Engineering Commons^™

Retrofit Of Corroded Corrugated Metal Culverts Using Gfrp Slip-Liner, Rahulreddy Chennareddy

Civil Engineering ETDs

Culverts are water conveyance structures, typically used to allow water flow and maintain a balance between the flow streams without interrupting structures such as highways and bridges. Corrugated metal pipes (CMPs) have been used as culverts in North America since the 1950s because of their low cost and simple construction method. Today, the corrosion of CMPs is a major problem faced by all U.S. Departments of Transportation. There is an urgent need to provide an efficient solution, one that is corrosion-resistant, to retrofit thousands of corroded CMPs across the country. High specific strength, high strength to weight ratio, corrosion resistance, …

Effect Of Incorporating Pottery And Bottom Ash As Partial Replacement Of Cement, Bassam A. Tayeh, Doha M. Alsaffar, Lawend K. Askar, Asmahan Issa Jubeh

Karbala International Journal of Modern Science

This study addressed the environmental constraints in cement produc­tion. Ordinary Portland cement (OPC) was replaced with pottery powder (PP, produced by grinding locally available pottery) and bottom ash (BA) at 10%, 20% and 30% of cement mass. Moreover, 4% calcium chloride solution (CaCl₂.2H₂O) was used as mixing water. Material properties, such as standard consistency, setting time and compressive strength, were measured with different percentages of OPC replacement with PP and BA. Results indicated that the replacement with PP and BA increased the water demand to achieve the standard consistency. These results revealed that the strength evolution …

Mandela Splash Pad Pre-Construction Plan, Levi Sandbulte

Theses/Capstones/Creative Projects

In the construction industry, it is the responsibility of the general contractor to take the architect’s ideas and turn it into a real building. Many times this requires ample communication and several drafts. This efficient execution of this process is vital to the completion of a successful project. In this project, I practice this communication process. The challenge presented by the owner is to build an affordable splash pad, and without impacting the construction schedule of the Early Childhood Development Center (ECDC) that is being built on the same property at the same time. This proposal gives the owner a …

Ultrasonic Wave Propagation In Copper/Graphene Metal Matrix Composites, Casey Lindbloom

Mechanical Engineering Undergraduate Honors Theses

Emerging metallic composite materials implanted with graphene sheets are showing immense promise, with benefits being observed with regards to mechanical, thermal, and electrical material properties. This research aims to investigate the effects on ultrasonic wave propagation in Copper/Graphene Metal Matrix Composites (Cu/Gr MMCs) with varying graphene arrangements inspired from nacre and bone nanoscale material distributions. To accomplish this, the molecular dynamics (MD) method is utilized to simulate nanoscale wave propagation on a set of Cu/Gr MMCs with differing graphene arrangements and volume percentages ranging up to 4.56%. The computational model results are then analyzed to determine the variation in energy …

Damage Resistance And Tolerance Of 3d Woven Composites, Justin T. Mcdermott

Electronic Theses and Dissertations

Composite materials have been adopted into primary aircraft structures by virtue of their great strength-to-weight and stiffness-to-weight ratios, fatigue insensitivity, and corrosion resistance. These characteristics are leveraged by aircraft designers to deliver improved fuel effciency and reduced scheduled maintenance burdens for their customers. These benefits have been impressively realized in the Boeing 787 and Airbus A350 XWB, with airframes utilizing about 50% composites by weight. Tempering these successes, however, are the inherent vulnerabilities of carbon-fiber reinforced composites. When compared to conventional metallic structure, composite laminates are more sensitive to stress concentrations at mechanical fastenings and damage due to low-velocity impact. …

Development Of A Mix Design Adjustment Method For Fiber Reinforced Concrete And Super High Performance Concrete Based On Excess Paste, Joe Malloy

Department of Civil and Environmental Engineering: Dissertations, Theses, and Student Research

The main objective of this study was to develop a mix design adjustment method for Fiber Reinforced Concrete (FRC) that would maintain appropriate workability while improving hardened concrete performance. A literature review was conducted to examine existing methods for adjusting mix designs to account for fiber introduction. It was found that while increasing fine aggregate and cement paste content can make up for lost workability with the addition of fibers, no rational mix design adjustment method is available. Reference mix designs from the Nevada Department of Transportation and the Nebraska Department of Transportation were used, and this study focused on …

Additively Manufactured Continuous Carbon Fiber Thermoplastic Composites For High-Performance Applications, Nekoda Van De Werken

Mechanical Engineering ETDs

The goal of this dissertation is to provide a foundation for the advancement of additive manufacturing (AM) toward production of high-performance carbon fiber reinforced polymer matrix composites (CFRPs). AM can provide valuable advantages over conventional composite manufacturing techniques, including the control over fiber orientation, capability of manufacturing complex geometries, out-of-autoclave processing, elimination of the need for composite tooling, and the ability to perform lights-out manufacturing. Currently, however, a suite of challenges related to modelling, design, manufacturing defects, and general limitations in the current understanding of the processing-structure-property relationships exist in AM of composites. To this end, this dissertation investigates novel …

The Application Of Gray-Scale Level-Set Method In Segmentation Of Concrete Deck Delamination Using Infrared Images, Chongsheng Cheng, Zhigang Shen

Department of Construction Engineering and Management: Faculty Publications

Conventional nondestructive delamination detection of concrete pavements through thermography is often based on temperature contrasts between delaminated and sound areas. Non-uniform backgrounds caused by the environmental conditions are often challenging for contrast-based methods to robustly differentiate the delaminated areas from the sound areas. Instead of focusing on the temperature contrast, this study proposes a temperature gradient-based level set method (LSM) to detect boundaries for delamination segmentations. A modified edge indicator function is developed to represent the normalized temperature gradient of a thermal image. The experimental study was conducted to evaluate its applicability and stability for boundary detection in terms of …

Mechanical Behavior Of Ternary Metallic Glasses And Their Composites, Xue Liang

FIU Electronic Theses and Dissertations

The vast demands for advanced materials have been putting tremendous pressure on materials scientists and engineers to discover and produce novel lighter and stiffer materials. This dissertation is devoted to the development and fundamental understanding of the strength and the structures within Aluminum ternary metallic glasses (MGs) and their composites, which have a low density and promising high strength. The dissertation focuses on the following content: The multi-objective optimization algorithm predicted the Al_16.5Ni₈Ce_75.5 ternary metallic glass composition with an improved glass-forming ability (supercooled liquid region ∆����=29K), based on the provided dataset. Inoue Criteria can predict …

Micro-Mechanical Analysis Of Corrosion Products Formed During Long-Term Carbonation Induced Corrosion Of Steel, Marijana Serdar, Dubravka Bjegovic, Valérie L’Hostis, Stéphane Poyet, Damien Féron

International Conference on Durability of Concrete Structures

During corrosion distinct types of corrosion products form, composed of different ratios of ferrous ions and oxide, hydroxides. Corrosion products have different physical and mechanical properties, mainly density, resistivity, volume and modulus of elasticity compared to iron. Knowing properties of corrosion products is indispensable for service life modelling of structures and can give valuable insight into the long-term corrosion propagation process. In this study micro-indentation method was used to evaluate mechanical properties of different layers formed during long-term carbonation induced corrosion of steel in concrete. Investigation was performed on three sets of reinforced concrete samples, that underwent corrosion during 50, …

Development Of Engineered Cementitious Composites With Conductive Inclusions For Use In Self-Sensing Applications, Benny Suryanto Dr, Danah Saraireh Ms, Steven Walls Mr, Jaehwan Kim Dr, W John Mccarter Prof

International Conference on Durability of Concrete Structures

The mechanical and a.c. electrical properties of a new varietal of engineered cementitious composite (ECC) incorporating conductive inclusions are presented. Electrical measurements were undertaken over a wide frequency range while curing and when under uniaxial tensile loading to study the influence of ongoing hydration and multiple microcrack formation on the composite electrical impedance. When presented in Nyquist format, the work shows that conductive inclusions reduce the bulk resistance of the composite while enhancing its polarizability, transforming the classic, single-arc bulk response of typical cement-based materials to a two-arc response. The bulk resistance was shown to increase with time and damage, …

Why The Crackling Deformations Of Single Crystals, Metallic Glasses, Rock, Granular Materials, And The Earth’S Crust Are So Surprisingly Similar, Karin A. Dahmen, Jonathan T. Uhl, Wendelin J. Wright

Faculty Journal Articles

Recent experiments show that the deformation properties of a wide range of solid materials are surprisingly similar. When slowly pushed, they deform via intermittent slips, similar to earthquakes. The statistics of these slips agree across vastly different structures and scales. A simple analytical model explains why this is the case. The model also predicts which statistical quantities are independent of the microscopic details (i.e., they are "universal"), and which ones are not. The model provides physical intuition for the deformation mechanism and new ways to organize experimental data. It also shows how to transfer results from one scale to another. …

Experimental And Numerical Investigation On The Irregularity Of Carbonation Depth Of Concrete Under Supercritical Condition, Hao Bao Masc, Min Yu Dr., Jianqiao Ye Dr., Lihua Xu Dr., Yin Chi Dr., J Ye

International Conference on Durability of Concrete Structures

The heterogeneity of a cement-based material results in a random spatial distribution of carbonation depth, which may significantly affect the mechanical properties and durability of the material. Currently, there is a lack of both experimental and numerical investigations aiming at a statistical understanding of this important phenomenon. This paper presents both experimental and numerical supercritical carbonation test results of concrete blocks. The random fields of porosity and two-dimension random aggregate model of concrete were proposed for the simulation. The carbonation depths are measured and distributed along the carbonation boundary by the proposed rapid image processing technique, which are then statistically …

Guiding Principles In Developing The South African Approach To Durability Index Testing Of Concrete, Yunus Ballim, Mark Alexander

International Conference on Durability of Concrete Structures

Focused thinking on the possibility of early-age testing of concrete for long-term durability started in earnest during the late 1980’s in South Africa. Through sustained research, development and trial implementation on construction projects, three durability index (DI) tests have emerged, two of which have been adopted as national standard test methods for concrete construction, the remaining one being prepared a national standard. In this paper we review the guiding or foundational principles that directed the development of these DI tests, with a view to assessing the appropriateness and relevance of these guiding principles to modern concretes. The last 30 years …

The Influence Of Waste Glass Powder On The Chloride Binding Capacity Of Fly Ash/Cement Hardened Paste, Jh Yan, Tingyu Hao

International Conference on Durability of Concrete Structures

The potential of using waste glass powder to increase the chloride binding capacity of fly ash/cement hardened paste was investigated. When only fly ash replacing cement, the chloride binding capacity was raised within 28d when the fly ash replacement level was in the range from 30-50% by mass. But at a longer age of 60 to 90d, the binding performance was increased at the replacement level of 10-30wt%. The chloride binding capacity of glass powder-fly ash-cement system was increased by adding glass powder of 2% and 4% by mass at 7d while those at larger addition and longer age reduced. …

From Critical Behavior To Catastrophic Runaways: Comparing Sheared Granular Materials With Bulk Metallic Glasses, Alan A. Long, Dmitry Denisov, Peter Schall, Todd C. Hufnagel, Xiaojun Gu, Wendelin J. Wright, Karin A. Dahmen

Faculty Journal Articles

The flow of granular materials and metallic glasses is governed by strongly correlated, avalanche-like deformation. Recent comparisons focused on the scaling regimes of the small avalanches, where strong similarities were found in the two systems. Here, we investigate the regime of large avalanches by computing the temporal profile or “shape” of each one, i.e., the time derivative of the stress-time series during each avalanche. We then compare the experimental statistics and dynamics of these shapes in granular media and bulk metallic glasses. We complement the experiments with a mean-field model that predicts a critical size beyond which avalanches turn into …

Contamination Of Coupling Glass And Performance Evaluation Of Protective System In Vacuum Laser Beam Welding, Yongki Lee, Jason Cheon, Byung-Kwon Min, Cheolhee Kim

Mechanical and Materials Engineering Faculty Publications and Presentations

Vacuum laser beam welding enables deeper penetration depth and welding stability than atmospheric pressure laser welding. However, contaminated coupling glass caused by welding fumes in the vacuum space reduces laser transmittance, leading to inconsistent penetration depth. Therefore, a well-designed protective system is indispensable. Before designing the protective system, the contamination phenomenon was quantified and represented by a contamination index, based on the coupling glass transmittance. The contamination index and penetration depth behavior were determined to be inversely proportional. A cylindrical protective system with a shielding gas supply was proposed and tested. The shielding gas jet provides pressure-driven contaminant suppression and …

Effect Of Ion Implantation On The Mechanical Properties Of The Grain And Grain Boundary Regions Of Inconel X750, Maisaa Nezar Tawfeeq

Electronic Thesis and Dissertation Repository

Annulus gas spacers in CANada Deuterium Uranium (CANDU) nuclear reactors are made from the heat-treated Inconel X750 Nickel-based alloy. This alloy is designed to have high strength and creep resistance at elevated temperature. Unlike other reactor designs, the CANDU reactor has a high thermal neutron fluence, which results in an enhancement of the radiation damage and the internal production of helium and hydrogen. They are thus susceptible to microstructural instability and mechanical property degradation with time. Studies of ex-service spacers have indicated that they display intergranular embrittlement and lower ultimate tensile strength compared to nonirradiated Inconel X750. The primary degradation …

Vanadium-Based Nanomaterials For Improved Zn Ion Storage, Jianwei Lai

LSU Master's Theses

Rechargeable aqueous zinc-ion batteries (ZIBs) have been intensively studied as novel promising large-scale energy storage systems recently, owing to their advantages of high abundance, cost effectiveness, and high safety. However, the development of suitable cathode materials with superior performance are severely hampered by the sluggish kinetics of Zn²⁺ with divalent charge in the host structure.

Our Work demonstrates boosting the electrochemical performances of nanostructured cathode materials for aqueous ZIBs. The first project is focused on the interlayer-expanded V₆O₁₃∙nH₂O nanosheets as promising cathodes. Benefiting from the synthetic merits of its favorable architecture and expanded …

Graphene Foam Reinforced Shape Memory Polymer Epoxy Composites, Adeyinka Idowu

FIU Electronic Theses and Dissertations

Shape memory polymer (SMP) epoxy has received growing interest due to its facile processing, low density, and high recoverable strain. Despite these positive attributes, SMP epoxy has drawbacks such as slow recovery rate, and inferior mechanical properties. The slow recovery rate restricts the use of SMP epoxy as a functional structure.

The aim of the present work is to explore the capabilities of three-dimensional (3D) graphene foam (GrF) and graphene nanoplatelet (GNP) as reinforcements in SMP epoxy to overcome their slow recovery and improve the mechanical properties. GrF and GNP based SMP epoxy composites are fabricated by mold-casting approach and …

Reduction Of Structural Damage From The Thermal Expansion Of Concrete Using Multifunctional Materials, Darren Hartl, Mirmilad Mirsayar

Publications

This study leveraged past successes in the analysis and design of shape memory alloy (SMA) components to address the issue of thermal expansion in concrete structures. Since the SMA used in the current work is relatively cheaper than other common SMAs (less than $50/lb compared to NiTi which is $200/lb due to difficulties in processing), it is anticipated that the findings of the study could be implemented in real infrastructures made of concrete, asphalt concrete, and other complex large infrastructure. Low-cost Fe-SMAs and other multifunctional materials can be considered as a replacement for components made of steel (e.g., in reinforced …

Soil-Recycled Aggregate-Geopolymer Road Base/Subbase Mixtures: Steps Towards Sustainability, Mohammad Khattak, Daniel Odion

Publications

This study deals with the development of Soil-Geopolymer mixtures using flyash, alkali activator and recycled aggregates (RAG) including recycled concrete (RCA) and reclaimed asphalt (RAP) as an alternative to soil-cement for pavement base and subbase layers. Several mix constituents were varied such as flyash type and content, RCA and RAP content and ratio of sodium silicate and sodium hydroxide. Experiment design was established and mechanical and durability characteristics of Soil-RAG-Geopolymer mixtures were evaluated and then compared to the conventional soil-cement mixtures. The results of the testing showed that for the selected Soil-RAG-Geopolymer mixtures the strength, stiffness, permanent deformation, and durability …

Force Oscillations Distort Avalanche Shapes, Louis W. Mcfaul, Wendelin J. Wright, Jordan Sickle, Karin A. Dahmen

Faculty Journal Articles

Contradictory scaling behavior in experiments testing the principle of universality may be due to external oscillations. Thus, the effect of damped oscillatory external forces on slip avalanches in slowly deformed solids is simulated using a mean-field model. Akin to a resonance effect, oscillatory driving forces change the dynamics of avalanches with durations close to the oscillation period. This problem can be avoided by tuning mechanical resonance frequencies away from the range of the inverse avalanche durations. The results provide critical guidance for experimental tests for universality and a quantitative understanding of avalanche dynamics under a wide range of driving conditions.

Development Of Geopolymer-Based Cement And Soil Stabilizers For Transportation Infrastructure, Miladin Radovic, Anand Puppala

Publications

Geopolymer Cement (GPC) has drawn much attention in the recent years as an alternative to Ordinary Portland Cement (OPC) for soil stabilization, pavements, bridges and other transportation structures due to their good mechanical properties in comparison to OPC. In addition, GPC can be processed at room temperatures from aqueous solutions of waste materials (e.g. fly ash) or abundant natural sources (e.g. clay), thereby significantly reducing CO2 production associated with processing of OPC. As such, GPC proves to be a more sustainable and environmentally friendly alternative than OPC. This research explores methods to develop GPC with desired properties and evaluate their …

Investigation Of Physical And Dynamic Properties Of High Porous Concrete, Ildar Akhmadullin

Publications

This project pursued two main objectives: (1) providing opportunities to Baton Rouge Community College (BRCC) students to develop hands-on laboratory skills and exposure to the transportation field, and (2) investigating porous concrete properties. Several BRCC student groups performed the work presented within this report; students prepared samples with different porosity and permeability according to standard specifications. The testing of the samples was performed at the Louisiana Transportation Research Center (LTRC) facility under the supervision of LTRC specialists. Findings indicate that the porosity of samples is backward proportional to the compression strength. This function is not linear but can be estimated …

Toward Non-Corrosion And Highly Sustainable Structural Members By Using Ultra-High-Performance Materials For Transportation Infrastructure, Shih-Ho Chao, Ashish Karmacharya

Publications

This research focused on investigating a highly sustainable and efficient reinforced concrete structural member for future infrastructure by utilizing emerging high-performance materials. These materials include ultra-high-performance fiber-reinforced concrete (UHP-FRC) and corrosion-resistant high-strength fiber-reinforced polymer (FRP) bars. Four reduced scale UHP-FRC specimens were tested under large displacement reversals to prove the proposed new ductile-concrete strong-reinforcement (DCSR) design concept by fully utilizing these ultra-high-performance materials. Micro steel fibers were incorporated into three specimens and ultra-high molecular weight polyethylene fibers were blended into the fourth specimen. One specimen with ASTM A1035 MMFX high-strength steel rebars, one with high-strength glass fiber reinforced polymer (GFRP) …

General Nonlinear-Material Elasticity In Classical One-Dimensional Solid Mechanics, Ronald Joseph Giardina Jr

University of New Orleans Theses and Dissertations

We will create a class of generalized ellipses and explore their ability to define a distance on a space and generate continuous, periodic functions. Connections between these continuous, periodic functions and the generalizations of trigonometric functions known in the literature shall be established along with connections between these generalized ellipses and some spectrahedral projections onto the plane, more specifically the well-known multifocal ellipses. The superellipse, or Lam\'{e} curve, will be a special case of the generalized ellipse. Applications of these generalized ellipses shall be explored with regards to some one-dimensional systems of classical mechanics. We will adopt the Ramberg-Osgood relation …

Uhpc Shear Keys In Concrete Bridge Superstructures, Craig Newtson, Brad Weldon, Elsy Flores, Jordan Varbel, William Toledo

Publications

This research investigated the use of locally produced ultra-high performance concrete (UHPC) as a grouting material to repair deteriorated shear keys. Shear keys are used in adjacent girder superstructures to produce monolithic behavior and load transfer across the structure. Shear key durability is a concern since shear key degradation can jeopardize the integrity of the structure. Transportation agencies have reported that 75% of distress in adjacent girder bridges is due to cracking and de-bonding along shear keys. Previous research has shown that locally produced UHPC has excellent mechanical and durability properties. UHPC has also been shown to have good bonding …

Disaster Resilient And Self-Assessing Multifunctional Transportation Structures, Ibrahim Karaman, Darren Hartl

Publications

This research designs and characterizes multifunctional materials, in particular inexpensive shape memory alloys, for transportation structures that possess excellent mechanical properties and self-sensing capabilities for strengthening and health monitoring. The properties are the Fe-SMAs are sensitive to part size in that the grain size of the material, which can be grown to several inches, should exceed the smallest dimension of the part. In the current work, maximum part size of the large dimension Fe-SMA rods were determined through detailed microstructural investigations. Samples were subjected to abnormal grain growth heat treatments and found out that part size be increased up to …

Workforce Development Symposiums For Uhpc, Brad Weldon, Craig Newtson, Grace Mcmurry, Leticia Davila

Publications

Ultra-high performance concrete (UHPC) is a cementitious material with a dense microstructure that contributes to high compressive strengths as well as enhanced durability properties. UHPC also possesses significant post-cracking strength and ductility due to the addition of fibers. These characteristics produce a material that provides advantages over conventional concrete; however, high costs attributed to materials and production, lack of industry familiarity and knowledge, and the absence of standardized design procedures have impeded its widespread use. To help disseminate knowledge on UHPC, two workforce development symposiums on UHPC were held in Las Cruces, New Mexico. The symposiums consisted of presentations and …