Engineering Commons^™

Behavior Of Concrete Mixes Using Recycled Aggregate Confined With Steel Sections, Latifa Sobhi Kassem, Adnan El-Masri, Nour Webhi

BAU Journal - Science and Technology

Recycled Concrete Aggregate (RAC) is a form of recycled concrete that has been studied for green building for the past 50 years. It can be used to create strong structures, such as seismic retrofitting of earthquake-prone structures. Studies have attempted to experimentally study the effect of using recycled aggregate in concrete, but the literature lacks the use of recycled concrete aggregate rapped with steel rings. This study examines the behavior of circular concrete columns with different percentages of recycled aggregate. It examines the behavior of a column with different percentages of recycled aggregate, one without jacketing, one with partial jacketing, …

Isolation And Characterization Of Caffeine-Degrading Bacteria From Coffee Plantation Areas In Malaysia, Elvina Clarie Dullah, Mohd Fazli Farida Asras

Makara Journal of Technology

Decaffeination by microbial degradation is currently the most optimal and low-cost approach, involving only microbial cells and/or their enzymes. The bacterium was characterized using a series of biochemical tests. Positive results were obtained from carbohydrate fermentation, citrate utilization, and catalase tests, while negative results were obtained from Voges-Proskauer (VP) and indole tests. Three different caffeine concentrations of 0.25%, 0.4%, and 2% were tested and measured through Gas Chromatography-Mass Spectrophotometry (GC-MS) analysis. The highest caffeine reduction (89.25%) was found when 0.25% caffeine was used in the media. Only a small amount of caffeine was reduced to 0.4% and 2%, with 34.78% …

Effect Of Lime Content, Curing Temperature, And Aging Condition On Low-Alkaline Concrete, Mahdi Parsa Pour, Reza Shaban Sharghi, Faezeh Nejati, Elmira Khaksar Najafi

Makara Journal of Technology

This study determines how curing temperatures, aging condition, and hydrated lime contents affect the unconfined compressive strength (UCS), modulus of elasticity, and workability of low-alkaline concrete. Samples were prepared in two different groups to determine the optimum hydrated lime content and aging conditions to assess the mutual effect of NaOH molarity and curing temperature, that is, 70 °C for 48 h or room temperature, on samples with and without lime. The results showed that the increase in hydrated lime content affected alkali concentration. The samples with lime exhibited a clear peak in UCS (6 M NaOH) compared with the continuous …

Optimization Of The Building Envelope And Roof Shading To Reduce The Energy Consumption Of College Low-Rise Buildings In Indonesia, Nasruddin Nasruddin, Azimil Gani Alam, Mohammad Imroz Sohel

Makara Journal of Technology

Energy consumption in buildings is a crucial concern globally, prompting researchers to explore innovative solutions to mitigate its impact. This study investigates the optimization of building envelopes and roof shading systems of existing buildings in Indonesia to realize notable energy savings. Multiple scenarios were explored, with modifications to building envelopes and roof shading, highlighting the overall thermal transfer value as a key parameter. Using EnergyPlus simulations, the efficacy of natural ventilation in corridors and roof shading modifications was assessed in reducing energy consumption. The findings revealed that renovating existing buildings by optimization of the building envelope and roof shading by …

Early-Age Strength And Failure Characteristics Of 3d Printable Polymer Concrete: Numerical Modelling And Experimental Testing, Mohammad Amin Dehghani Najvani

Civil Engineering ETDs

The time-dependent rheological and early-age strength parameters of Polymer concrete (PC) were investigated. PC flow decreased, and the static yield stress and thixotropy increased as the specimen aged, while the dynamic yield stress remained unchanged. The study found that the Herschel-Bulkley model can accurately describe the PC’s rheological behavior over time. The change in cohesion strength and internal friction angle over time was observed using uniaxial unconfined compression and direct shear tests of fresh PC. A time-dependent MohrCoulomb failure criterion was established. Temperature analysis was used to determine the gel time and explain the evolution of the time-dependent early-age strength …

Analysis Of Loading Rate, Fiber Orientation And Material Composition Through Image Processing And Digital Volume Correlation In High Performance Concrete, Aidan R. Carlson

Electronic Theses and Dissertations

Ultra High Performance Concrete (UHPC) and High Performance concrete (HPC) is characterized by high compressive strength and high toughness. This is achieved through maximizing the particle packing density in the matrix and the use of fibers to reinforce the matrix, increasing the materials toughness. The interactions of fibers and the matrix during loading is quite complex and involves several different energy dissipation mechanisms. The goal of this work and this thesis is to investigate these interactions and identify any changes in material response, and hope that these changes may be useful for the design of UHPC moving forward.

In this …

Metal Organic Framework Modifications Of Structural Fibers, Marwan Al-Haik

Publications

A reinforced carbon composite can include a carbon sub­strate and a metal organic framework bonded to the carbon substrate. For example, a reinforced carbon composite can include a first layer, a second layer, and a resin adhered to the first layer and the second layer. The first layer can include a carbon substrate and a metal organic framework bonded to the carbon substrate. The second layer can include a carbon substrate and a metal organic framework bonded to the carbon substrate.

Climate Change Impact On Bridge Scour Risk In Ny State: A Gis-Based Risk Analysis Model, Muhammad Hassan Butt

Publications and Research

Bridge scour, the primary cause of bridge failure in the United States, escalates post-severe storms, necessitating effective mitigation. This study employs a GIS-based risk analysis model to assess climate change's impact on bridge scour and associated risks in New York State. Data from the National Bridge Inventory, climate hazard maps, and geospatial data are integrated.

Barriers To Use Of Cross-Laminated Timber In Maine, Shane R. O'Neill

Forest Resources Faculty Scholarship

To increase understanding of both the adoption rate and in-state manufacturing of mass timber In Maine, the 131^st Legislature and Governor Mills passed LD 881, a resolve directing a study of the barriers facing cross-laminated timber In Maine and provide recommendations to promote their use in construction. This study was developed in response to the resolve. The study engaged 108 unique participants to define available training, education, and experiences across the stakeholders throughout the building lifecycle process in the state.

From this information, the following five recommendations are proposed:

1. Understand the policies and initiatives of other states to develop …

Functional Cementitious Composites With Micro-Sized Particulate Fillers For Additive Construction And Energy-Efficient Buildings, Adam Brooks

Doctoral Dissertations

With a growing energy demand, the development of sustainable and energy efficient building materials is growing rapidly. Numerous researches have focused on low carbon footprint construction materials, high-performance thermal insulations, high-performance façade, and thermal energy storage. Among these, the development of functional cementitious composites has attracted significant attention due to its potential utilities in building energy reduction and decarbonatization efforts. For example, fly ash cenospheres have been used as micro-size lightweight fillers to achieve low density and thermal conductivity. The use of phase change materials (PCM) in concrete has been studied to answer energy demands. While their inclusion into concrete …

Self-Consolidating Concrete Design For Drilled Shaft Structural Applications, Grady S. Caton

Graduate Theses and Dissertations

Self-consolidating concrete (SCC) is a relatively new concrete technology which allows the concrete to be placed without the need for manual or machine vibration. This innovation reduces labor costs, construction times, and can provide a smooth, finished surface. However, this technology is used in the United States primarily in the precast and prestressed concrete industry. The utility of SCC in structural applications, such as areas of dense reinforcement or locations where complex geometry makes consolidation impossible, is also advantageous. In this study, a series of SCC mixtures were developed both with and without fly ash replacement. These mixtures were then …

Comparing In-Situ Liquefaction Triggering Procedures For Sites In Arkansas, Sagar Barua

Graduate Theses and Dissertations

There currently exists a significant amount of uncertainty when designing piles for bridge foundations in liquefiable soil. Currently ARDOT engineers use a Standard Penetration Test (SPT) based liquefaction spreadsheet developed 10 years ago to evaluate liquefaction triggering. Since this spreadsheet was developed, updates to the liquefaction triggering procedures have been published making the spreadsheet out-of-date. Moreover, additional methods of liquefaction evaluation using cone penetration test (CPT) and shear wave velocity (Vs) provide added means of evaluating liquefaction potential. This thesis updates ARDOT's liquefaction triggering evaluation methodology with the newest procedures and incorporates additional empirical liquefaction hazard estimates such as the …

Modular Composite Sandwich Structures For Thermal And Structural Retrofitting Of Existing Buildings, Marc Al Ghazal

Masters Theses

Around 40% of global energy consumption and 30% of worldwide carbon dioxide (CO2) emissions are attributed to buildings. Most of this consumption is dedicated to ensuring thermal comfort. The goal of this research was to develop and field validate retrofit solutions to improve the energy efficiency of buildings. Exterior cladding panels were designed and tested to ensure adequate thermal and structural performance. Sandwich panels (glass fibers reinforced polymer (GFRP) skins and polymeric foam cores) were fabricated using the vacuum assisted resin transfer molding (VARTM) process. Extruded polystyrene (XPS) and polyurethane (PU) foams were compared as core materials through a series …

Bridge Deck Overhang Design: Effective Vehicle Impact Loads, Ultimate Strength, And Implications On Bridge Rail Performance, Andrew Eric Loken

Department of Civil and Environmental Engineering: Dissertations, Theses, and Student Research

When an errant vehicle strikes a bridge railing on a typical girder bridge, impact loads are transmitted downward through the railing and inward through the deck overhang to the primary superstructure elements. In this research effort, design demands for deck overhangs supporting concrete railings were characterized using physical testing and complementary modeling in LS-DYNA. Physical test and modeling results were also used to better characterize the ultimate strength of overhangs supporting post-and-beam railings. Ultimately, a novel design methodology for deck overhangs was developed and proposed for adoption to the AASHTO LRFD Bridge Design Specifications (BDS).

For overhangs with solid concrete …

Improvement Of Rotation Capacity Of Composite Beam-To-Hss Column Connections Using External Horizontal Stiffeners, Mahdi Afshar Arjmand

Master's Theses

Improvement of Rotation Capacity of Composite Beam-to-HSS Column Connections Using External Horizontal Stiffeners

Mahdi Afshar Arjmand

This thesis focuses on the analysis of out-of-plane deformation (OOP) in column flange located in the panel zone of composite beam-to-column steel connection, as a critical aspect of steel structural engineering. This type of connection is an integral component of steel structures, and understanding their behavior is essential for ensuring safety and performance. The investigation involves examining the causes, factors influencing, and potential mitigation strategies for out-of-plane deformation of HSS flange column in these connections. Beam-to-column connections play a vital role in transferring loads …

Effect Of Latex Modified Concrete Overlays With Reduced Surface Preparation On The Load Distribution And Flexural Strength Of Channel Girders, Samuel Dodd

All Theses

This thesis investigates the use of a Latex Modified Concrete (LMC) overlay to increase the strength of prestressed channel girders and enhance their ability to distribute load. The research conducted in this thesis involved material testing of several different LMC mixes and flexural testing of an LMC overlay and girder system. The material testing was used to determine a reasonable LMC mix design and surface preparation method to be used for the overlay. Based on material testing it was concluded that a rapid-set mix and pressure washing of the girder surfaces were a reasonable mix design and surface preparation for …

International Information Management And Bim Best Practice Report, Ted Mckenna, Davitt Lamon

Reports

In order to inform the Digital Leadership and Cultural Change pillar of the Build Digital, a study of international best practice in digital adoption within the built environment sector globally was undertaken and is presented here-in. In order to identify key learnings for Ireland in the context of digital transformation, eight countries were included in this study, namely, Denmark, Finland, Netherlands, Germany, United Kingdom (UK), New Zealand, Australia and Singapore. These countries were selected for various reasons, including the level of digital maturity, the scale of the built environment sector and geographic spread. Key data for each country is included …

Sustainability And Circular Economy Horizon Scan And Needs Analysis, Sadaf Dalirazar, Mark Kelly, Derek Sinnott, James O'Donnell

Reports

The construction industry plays a crucial role in addressing the climate crisis as it is the largest global consumer of raw materials and contributes significantly to global energy consumption and emissions. Considering the world’s continuous population growth and the imperative to address infrastructure and housing demands the construction sector needs to adopt further sustainable strategies in its activities to reduce the pressure on natural resources. In addition, the Architecture, Engineering, and Construction (AEC) sector is responsible for generating substantial amount of waste known as Construction and Demolition Waste (CDW), which is projected to increase due to the future construction developments. …

Information Management And Bim Standards And Supports Inventory, Ryan Dempsey, Barry Mcauley, David Burke

Tools

The Digital Standards pillar consists of industry experts who champion the benefits of common rules, guidelines, and workflows that facilitate the improvement of information flow and information management across asset life cycles. Digital standards provide a common language that can be translated to technical specifications enabling clients, designers, contractors, and facilities managers, irrespective of their preferred tools, to communicate efficiently and reduce cost, rework, and disputes. Working closely with the Digital Procurement and Digital Education and Training pillars, this pillar is developing and delivering Irish Information Management/BIM (Digital Construction) guidelines for the sector.

This report summarises existing digital construction standards, …

Digital Construction Annual Survey 2022 Report, Davitt Lamon, Ted Mckenna

Reports

The Annual Survey 2022 was conducted to assess the state of digital transformation in the Irish construction and built environment sector. This report presents the analysis of survey data, with a focus on implications for the Build Digital project and Build Digital’s five pillars: Digital Leadership & Cultural Change, Digital Standards, Digital Education & Training, Digital Procurement, and Sustainability & Circular Economy. Key findings from the survey indicated that a significant number of organisations have started their digital transformation journey, with many identifying themselves as proactive and possessing a clear business-focused strategy. However, a considerable cohort of respondents are keen …

Steel Deck Diaphragms: Characterizing The Hysteretic Behavior Of Light Gage Steel, Screw-Fastened, Support And Sidelap Connections And The Influence Of Support Connections On The Stability Behavior Of Panels, Divyansh Kapoor

Doctoral Dissertations

Steel deck diaphragms are planar structures that serve as critical components of a metal building’s lateral force-resisting system. These can be found in walls, floors, and roofs of metal buildings and aid with the lateral stability of the structure. The diaphragm design process involves the selection of materials, deck geometry, connections, and connection detailing across the steel panels. The American Iron and Steel Institute’s AISI S310 and Steel Deck Institutes DDM04 both provide design guidance on the selection and detailing of materials and fasteners for the applicable limit states of connections and stability of the panels. Both design codes provide …

Effect Of Type And Quantity Of Inherent Alkali Cations On Alkali-Silica Reaction, Pengfei Ma, Jiaoli Li, Jincheng Bai, Ying Zhuo, Lingyu Chi, Yanping Zhu, Zhenhua Shi, Hongyan Ma, Genda Chen

Civil, Architectural and Environmental Engineering Faculty Research & Creative Works

In this study, the macroscopical expansion induced by alkali-silica reaction (ASR) and its corresponding ASR products are investigated using ordinary Portland cement (OPC) mortar specimens with a gradient of boosted alkalis. Experimental results show that the expansion increases with the concentration of inherent alkalis. Sodium-boosted samples expand approximately three times as much as potassium-boosted samples. ASR gels that are present in aggregate veins are calcium-free and amorphous; the atomic ratios of ASR gels are nearly independent of the type and quantity of alkali cations. Aggregate ASR gel exudation occurs in high (≥2.5 %) sodium cases and produces potential Na-shlykovite. Crystalline …

Ai-Based Bridge And Road Inspection Framework Using Drones, Hovannes Kulhandjian

Mineta Transportation Institute Publications

There are over 590,000 bridges dispersed across the roadway network that stretches across the United States alone. Each bridge with a length of 20 feet or greater must be inspected at least once every 24 months, according to the Federal Highway Act (FHWA) of 1968. This research developed an artificial intelligence (AI)-based framework for bridge and road inspection using drones with multiple sensors collecting capabilities. It is not sufficient to conduct inspections of bridges and roads using cameras alone, so the research team utilized an infrared (IR) camera along with a high-resolution optical camera. In many instances, the IR camera …

Meta-Analysis Of Insulated Concrete Wall Panel Design Methods For Shear And Flexure Behavior, Maryam Al-Bayati

Durham School of Architectural Engineering and Construction: Dissertations, Thesis, and Student Research

Insulated Concrete wall panels have been designed and constructed since the early 1950s with various shear ties, dimensions, and methods; nonetheless, thermal bridging and rational design are still a concern. Many companies have recently developed plastic connectors that have gradually replaced solid concrete sections and steel connectors due to their superior thermal efficiency and strength. However, there is no generally accepted method for predicting the behavior of sandwich wall panels in structural engineering practice or codes, but many methods have been used since the early 1920. This study aims to evaluate the accuracy of current methods for predicting the flexural …

Augmenting External Surface Pressures’ Predictions On Isolated Low-Rise Buildings Using Cfd Simulations, Md Faiaz Khaled, Aly Mousaad Aly

Faculty Publications

The aim of this paper is to enhance the accuracy of predicting time-averaged external surface pressures on low-rise buildings by utilizing Computational Fluid Dynamics (CFD) simulations. To achieve this, benchmark studies of the Silsoe cube and the Texas Tech University (TTU) experimental building are employed for comparison with simulation results. The paper is structured into three main sections. In the initial part, an appropriate domain size is selected based on the precision of mean pressure coefficients on the windward face of the cube, utilizing Reynolds Averaged Navier-Stokes (RANS) turbulence models. Subsequently, recommendations regarding the optimal computational domain size for an …

Semi-Annual Progress Report #12, Missouri University Of Science And Technology. Inspire - University Transportation Center

Semi-Annual Progress Reports

No abstract provided.

Robotic Inspection Of Infrastructure Using Vision, Gpr, And Impact-Echo Sensors, Jizhong Xiao

INSPIRE Archived Webinars

Bridges, dams, highways, and tunnels in the U.S. are reaching their life expectancy, and thus have imperative needs for routine inspection and maintenance to ensure sustainability. It is reported that 42% of over 600,000 highway bridges in the National Bridge Inventory (NBI) have exceeded their design life of 50 years, and 42,951 bridges are rated in poor condition and classified as "structurally deficient". To inspect the structurally integrity of bridges, the inspectors also need to detect subsurface defects (i.e., delamination, voids) using NDE instruments such as GPR and impact-echo (IE) device at difficult to access components (i.e., pier, bottom side …

An Investigation Into Ireland’S Bim Skills Gap, Guadalupe Centanni, Barry Mcauley

Conference Papers

The adoption of digital skills within the Irish AEC Sector has the potential to enhance efficiency and competitiveness among its stakeholders. Despite this opportunity, there is still a high demand for skilled BIM professionals, which cannot be currently met. To meet this skills demand and directly target future skills gaps within Ireland, several challenges must be addressed to facilitate broader BIM adoption. This paper focuses on addressing this gap by identifying steps to be followed to develop skilled professionals within BIM. This has been achieved by investigating the extent to which construction stakeholders in Ireland comprehend BIM and, examiningthe training …

Accelerating Bim Adoption In Ireland: A Ten-Year Review Of Cita Bim Gathering Proceedings, Alan Hore, Roger West, Barry Mcauley

Conference Papers

Digital construction interfaces have been studied extensively over the last few decades, with an ever-grow- ing catalogue of publications. The CitA BIM Gathering conferences have played a key role in bringing together the research and industry communities ina collaborative setting over the past decade in Ireland. In this paper the authors systematically review 10 years of papers published in the BIM Gathering pro- ceedings since the inaugural conference in 2013. A total of 175 papers involving over 200 authors have been reviewed and classified under the 2018 World Economic Forum (WEF) recommendations in respect to ac- celerating BIM adoption. The …

Industry Colloquium Report, Robert Moore

Reports

In the ever-evolving landscape of the construction industry, digital transformation has emerged as a pivotal force reshaping the way projects are conceived, executed, and delivered. This transformation, fuelled by cutting-edge technology and innovative practices, holds the promise of greater efficiency, sustainability, and collaboration within the construction sector.

This report offers a comprehensive summary of the Build Digital Project colloquium. It provides actionable insights and recommendations for clients, supply chain partners, and for prioritisation within the Build Digital Project pillars. As the industry partners seek to build a more efficient, sustainable, and collaborative construction sector, understanding and harnessing the invaluable insights …