energy efficiency. Energy can be instantaneously transferred through applied electromagnetic fields and heat is generated based on dipolar rotational interactions. Microwave curing processes have been used for glass fiber composites but there are significant challenges associated with microwave curing of carbon fiber composites. Efficient heating may be difficult due to high dielectric loss associated with carbon fibers. Laminate quality will be highly dependent on the uniformity of the electromagnetic field in the material. In this work, …

Development Of Castrip Dual Phase Steel, Brenton Allen Hrebec

Masters Theses

“Thermomechanical processing necessary to produce DP 980 steel using CASTRIP hot band was investigated. The resultant steel has an ultimate tensile strength of 1038 MPa, yield strength of 744 MPa, and total elongation of 8.6%. These mechanical properties were achieved by batch annealing the hot band at 649°C for 48 hours and cold rolling to a 20% reduction. The steel was continuously annealed to simulate a galvanization cycle with an intercritical temperature of 810°C. The possibility of improving the texture of the steel by warm rolling under dynamic strain aging conditions was investigated. Dynamic strain aging in the CASTRIP hot …

Performance Of One-Part And Two-Part Class C Fly Ash-Based Alkali Activated Mortars, Cedric Chani Kashosi

Masters Theses

“Seeking an eco-friendly concrete, researchers have conducted studies to fully replace ordinary Portland cement (OPC) with fly ash (FA) producing alkali-activated concrete (AAC). Results showed better performance of AAC in terms of high early compressive strength, and durability compared to conventional concrete. However, much is still unknown about the behavior of AAC. From the type of materials used, the curing procedure, and long-term strength development of these binders; a thorough investigation is needed in order to fill the existing gap from previous studies and thus make a step forward to the safely use of AAC in the construction industry. The …

Laser Machining Countersinks In Carbon Fiber Reinforced Polymer, Leon James Neely Hill

Masters Theses

“Laser machining countersinks with a frequency doubled Q-switched diode pumped Nd:YAG laser is demonstrated. Tests were conducted in 0.100" thick IM7 prepreg CFRP with [0,90]3S orientation. The HAZ is minimized to avoid stress concentrations in the epoxy matrix. A chamber and filtration system was designed and built to contain the byproducts produced in the machining process. The variables investigated are the number of repetitions in the offset path, the plunge rate, and the line energy. The research was performed over one baseline study, one parameter space exercise, two full factorial experiments, and one repeatability study. Assessment was done under an …

The Effect Of Cell Size And Surface Roughness On The Compressive Properties Of Abs Lattice Structures Fabricated By Fused Deposition Modeling, Leah Hope Mason

Masters Theses

"Postprocessing is an important step in many manufacturing methods, but it is especially important for additive manufacturing. Researchers looking to improve the surface roughness of acrylonitrile butadiene styrene (ABS) parts fabricated by fused deposition modeling (FDM) have determined that acetone smoothing not only achieves improved surface roughness but increases compressive strength as well. This could be very beneficial to lattice structures, which are known for already having an excellent strength to weight ratio. If the compressive strength of ABS lattice structures could be improved even further using acetone smoothing, it could expand the applications for plastic lattice structures and improve …

Unmanned Aerial And Traversing Vehicle -- A Mobile Platform For Bridge Inspections, Clayton A. Fritsche

Masters Theses

“Unmanned aerial vehicles (UAVs), also known as drones, have been rapidly growing in popularity since their creation. This study aimed to create a robotic platform used to assist in the inspection process of the nation’s aging and deteriorating bridges. To this end, a multimodal inspection robot that utilized both flying and driving technologies, was designed, analyzed, and tested for aerial, traversing, and their transitional operability. The design, herein referred to as the “BridgeBot”, was evaluated both computationally and experimentally. A finite element model of the BridgeBot was established and analyzed under static loading scenarios to help determine stress distributions and …

Development Of Test Methods For Characterizing Extrudability Of Cement-Based Materials For Use In 3d Printing, Jonathan Thomas Kuchem

Masters Theses

"3D printing is the process of creating three-dimensional objects using an automated additive manufacturing process. The 3D printing process has been used with materials such as metals and polymers, but application with cement based materials for the construction industry has yet to be developed. In this research, two main problems were investigated for printing cement based composite materials: extrudability and tensile reinforcement. Fiber-reinforced concrete (FRC) was studied as an internal reinforcing system to increase tensile/flexural strength. First, FRC was studied to investigate mechanical properties and use of fibers from waste tires as an environmentally friendly option. A reference mixture with …

Evaluation Of Naturally Occurring And Anthropogenic Contamination In Missouri Streams, Christina Jane Sehrt

Masters Theses

"The goal of this study is to observe the values and variability of water quality parameters and benthic macroinvertebrates in watersheds with very little anthropogenic impact and to compare these values with those acquired in watersheds with more anthropogenic impact. The following five HUC 12-digit watersheds had very little anthropogenic impact and were considered "pristine": Rogers Creek, Mill Creek, Middle West Fork-Black River, Bee Fork, and Ottery Creek. Five largely urban sub-basins were also considered; these basins are: Grand Glaize Creek, Glaize Creek, Sugar Creek, Hominy Creek, and Grindstone Creek. For each watershed, both water quality parameters and benthic macroinvertebrates …

Unified Probe Launch Pattern Design And Methodology Of Differential Probe Characterization, Han Deng

Masters Theses

"Differential probe is wildly used in the signal integrity area to do the accuracy signal measurement in frequency domain or time domain. Comparing with traditional SMA connector measurement, the probe measurement has several advantages such as the high flexibility and measurement efficiency. Nevertheless, the probe has some disadvantages such as multiple design patterns and the difficulty of fast landing. In this thesis, a unified probe landing pattern is provided to solve the con of probes and a probe testing fixture is designed for characterize probe and extract the probe model.

In the first portion, a unified differential probe launching pattern …

Modeling Impact Of Glass Weave On Differential Phase Skew By Design Of Experiments Method, Feng Zhang

Masters Theses

"The glass weave structure of a manufactured Printed Circuit Board (PCB) is scanned under a Scanning Electron Microscope (SEM), with top-down and cross-sectional views. Previously, analytical methods were used to investigate the glass-weave effect on transition properties in a PCB. Based on the SEM observation, this study was conducted to build full-wave models using various glass-weave types and different relative positions between differential traces and glass-weave bundles. This study aims to obtain the relationship between the glass weave and trace geometry, and the phase skew of the differential trace by using Design of Experiment (DoE) method and simulation results"--Abstract, page …

Experimental Characterization Of Common-Mode Sources For Prediction Of System Level Common-Mode Current On Cable Harnesses, Sameer Sudha Arun Walunj

Masters Theses

"Common-mode current on cable harnesses is often the primary source of radiated emissions below several hundred megahertz. It is difficult, however, to estimate common-mode currents that will occur in a system from component level tests because the common-mode impedances are different in the system. Research presents two methods for using simple component level tests to estimate equivalent common-mode source voltages and source impedances responsible for generating common-mode current. Key to these methods is assuming the harness can be represented with two transmission lines, one terminated with a short and one with an open. Equivalent sources are predicted for those circuits …

Performance Evaluation Of Bmi Resin System For Thin-Ply Composites, Manoj Kumar Reddy Rangapuram

Masters Theses

"Composites materials are increasingly being used in aerospace applications over the past few years. The unique properties like high strength to weight ratio, thermal stability, fatigue and corrosion resistance set them apart from the conventional materials. Composite materials are well suited for the applications where weight is the primary concern in the design. Composites structures are vulnerable to mechanical as well as thermal loadings. Transverse micro-cracking and delamination are the most common type of failures in composite materials. The thickness of the ply being used play a key role dictating the properties of the resultant composite structure. As the ply …

Methane Dry Reforming Reaction On Cr, V, In, And Ga Supported Sapo-34 Zeolite, Ehigiator Festus Ojo

Masters Theses

”The CO₂ reforming of methane is a significant research area in mitigating and transforming two greenhouse gases for the production of syngas. The reaction has been investigated for four different promoted catalysts to determine their reactant's conversion, product’s selectivity, and their respective syngas ratios.

The catalytic test was investigated under atmospheric conditions at 600⁰C for 6.5h with a WHSV of 4800 ml g^-1 h^-1. The conversion and selectivity of catalysts 9Al 1V-inc SAPO-34, 9Al 1Cr-inc SAPO-34, 9Al 1Ga-inc SAPO-34, and 9Al 1In-inc SAPO-34 were analyzed. The CH₄ conversion for the different catalysts are, 9Al 1Cr-inc …

Controlled Switching In Kalman Filtering And Iterative Learning Controls, He Li

Masters Theses

“Switching is not an uncommon phenomenon in practical systems and processes, for examples, power switches opening and closing, transmissions lifting from low gear to high gear, and air planes crossing different layers in air. Switching can be a disaster to a system since frequent switching between two asymptotically stable subsystems may result in unstable dynamics. On the contrary, switching can be a benefit to a system since controlled switching is sometimes imposed by the designers to achieve desired performance. This encourages the study of system dynamics and performance when undesired switching occurs or controlled switching is imposed. In this research, …

Light Touch Based Virtual Cane For Balance Assistance During Standing, Sindhu Reddy Alluri

Masters Theses

"Can additional information about one's body kinematics provided through hands improve human balance? Light-Touch (LT) through hands helps improve balance in a wide range of populations, both healthy and impaired. The force is too small to provide any meaningful mechanical assistance -- rather, it is suggested that the additional sensory information through hands helps the body improve balance.

To investigate the potential for improving human balance through biofeedback through hands, we developed a Virtual Cane (VC) for balance assistance during standing. The VC mimics the physical cane's function of providing information about one's body in space. Balance experiments on 10 …

Removal Of Antimony And Bismuth From Copper Electrorefining Electrolyte By Two Proprietary Solvent Extraction Extractants, Andrew Artzer

Masters Theses

"Antimony and bismuth are two of the most problematic impurities in copper electrorefining (ER). Because of this, much research has been done investigating the ways to remove them. Processes that are currently being used industrially include anode additions, liberators, ion exchange (IX), and solvent extraction (SX). Of these, liberators and anode additions are the most common while SX is the least, mostly being used for arsenic removal. There are other methods that have been evaluated, but are not in commercial use. These include the use of various electrolyte additives, and adsorbents such as bentonite clay and heavy metal sulfates.

Two …

Asphaltene Stability In Crude Oil During Carbon Dioxide Injection And Its Impact On Oil Recovery: A Review, Data Analysis, And Experimental Study, Sherif M. Fakher

Masters Theses

"Crude oils are usually associated with many compounds, some of which are favorable and others, which are not. One of the most unfavorable components of crude oil that pose severe operational problems and decreases oil production significantly are asphaltenes. These compounds are solids that are homogenized in the crude oil at room temperature but tend to separate from solution when agitated. They can deposit in the reservoir pores, wellbore, and transportation pipelines thus causing severe operational problems and oil recovery reduction.

Even though researchers have been studying asphaltenes for more than 100 years, there is still an ambiguity concerning asphaltene …

High-Speed Pcb Trace Design Using A Behavioral Surface Roughness Model And High-Speed Test Coupon Design With Non-Functional Pads, Han Gao

Masters Theses

"In high-speed digital systems as data rates increase to tens of gigabits per second, the loss from the conductor surface roughness cannot be ignored. Djordjeic and Huray roughness model is widely used to count for the conductor roughness loss. However the practical application of the existed models are not straight forward since the frequency-dependent dielectric loss is usually unknown, leading to high discrepancies at high frequencies (above 10 GHz). To solve this problem, a behavioral model was developed by adding a dispersive term to the dielectric. The dispersive term in the model captures dispersion behavior observed in the measurement accurately. …

Investigating The Use Of Class C Flyash-Based Geopolymer Cement As A Potential Alternative To Portland Cement To Seal Co₂ Storage Wells, Priyesh Parimal Jani

Masters Theses

"Capturing emitted carbon dioxide from the source of emission and storing it underground is one effective way to reduce the amount of CO₂ in the atmosphere and is called carbon capture and storage (CCS). For the successful CCS project, it is necessary to ensure long term storage of injected CO₂ inside these selected reservoirs. Portland cement used to cast wells in these reservoirs degrade in CO₂ environment and can create migration path for leakage of CO₂. The aim of this study was to provide a comprehensive review about the problem, to propose a new geopolymer …

Routing Algorithm For The Ground Team In Transmission Line Inspection Using Unmanned Aerial Vehicle, Yu Li

Masters Theses

"With the rapid development of robotics technology, robots are increasingly used to conduct various tasks by utility companies. An unmanned aerial vehicle (UAV) is an efficient robot that can be used to inspect high-voltage transmission lines. UAVs need to stay within a data transmission range from the ground station and periodically land to replace the battery in order to ensure that the power system can support its operation. A routing algorithm must be used in order to guide the motion and deployment of the ground station while using UAV in transmission line inspection. Most existing routing algorithms are dedicated to …

Effects Of Uncertainty Refinement On Satellite Collision Probability, Bruce Thomas Morrison

Masters Theses

"Due to the drastic increase in orbital debris about the Earth, the likelihood for new and current mission satellites to collide with other objects grows. When a mission satellite is placed in a highly populated orbit in the vicinity of other satellites or debris, it is necessary to consider the probability of collision to assess any possible conjunctions. The computation of the collision probability is heavily dependent on the relative position and velocity of the objects during conjunction, as well as the combined covariance. There are two main types of analytic collision probability computations; the first assumes that the objects …

A Study On End-Anchorage And Bond Behavior Of Steel-Fiber Reinforced Cementitious Matrix Composites Externally Bonded To A Concrete Substrate, Christopher Michael Moore

Masters Theses

"Fiber reinforced cementitious matrix (FRCM) composites are a strengthening material consisting of continuous fibers embedded in an inorganic matrix that have the potential to provide additional flexural and shear strength to concrete and masonry members. When used for external strengthening, however, debonding of the material is often observed due to slippage of the fiber with respect to the matrix, causing loss of composite action and a reduction in load carrying capacity. The composite utilized in this study consisted of continuous steel fibers embedded in an inorganic cementitious matrix bonded to a concrete prism. Additionally, an end-anchorage system was implemented with …

Program Management For Concurrent University Satellite Programs, Including Propellant Feed System Design Elements, Shannah Withrow-Maser

Masters Theses

"Propulsion options for CubeSats are limited but are necessary for the CubeSat industry to continue future growth. Challenges to CubeSat propulsion include volume/mass constraints, availability of sufficiently small and certified hardware, secondary payload status, and power requirements. A multi-mode (chemical and electric) thruster was developed by at the Missouri University of Science and Technology to enable CubeSat propulsion missions. Two satellite buses, a 3U and 6U, are under development to demonstrate the multi-mode thruster's capabilities. Two key challenges related to these missions are the development of the feed system to support the thruster and management of the two bus programs' …

Computational Fluid Dynamics Modeling Of Proppant Static Settling Velocity In High Viscosity Friction Reducers, Chen Yuan

Masters Theses

"In the current petroleum fracturing industry, it is necessary to understand the downhole migration and settling velocity of the proppant. If we can master this information well, it will be a great help to obtain effective propped fracture conductivity. In order to study the transport of proppants in the well, we used laboratory experiments and computer numerical simulations to compare the results to get a meaningful conclusion. We spent a lot of time building models on a powerful computer and comparing the experimental conclusions. We finally decided to use computational fluid dynamics (CFD) as the simulation platform, discrete phase method …

Gel Composition And Brine Concentration Effect On Hydrogel Dehydration Subjected To Uniaxial Compression, Xinrui Zhao

Masters Theses

"Gel treatment is a process that injects the gel into a reservoir to control the conformance and improve the sweep efficiency of injection fluids. At a certain pressure gradient, the gel dehydrates in a reservoir due to mechanical forces. This work evaluates the effects of the gel composition and brine concentration on gel dehydration under uniaxial compression. A sodium acrylate-co-acrylamide based gel cross-linked with N, N'-Methylenebisacrylamide (MBAA) was used for the study. The compression test is performed with a rheometer with a plate-plate geometry. The gel dehydration under pressure was measured to see how gel dehydration would be impacted by …

Coupling Path Visualization Based On Reciprocity Theorem, Yang Zhong

Masters Theses

"A new method to visualize coupling path is proposed to help solve EMI problems. Based on the reciprocity theorem and the concept of reaction, coupling coefficient (CC) is defined to characterize coupling power density. For two-port networks, surface integral of CC can represent coupled voltage on the open-circuited port or coupled power on the loaded port. For dipole-moment based systems, surface integral of CC can represent coupled field components. The calculated CC should be a complex scalar at each point. By properly adjusting the excitation phases, the imaginary part of surface integral of CC will be zero and thus can …

Breaker Evaluation And Formation Damage Remediation Of Re-Crosslinkable Preformed Particle Gel (Rppg), Enze Zhou

Masters Theses

"Re-crosslinkable preformed particle gel (RPPG) is a newly developed preformed particle gel for improving sweep efficiency and oil recovery by blocking or reducing the conductivity of fractures and fracture-like channels or conduits. However, RPPG has the potential to plug the facilities or damage the formation if a treatment is not properly conducted.

This work presents the performance of selected oxidizing breakers on the degradation of RPPG. The influence of a few factors on the degradation process was investigated, including breaker type, breaker concentration, temperature, gel concentration, gel aging time, and gel size. Results indicate that breaker type, concentration, and temperature …

Using The Ert Method To Differentiate Resistivity Anomalies Attributed To Natural And Man-Made Activities, Ibrahim Faisal Alshareef

Masters Theses

"Karst terrain is considered to be a very complex topography compared with most other geological environments. Many features can be observed such as sinkholes, air-filled cavities, losing streams, and solution widened joints. These karst features can cause subsidence and damage infrastructure such as buildings and roads thus causing economic hardship and disruption of life. The typical geological and hydrological studies are not enough to understand the karst processes.

For this reason, two geophysical methods were involved in investigating the subsurface in the study area. In this research, the electrical resistivity tomography (ERT) and multichannel analysis of surface wave (MASW) data …