Engineering Commons^™

The Design And Fabrication Of A Microfluidic Reactor For Synthesis Of Cadmium Selenide Quantum Dots Using Silicon And Glass Substrates, Peter Robert Gonsalves

Master's Theses

A microfluidic reactor for synthesizing cadmium selenide (CdSe) quantum dots (QDs) was synthesized out of a silicon wafer and Pyrex glass. Microfabrication techniques were used to etch channels into the silicon wafer. Holes were wet-drilled into the Pyrex glass using a diamond-tip drill bit. The Pyrex wafer was anodically bonded to the etched silicon wafer to enclose the microfluidic reactor. Conditions for anodic bonding were created by exposing the stacked substrates to 300V at ~350oC under 5.46N of force. A syringe containing a room temperature CdSe solution was interfaced to the microfluidic reactor by using Poly (dimethylsiloxane) (PDMS) as an …

Design And Analysis Of A Reusable N2o-Cooled Aerospike Nozzle For Labscale Hybrid Rocket Motor Testing, Daniel Joseph Grieb

Master's Theses

A reusable oxidizer-cooled annular aerospike nozzle was designed for testing on a labscale PMMA-N₂0[1] hybrid rocket motor at Cal Poly-SLO.[2] The detailed design was based on the results of previous research involving cold-flow testing of annular aerospike nozzles and hot-flow testing of oxidizer-cooled converging-diverging nozzles. In the design, nitrous oxide is routed to the aerospike through a tube that runs up the middle of the combustion chamber. The solid fuel is arranged in an annular configuration, with a solid cylinder of fuel in the center of the combustion chamber and a hollow cylinder of fuel lining …

Polar Field Oriented Control With 3rd Harmonic Injection, Martin Todd Hess

Master's Theses

Abstract

POLAR FIELD-ORIENTED CONTROL

with

3^RD HARMONIC INJECTION

Martin Todd Hess

Field Oriented Control (FOC), also known as vector control, is a widely used and well documented method for controlling Permanent-Magnet Synchronous Motors (PMSM) and induction motors. Almost invariably the orientation of the stator and rotor (field) fluxes are described in rectangular coordinates. In this thesis we explore the practicality of using polar coordinates.

Third harmonic injection is also a well-known technique that allows full utilization of the bus (DC-link), thus allowing the motor to run to full base speed without the use of field weakening. This technique potentially …

Pico-Satellite Integrated System Level Test Program, Marcus A. Ruddy

Master's Theses

Testing is an integral part of a satellite’s development, requirements verification and risk mitigation efforts. A robust test program serves to verify construction, integration and assembly workmanship, ensures component, subsystem and system level functionality and reduces risk of mission or capability loss on orbit.

The objective of this thesis was to develop a detailed test program for pico-satellites with a focus on the Cal Poly CubeSat architecture. The test program established a testing baseline from which other programs or users could tailor to meet their needs. Inclusive of the test program was a detailed decomposition of discrete and derived test …

Experimental Investigation Of Suction Slot Geometry On A Goldschmied Propulsor, Nicole M. Thomason

Master's Theses

The Goldschmied Propulsor concept combines boundary layer suction and boundary layer ingestion to improve propulsive efficiency and reduce drag on an axisymmetric body. This investigation of a Goldschmied Propulsor aimed to determine influential characteristics of the suction slot geometry to aid in better slot geometry design and to decrease the suction flow requirements for maintaining attached flow over the entire model surface. The Propulsor model was 38.5 inches in length with a max diameter of 13.5 inches. Three suction slot geometries were investigated with the addition of aluminum cusps to the slot entrance. The cusps varied in the distance they …

Dynamic Model Creation And Scripting Support In The Horizon Simulation Framework, Brian Jeffrey Butler

Master's Theses

Dynamic model creation and support for the Lua scripting language was added to the Horizon Simulation Framework used for the verification and validation of system-level requirements. The addition of scripting support allows for subsystem models and their algorithms to be defined using a simpler scripting language, rather than C++. The Luabind library by Rasterbind software is used to expose the C++ algorithms and classes to Lua that are already defined in the framework. Interoperability between Lua and C++ code allows for the ease of use of a scripting language while utilizing the utility classes and functions already created. The dynamic …

Design And Experimental Validation Of Continuous Dna Separation Using Itp-Based Microfluidic Device, Nora C. M. Goscinski, Mary E. Rosa, Elizabeth K. Wheeler, Maxim Shusteff

Chemistry and Biochemistry

We have demonstrated a chip-based microfluidic device suitable for rapid and high-throughput DNA separation and purification for downstream analysis. The glass-based device incorporates a transverse free-flow isotachophoresis (tFF-ITP) that overcomes the volume limitations of CE approaches, and allows continuous sample processing in contrast to batch-mode solid-phase extraction (SPE). The device is able to focus DNA at flow rates up to 100 uL/min, and sample conductivity up to 2 mS/cm. Downstream of the chip, 30-40% of DNA from the input sample is recovered as a result of ITP focusing, and preliminary results indicate that this design is able to purify DNA …

Characterization Of Mixing In A T-Style Microfluidic Chip, Brian Eric Harley

Master's Theses

The goal of this study is to characterize the mixing that occurs in a microfluidic chip. To characterize the mixing, the minimum length to complete mixing and evolution of mixing will be investigated. There are two types of mixing that occur within a microfluidic channel, diffusion and advection. In the beginning of the microfluidic chip, diffusion is the dominant form of mixing, and in the later portion of the microfluidic chip advection is the dominant form of mixing. The type of design used for this experiment was a zig zag geometry microfluidic chip with channel dimensions of 60 µm X …

A Novel In-House Design Of A Bioreactor For The Modeling Of An In Vitro Blood Brain Barrier Model, Ian Mahaffey

Biomedical Engineering

The blood brain barrier is the protector of the central nervous system and a physical barrier that functions to regulate the substances that can pass in and out of the brain; it is the function and integrity of this system that keeps the homeostasis of the central nervous system. Yet this shield against foreign invaders in the blood also prevents drugs designed for treatment of various ailments of the central nervous system from reaching their target in the brain. Developing drugs that can pass through this barrier, and understanding it’s function has become an area of increasing interest. Many researchers …

Design And Production Aspects Of An Electroluminescent Segment Display, Veronica Kopp, Chris Nixon

Graphic Communication

The purpose of this study was to get a better understanding of the different ways printed circuits could be constructed and then implemented into creative, visual designs for printed electroluminescent displays. A variety of circuit design variables, such as area and length, were tested that will help create solutions for printed electronics.

This study tested different variables of circuit design, such as length of silver traces and the size of the image area, to help optimize ways to build a printed circuit. Then, findings were implemented into a segmented graphic display in order to analyze innovative ways to utilize multiple …

Optical Mode Pattern Study Of Gan Based Leds With And Without Nanoscale Top Grating, Gregory Chavoor

Electrical Engineering

This study analyzes optical confinement factor and light emitting mode order for three different GaN LEDs: a conventional LED, thin Film LED, and thin Film LED with a photonic crystal (PhC) grating. For the first structure, we increase the thickness of Al_xGa_1-xN from 0 to 600nm, alter the x composition in Al_xGa_1-xN from 0.05 to 0.2 in steps of 0.05, and adjust the p-GaN and n-GaN thicknesses each from 0 to 200nm. For the second structure, we alter the n-GaN substrate thickness from 300-1000nm in steps of 100nm and 1000-4000nm in steps …

Equating A Car Alternator With The Generated Voltage Equation, Ervin Carrillo

Electrical Engineering

No abstract provided.

White Light Led Load System, Ronald Lu, Benjamin Ng

Electrical Engineering

No abstract provided.

Compressed Air Foam Fire Grounds Evolution Tests, Justin A. Lapolla, Alexander L. Morano, Vincent P. Luchsinger

Mechanical Engineering

Compressed air foam firefighting technology has been purchased by a number of urban fire departments in the United States. These departments have curtailed their use of these systems until potential safety hazards associated with the use of compressed air foam systems in interior structure fires are evaluated. This project is part of a greater effort to evaluate the efficacy and practicality of compressed air foam systems for use in structural firefighting. This project focused on developing test apparatuses and test methods for measuring the following safety-related parameters: 1.) nozzle reaction force of a fire nozzle, 2.) the force required to …