Engineering Commons^™

How Airport Construction Will Evolve With The Increased Effects Of Climate Change, Xavier M. Ashley

Beyond: Undergraduate Research Journal

This report addressed the effects rising global temperatures resulting from climate change have had on flight operations in their entirety. The research objective was to discover what methods could enhance climate adaptation in airport construction, as higher mean-surface temperatures have an increasingly negative effect on aircraft performance. The findings would primarily be of interest to the Federal Aviation Administration (FAA) Primary Office presiding over the planning and development of airports. Overall, the report provided a comprehensive analysis of global warming’s effects on aviation, including the implications of degraded aircraft performance and sea-level rise for coastal airports. Additionally, it examined comparative …

Cleared To Land: Pilot Visual Detection Of Small Unmanned Aircraft During Final Approach, Ryan J. Wallace, Samuel M. Vance, Jon M. Loffi, Jamey Jacob, Jared C. Dunlap, Taylor A. Mitchell, Robert Thomas, Seabrook R. Whyte

International Journal of Aviation, Aeronautics, and Aerospace

Sighting reports of unmanned aircraft systems (UAS) by pilots, air traffic controllers, and other aviation stakeholders have continued to rise since the Federal Aviation Administration (FAA) began tracking in 2014. In 2018, the FAA received 2,307 such reports, with 22.8% (n = 526) occurring during the final approach phase of flight. The threat of a midair collision between a manned aircraft and UAS is heightened during the final approach phase of flight, as the aircraft transitions from higher-altitude airspace to the low-altitude arena, now shared with drones. Absent UAS sense and avoid systems, pilots are forced to rely on …

Mass Evacuation Effects On Transportation: A Comparative Analysis, Emily M. Jannace

Beyond: Undergraduate Research Journal

Mass evacuations have changed greatly in the past two decades. Evacuations such as Louisiana during Hurricane Katrina, Florida during Hurricane Irma, and New York during the 9/11 Terrorist Attacks, Hurricane Sandy, and Hurricane Irene have had significant impacts on future mass evacuations in terms of transportation. This paper takes these methods and analyzes the best approach in given situations based on volume capacity, impact, and cost to make recommendations that can be used by the three previously mention municipalities. With so many different techniques available, it is important to choose the one that moves the most people out of harm’s …

Forward Osmosis Flow Rate Differential Using Different Osmotic Agents, John M. Trzinski

Beyond: Undergraduate Research Journal

Life support is one of the most vital systems flown on manned spaceflight missions. The systems currently used are large, heavy, inefficient, and power consuming in an environment that requires nearly perfect conditions to function. Forward Osmosis (FO) is a form of filtration that uses the natural properties of water and concentration gradients to filter water without the need for any electricity. An experiment was conducted during the Embry Riddle Summer 2018 study abroad to the LUNARES research station in Piła, Poland. This experiment explored how the flow rate of water through a FO filtration system could be affected by …

Chip-Off Success Rate Analysis Comparing Temperature And Chip Type, Choli Ence, Joan Runs Through, Gary D. Cantrell

Journal of Digital Forensics, Security and Law

Throughout the digital forensic community, chip-off analysis provides examiners with a technique to obtain a physical acquisition from locked or damaged digital device. Thermal based chip-analysis relies upon the application of heat to remove the flash memory chip from the circuit board. Occasionally, a flash memory chip fails to successfully read despite following similar protocols as other flash memory chips. Previous research found the application of high temperatures increased the number of bit errors present in the flash memory chip. The purpose of this study is to analyze data collected from chip-off analyses to determine if a statistical difference exists …

The Effect Of Experiential Education On Pilots' Vfr Into Imc Decision-Making, Geoffrey R. Whitehurst, Lori Brown, William G. Rantz, Dominic Nicolai, Jessica M. Bradley

Journal of Aviation/Aerospace Education & Research

In aviation, safety is always a primary consideration, and this is especially true during a pilot’s flight training to instill that safety mentality. However, this means that pilots are restricted by safety policies from encountering difficult weather situations during their training, which could, potentially, improve their weather decision-making skills for avoiding future hazardous weather encounters. Thirty-six general aviation pilots of varying instrument flight experience (IF) were allocated, using stratified random sampling based on their IF, to one of three groups, a control group and two educational treatment intervention groups. The educational treatment interventions were designed to improve the participant’s ability …

Double Stud Cargo Fitting Research, Alternative Cargo Clip Design And Analysis, Cemal İrfan Çalişkan, Ebubekir Koç Dr, Hamaid Mahmood Khan Dr, Mustafa Enes Bulduk

International Journal of Aviation, Aeronautics, and Aerospace

It can be said that today's civil aviation basics began to be laid in the 1950s. This date is also important as the period in which the rules are being written and at the same time, some system solutions are produced by testing the methods of cargo loading. The cargo clip used in these cargo loading systems will be the subject of our article. In this context, the development process of the clip, which started in 1953 until today, will be examined in the light of the patent applications of the period; Afterwards, alternative clip-on work to the current cargo …

Design And Simulation Of Regional Navigation Constellation With Optimized Mean Dop Based On Hybrid Geo And Igso Satellites, Firooz Keyvani, Seyed Hosein Torabi

International Journal of Aviation, Aeronautics, and Aerospace

In this article, achieving an optimal layout of satellite constellation has been investigated with the aim of navigation (positioning) and with the least amount of error in a region coverage. In navigation, a parameter defined as DOP specifies influences of the geometry of satellite placement in space on position error. Less DOP means more precise navigation, and an attempt has been made in this study to minimize it. In the optimization phase, using genetic algorithm, the number of moments in which coverage is less than four reached zero and then the DOP parameter was minimized. Subsequently, the issue was studied …

Speech Interfaces And Pilot Performance: A Meta-Analysis, Kenneth A. Ward

International Journal of Aviation, Aeronautics, and Aerospace

As the aviation industry modernizes, new technology and interfaces must support growing aircraft complexity without increasing pilot workload. Natural language processing presents just such a simple and intuitive interface, yet the performance implications for use by pilots remain unknown. A meta-analysis was conducted to understand performance effects of using speech and voice interfaces in a series of pilot task analogs. The inclusion criteria selected studies that involved participants performing a demanding primary task, such as driving, while interacting with a vehicle system to enter numbers, dial radios, or enter a navigation destination. Compared to manual system interfaces, voice interfaces reduced …

Ultrafine Aluminium: Quench Collection Of Agglomerates, Tejasvi K, Y Pydi Setty, Vemana Venkateswara Rao

International Journal of Aviation, Aeronautics, and Aerospace

Combustion of aluminized solid propellants exhibits phenomena associated with accumulation, agglomeration, ignition, and combustion of ultra-fine aluminium particles. In this study, agglomeration phenomenon of ultra-fine aluminium in solid propellant combustion is investigated using quench collection experimental technique over the pressure ranges from 2MPa to 8MPa. The ultra-fine aluminium powder synthesized by Radio Frequency Induction Plasma technique having harmonic mean size of 438nm is used for agglomeration study. The quenching distance is varied from 5mm to 71mm from the propellant burning surface to estimate the effect on agglomerate size. The morphology and chemical compositions of the collected products were then studied …

Urban Flow And Small Unmanned Aerial System Operations In The Built Environment, Kevin A. Adkins

International Journal of Aviation, Aeronautics, and Aerospace

The Federal Aviation Administration (FAA) has put forth a set of regulations (Part 107) that govern small unmanned aerial system (sUAS) operations. These regulations restrict unmanned aircraft (UA) from flying over people and their operation to within visual line of sight (VLOS). However, as new applications for unmanned aerial systems (UAS) are discovered, their capabilities improve, and regulations evolve, there is an increasing desire to undertake urban operations, such as urban air mobility, package delivery, infrastructure inspection, and surveillance. This built environment poses new weather hazards that include enhanced wind shear and turbulence. The smaller physical dimensions, lower mass and …

Fe Modeling Methodology For Load Analysis And Preliminary Sizing Of Aircraft Wing Structure, Jun Hwan Jang, Sang Ho Ahn

International Journal of Aviation, Aeronautics, and Aerospace

It is a critical part at the basic design phase of aircraft structural design to build a finite element model and it will have a direct impact on time and cost for airframe structure development. In addition, the objective of finite element model will be varied depending on each design review phase and the modelling methodology varied accordingly. In order to build an effective and economic finite element model, it is required to develop adequate level of modelling methodology based on each design phase and its objectives. Therefore, in this paper, the finite element modeling methodology was presented for internal …

Satellite Maintenance: An Opportunity To Minimize The Kessler Effect, Bettina M. Mrusek Dr.

International Journal of Aviation, Aeronautics, and Aerospace

Recently, there has been an emphasis on the growing problem of orbital debris. While the advantages of placing satellites into space are numerous, advances in satellite technology combined with the growth of the industry have resulted with a significant amount of debris in the orbits surrounding our planet. The harshness of the space environment has also contributed to the debris, as evidenced by the number of objects currently in orbit which are not operational. As the amount of debris grows, so too does the likelihood of collisions, ultimately culminating in the Kessler Effect. However, recent advances in propulsion, advanced navigation, …

Aircraft Interior Design And Satisfaction For Different Activities; A New Approach Toward Understanding Passenger Experience, Golnoosh Torkashvand, Lucas Stephane, Peter Vink

International Journal of Aviation, Aeronautics, and Aerospace

Among airlines and aircraft manufacturers there is much attention for passenger experience. However, there is not much literature on how the activities of passengers can be supported by the aircraft interior. The current study focuses on the need finding and requirements analysis of flight passengers. Twenty-three activities were defined based on retrospective interviews and brainstorming sessions. Respondents were asked to rate their overall perception related to the importance of each of those 23 activities on a Linkert scale, from “not at all important” to “extremely important”. On a separate question they were also asked to rate their overall satisfaction by …

Crew Resource Management For Large Unmanned Aircraft Systems Operations, Peter S. Neff

International Journal of Aviation, Aeronautics, and Aerospace

Abstract

The author explored the application of crew resource management (CRM) principles to commercial flight operations conducted by large unmanned aircraft systems (UAS). Currently, there is no regulatory structure governing the operation of large UAS in commercial flight operations. However, the National Aeronautics and Space Administration (NASA) forecasted the future by demonstrating the feasibility of large remotely piloted UAS flight in June 2018 by flying Ikhana, a modified MQ-9 Predator B aircraft, over a 415-mile route in Class A and in Class E airspace over southern California (Kooser, 2018). Ikhana is a 10,500-pound aircraft with a wingspan of 66 feet …

Simulations On Optimization Of Liquid Spray Burners & Operating Parameters, Pallavi Gajjar, Vinayak Malhotra

International Journal of Aviation, Aeronautics, and Aerospace

Spray burners form an essential part of any liquid propulsion system as they are responsible for injecting, atomizing, mixing and combusting the liquid fuel. Spray combustion used in aerospace applications like the liquid rocket engines, gas turbines or any other controlled environment for that matter places a huge emphasis on safe and effective operations. These applications make use of relatively small amounts of propellant volumes to generate enormous amounts of energy through combustion for producing thrust. For such cases involving enormous energy interactions, combustion comes with its own set of challenges. The predominant challenge among them all is that of …

In-Flight Wingtip Folding: Inspiration From The Xb-70 Valkyrie, Gaétan X. Dussart, Mudassir Lone, Ciaran O'Rourke, Thomas Wilson

International Journal of Aviation, Aeronautics, and Aerospace

Wingip folding can be used to extend aircraft wingspan, allowing designers to take advantage of reduced induced drag whilst respecting ground operational limitations. Such devices can also be used in-flight for a variety of other benefits including load alleviation and flight control. The majority of in-flight folding research takes inspiration in past developments made on the XB-70 Valkyrie, which used the folding devices for stability and lift performance benefits. In this paper, the authors investigate the capabilities of the folding wingtip system and potential scaling to large civil aircraft. Manufacturing details are used to size the actuators whilst the aerodynamic …

Global Aviation System: Towards Sustainable Development, Marina P. Bonser Dr.

International Journal of Aviation, Aeronautics, and Aerospace

Aviation around the world has integrated into a global system. As the integration process continues, more aspects and levels of it need to be lead towards the sustainable development of the whole system via advancing strategic management, global communication proficiency, and technological expertise. It becomes essential to enrich global language (English) proficiency with cross-cultural communication competence not only for communication in the air but also for airport security, passenger and cargo services, aircraft and equipage engineering, building, and maintenance. Nowadays lower levels of management need more advanced strategic thinking and problem solving skills, and higher levels of management need global …

On Atmospheric Lapse Rates, Nihad E. Daidzic

International Journal of Aviation, Aeronautics, and Aerospace

We have derived and summarized and most important atmospheric temperature lapse rates. ALRs essentially govern vertical atmospheric air stability and creation of some cloud types. The sensitivity analysis of various atmospheric lapse rates and their dependence on actual ideal-gas air properties and gravitational attraction was conducted for the first time to the best of our knowledge. SALR, which has DALR as the upper asymptote, showed steepest decrease at around 9 degrees Celsius then flattening out and apparently approaching another asymptotic solution which has not been investigated as it falls outside of the terrestrial temperature range. ISA lapse rates are adopted …

Design And Realization Of An Unmanned Aerial Rotorcraft Vehicle Using Pressurized Inflatable Structure, Nirmal Sadasivan

International Journal of Aviation, Aeronautics, and Aerospace

Unmanned aerial rotorcraft vehicles have many military, commercial and civil applications. There is a necessity to advance the performance on several ranges of rotorcraft for using these vehicles successfully in the expanded future roles. A lower flight time, noise disturbance and safety issues remain the key obstacles in increasing the efficiency of the rotorcraft for various applications. This work presents the design and realization of a rotorcraft using pressurized inflatable structure filled with lighter than air gas such as helium or hydrogen to provide lift assistance for the vehicle. Two iterative design procedures were developed for designing the vehicle. One …

Comparison Of Flow Field In The Proximity Of A Single Planar & Wrap-Around Fin, Nayhel Sharma, Palak Saini, Hrishabh Chaudhary, Gurteg Nagi, Rakesh Kumar Dr.

International Journal of Aviation, Aeronautics, and Aerospace

Abstract

This paper analyses the results of the computational analysis between a single planar and a wrap-around fin mounted on a semi-cylindrical body. A free-stream Computational Fluid Dynamics (CFD) model was simulated for both cases in the Mach 0.4-3.0M range at 0°Angle of attack, in which, the behavior of flow around the fin was investigated using a turbulence model of higher order discretization. The post-processing shows all the possible views of the flow dynamics around the fins, as well as the missile body. The aerodynamic drag and the rolling moment characteristics of the planar and the wrap-around fin have been …

Determination Of Aerodynamic Forces And Control Requirement During Ground Effect, Ambuj Srivastava

International Journal of Aviation, Aeronautics, and Aerospace

The current work delivers the effect of ground proximity on longitudinal aerodynamic forces and the elevator deflection required for trimming the aircraft. The academic understanding states that the with the increasing proximity to the ground,downwash progressively reduces.The methodology adopts the approximation of linear decrement for the estimation of the residual downwash at any height above ground within the unit wingspan. The proposed method utilizes non-dimensional height above ground for the approximation of effective downwash angle in the presence of ground. The approximately predicted effective downwash angle is subsequently utilized to estimate the effect of ground proximity on longitudinal forces, trim …

Optimization And Analysis Of An Elite Electric Propulsion System, Mehakveer Singh, Kapil Yadav, Satnam Singh, Vikas Chumber, Harikrishna Chavhan

International Journal of Aviation, Aeronautics, and Aerospace

Abstract- Electric propulsion has a promising system to create new possibilities in this technological era as well as control the harmful gaseous emission. This paper put a vision on several parameters of electric propulsion. The engine’s performance is comparable to the current propulsion devices and provides a lightweight solution to the robust technologies’ dependent on chemical energy sources. There are a plethora of factors which is enhanced by electric propulsion such as, overall efficiency, capabilities, and robustness of future air vehicles as well as mainly overcome from exhaust hazards. Electric propulsion systems have the potential of utilizing the electrically-driven propulsion …

A Trust In Air Traffic Controllers (T-Atc) Scale, Bradley S. Baugh, Scott R. Winter

International Journal of Aviation, Aeronautics, and Aerospace

Trust is a concept that cannot be easily measured. Further, trust is domain-specific. Trust is a foundational aspect of safe flight operations in the National Airspace System, and while there has been much attention to trust in teams and trust in automation, there appears to be a gap in knowledge of a pilot’s trust in air traffic controllers. The purpose of this study was to develop and validate the Trust in Air Traffic Controllers (T-ATC) scale, a summative scale to measure a pilot’s trust in air traffic controllers. This study followed a three-step methodology. In steps one and two, words …

Computation Of Eclipse Time For Low-Earth Orbiting Small Satellites, Sumanth R M

International Journal of Aviation, Aeronautics, and Aerospace

This paper addresses a method for computing eclipse and daylight time for satellites in LEO. Continuous health-monitoring of the satellite is required for the success the mission. For this, the satellites are primarily powered by solar energy but during the eclipse time, the satellite’s functioning is affected as it cannot generate power during this period and also, its temperature drops rapidly. To tackle these issues, computing eclipse time for satellites becomes essential so as to plan for sizing its secondary power source for continuous functioning. In this work, eclipse time is being computed and it is shown that eclipse time …

3d Textile Preforms And Composites For Aircraft Strcutures: A Review, Abbasali Saboktakin

International Journal of Aviation, Aeronautics, and Aerospace

Over the last decades, the development of 3D textile composites has been driven the structures developed to overcome disadvantages of 2D laminates such as the needs of reducing fabrication cost, increasing through-thickness mechanical properties, and improving impact damage tolerance. 3D woven, stitched, knitted and braided preforms have been used as composites reinforcement for these types of composites. In this paper, advantages and disadvantages of each of them have been comprehensively discussed. The fabric architects and their specification in particular stitched preforms and their deformation mode for aerospace applications have been reviewed. Exact insight into various types of damage in textile …

Low Level Turbulence Detection For Airports, Anthony O' Connor, Derek Kearney

International Journal of Aviation, Aeronautics, and Aerospace

Abstract—— Low level wind shear and turbulence present a serious safety risk to aircraft during the approach, landing and take-off phases. Despite many advances in on-board and ground based warning systems. Wind shear remains a formidable force that coupled with a microburst can overpower any aircraft. Aviation reports have concluded that pilots need to have improved information in relation to tailwinds, wind shear and wind variations on approach and during the landing phases. Low level wind shear continues to cause disruption, delays and contribute to aircraft crashes. As recently as 2016, two Boeing aircraft crashed while attempting a Go-around …

Strategies In Developing An Aviation & Aerospace Skill Ecosystem For The State Of Telangana, India – Case Study Of Task -Telangana Academy For Skill And Knowledge, Kim Chua, Sujiv Nair, M.P Ganesh Dr.

International Journal of Aviation, Aeronautics, and Aerospace

The aviation & aerospace sector in India has been expanding and growing through partnerships and new research facilities, thereby encouraging more players to invest and optimize the manufacturing process. Improving green and fuel-efficient technologies have contributed to a steady rise in fuelling the demand for aerospace engineers.

The state of Telangana is fast emerging as a new aviation cluster with some of the country’s best-qualified engineers and technicians. The potential of the aerospace industry is immense as it continuously requires skilled technicians and engineers. Considering the precision of skill required, it is imperative that rigorous training be imparted to all …

Computational Study Of Flow Interactions Over A Close Coupled Canard-Wing On Fighter, Setyawan Bekti Wibowo, Sutrisno Sutrisno, Tri Agung Rohmat

International Journal of Aviation, Aeronautics, and Aerospace

There have been many attempts to improve the flying performance of a fighter. By modifying the flow that occurs along the fuselage is expected to improve the performance of the aircraft. One of the indicators of combat aircraft performance is the ability to perform maneuver movement. Adding a canard as forewing on the fighter wing configuration is considered capable of raising the ability in maneuver movement. The use of canard-delta pairs will affect the performance and aerodynamic characteristics of the plane. Wings and canards with delta configuration will make the rolled-up vortex as a lifting force producer on the aircraft. …

Mro Cybersecurity Swot, Danita Baghdasarin

International Journal of Aviation, Aeronautics, and Aerospace

This article intended to identify gaps in the safety management system (SMS) framework when it comes to dealing with cyber risks and hazards in the maintenance, repair, and overhaul (MRO) industry. Cybersecurity is currently a concern of the aviation industry, but organizations in the MRO industry do not seem to be aware of any specific risks and hazards and therefore are not prepared to handle them. Concerns are largely around the increasing reach of aviation and the digital transformation of infrastructure, but the body of knowledge does not go into any greater detail. As a result, it is hard to …