Open Access. Powered by Scholars. Published by Universities.®
- Institution
- Publication
-
- CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018) (41)
- CCFSS Library (1939 - present) (3)
- CCFSS Newsletters (1999 - 2008) (2)
- CCFSS Technical Bulletins (1993 - 2020) (2)
- American Iron and Steel Institute (AISI) Specifications, Standards, Manuals and Research Reports (1946 - present) (1)
- Publication Type
Articles 31 - 51 of 51
Full-Text Articles in Engineering
Rotational Stiffnesses Of Semi-Rigid Baseplates, X. Feng, M. H. R. Godley, R. G. Beale
Rotational Stiffnesses Of Semi-Rigid Baseplates, X. Feng, M. H. R. Godley, R. G. Beale
CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)
The paper describes a test procedure to determine the rotational stiffnesses and moment-curvature relationships of semi-rigid baseplates of cold-formed structures. The influence of the modulus of the foundation subgrade on baseplate performance is determined. Increasing the axial load applied to a baseplate is shown to increase the ultimate moment-rotation capacity of a baseplate.
Fire Resistance On Bearing Wall Using Steel & Gypsum, In-Kyu Kwon, Kwang Choi, Jee Nam-Yong
Fire Resistance On Bearing Wall Using Steel & Gypsum, In-Kyu Kwon, Kwang Choi, Jee Nam-Yong
CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)
The conventional loadbearing wall systems generally used in Korea are composed of concrete and brick. Which materials have many defaults like long-term construction period and cost increase. Recently in us, a rapid increase in the usage of cold-formed steel section in housing and commercial building construction can widely be seen. The loadbearing wall assembly composed of light gauge-steel and gypsum board can preferably be applied to residential and commercial building of 5 stories or below. In order that light-gauge steel framing can be prevalently introduced in our domestic housing market, the wall assembly must have sufficient fire-resistant performance. Fire-resistant tests …
Seismic Design Of Light Gauge Steel Structures: A Discussion, Reynaud Serrette
Seismic Design Of Light Gauge Steel Structures: A Discussion, Reynaud Serrette
CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)
In a highly competitive and aggressive construction market, designers are always looking for new, proven ways to design safe, economical building structures. This is even more relevant in tract residential construction where a few dollars saved on one detail can affect who is awarded a project. In residential construction, a complete load bearing light gauge steel (LGS) system is now somewhat commonplace in the United States. Architects and engineers who once designed almost exclusively with other conventional materials are now consider LGS as an alternative. Although, it is feasible to make a direct substitution of LGS for conventional wood framing, …
Study On Light-Gauge Steel Roof Trusses With Rosette Connections, Pentti Makelainen, Jyrki Kesti, Olli Kaitila, Kimmo J. Sahramaa
Study On Light-Gauge Steel Roof Trusses With Rosette Connections, Pentti Makelainen, Jyrki Kesti, Olli Kaitila, Kimmo J. Sahramaa
CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)
This paper describes the Rosette-joining system and its possibilities in roof-truss structures in the span range of 8 to 12 meters (26 to 39 ft). The test programme that was carried out to verify the behaviour of the Rosette-joint and the thin-walled sections is described. The test results are given and analysed where they currently exist. The results are compared with values calculated according to the 1996 U.S. (AISI) [3] code supported by a distortional buckling analysis according to the Australian / New Zealand Standard (AS) [4] and FE Analysis results.
Testing Of Cold Formed Steel Floor Joists With Bearing Stiffeners, Reynaud M. Schuster, S. R. Fox
Testing Of Cold Formed Steel Floor Joists With Bearing Stiffeners, Reynaud M. Schuster, S. R. Fox
CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)
The application of lightweight steel framing (LSF) in residential construction has been growing in the past few years and is bringing forth some issues in Cold Formed Steel Design Specifications that need to be addressed. The area of interest of this paper is the requirement for bearing stiffeners in both the CSA-SI36(1) Standard and the AISI(2) Specification. Specifically, both of these documents require that all cross-sectional elements of a bearing stiffener must be fully effective. This restriction is difficult to meet in practice since almost all LSF members are subject to local buckling, hence are no longer fully effective. A …
A Study On The Flexural Behavior Of Profiled Composite Beams, Gu Rok Yang, Yong Seo Hwang, Young Bong Kwon
A Study On The Flexural Behavior Of Profiled Composite Beams, Gu Rok Yang, Yong Seo Hwang, Young Bong Kwon
CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)
An analytical study on the behavior of composite beams, which are composed of cold-formed steel sheeting and normal strength concrete, is described. An analytical method to trace the nonlinear behavior of a composite beam is developed to include the nonlinear material properties of steel sheeting, reinforcing steel bar and concrete. However, since the method is complex and tedious to use, two simple formulas for the nonlinear moment-curvature relation of the composite beam have been proposed. A simple power model, which has been originally used to predict the flexural capacity of the beam to column connections, is proposed as the first …
Cold-Formed Shear Connectors For Composite Constructions, Maximiliano Malite, Walter A. Nimir, Jose Jairo De Sales, Roberto Martins Goncalves
Cold-Formed Shear Connectors For Composite Constructions, Maximiliano Malite, Walter A. Nimir, Jose Jairo De Sales, Roberto Martins Goncalves
CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)
Construction employing composite steel-concrete structures has been increasingly applied in building and bridge structures, and solutions involving cold-formed profiles have recently appeared which, in many cases, have resulted in reduced costs. Because constructions using composite steel-concrete structures, involving cold-formed profiles, are not covered by current Brazilian Codes, it is necessary to investigate the issue. This paper, therefore, presents the results of an experimental analysis (24 push-out tests) made for two types of connectors: U-profile and angle, with two plate thicknesses: 2.65 mm and 4.76 mm, evaluating their strength and their load-slip behavior. The tests were performed on test specimens adapted …
Accelerated Test Development For Coil-Coated Steel Building Panels, K. M. Lawson, H. H. Lawson, H. E. G. Rommal, A. C. Tiburcio
Accelerated Test Development For Coil-Coated Steel Building Panels, K. M. Lawson, H. H. Lawson, H. E. G. Rommal, A. C. Tiburcio
CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)
This paper discusses the experimental design and the preliminary findings of an ongoing project designed to establish an accelerated laboratory test that would rank coating system performance the same as their performance in atmospheric exposure. A total of ten materials are included in the program: four substrates each with two coating systems and one substrate with two additional coating systems. Samples were installed at four atmospheric exposure sites: Middletown, OH, Daytona Beach, FL, Monroeville, PA, and Halifax, NS, Canada. Three different orientations were utilized at each of the exposure sites and a variety of building panel features were included on …
Ductility Measurements Of Thin G550 Sheet Steels, Colin A. Rogers, Gregory J. Hancock
Ductility Measurements Of Thin G550 Sheet Steels, Colin A. Rogers, Gregory J. Hancock
CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)
Cold formed structural members are fabricated from sheet steels which must meet various material requirements prescribed in applicable national design standards. These requirements ensure that; I) stress concentrations can be redistributed and 2) members and connections can undergo a minimum amount of displacement without a loss in structural performance. The Australian / New Zealand, AS/NZS 4600, and both North American, CSA-S136 and AlSI, Cold Formed Steel Design Standards allow for the use of thin (t < O.9mm), high strength (fy = 550MPa) sheet steels if the yield stress and ultimate strength are reduced to 75% of their minimum specified values. This paper provides a summary of results detailing the ductility and net cross-section tensile resistance of G550 sheet steels (to Australian Standard AS 1397) tested as solid and perforated coupons. Material properties of the test specimens are compared wIth the Dhalla and Winter requirements for ductility and ultimate strength to yield stress ratio. limit states tensile design equations are calibrated according to procedures defmed by the American Iron and Steel Institute (AlSI) Commentary.
Technique And Qualities Of Beams With Expanded Metal Sections, M. Hellsten
Technique And Qualities Of Beams With Expanded Metal Sections, M. Hellsten
CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)
The rotary expander technique can be used for manufacturing Lattice framework from a single strip of sheet metal by integrating expanded metal with solid sheet. This technique can be used to distribute the material in a tubular, or open profile to where it's best needed. Valuable qualities possible to are: - low weight and optimal strength - low energy transmission (noise and heat) - soft deformation and favorable energy absorbing properties - good fatigue resistance - high flexibility in design and product qualities These qualities are useful in applications like: - light and strong steel framing systems for buildings - …
Behaviour Of Thin G550 Sheet Steel Screwed Connections, Colin A. Rogers, Gregory J. Hancock
Behaviour Of Thin G550 Sheet Steel Screwed Connections, Colin A. Rogers, Gregory J. Hancock
CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)
This paper provides a summary of results detailing the behaviour of screwed connections tested in shear, which were composed of thin G550 and G300 sheet steels (to the 1993 Australian Standard AS 1397). Recommendations concerning the adequacy of current design standards with respect to the design of thin sheet steel screwed connections are made.
Understanding Pullover, Jonathan Sabia Kreiner, Duane S. Ellifritt
Understanding Pullover, Jonathan Sabia Kreiner, Duane S. Ellifritt
CCFSS Proceedings of International Specialty Conference on Cold-Formed Steel Structures (1971 - 2018)
Self drilling screws are often used for attaching roof and wall panels to structural framing and are subjected to tensile loads caused by negative wind pressures. Pullover failure is often associated with this loading condition, which occurs when It fastener pulls through a metal panel but remains attached to the structural framework underneath. The American lron and Steel Institute (AISI) has developed several standard tests for pullover and has included a design criterion for pullover in their specification. However, previous research at the University of Florida has found one particular test and the AISI Specification Section E4.4.2 to be un-conservative. …
Ccfss Technical Bulletin August 1998, Wei-Wen Yu Center For Cold-Formed Steel Structures
Ccfss Technical Bulletin August 1998, Wei-Wen Yu Center For Cold-Formed Steel Structures
CCFSS Technical Bulletins (1993 - 2020)
No abstract provided.
Ccfss News August 1998, Wei-Wen Yu Center For Cold-Formed Steel Structures
Ccfss News August 1998, Wei-Wen Yu Center For Cold-Formed Steel Structures
CCFSS Newsletters (1999 - 2008)
No abstract provided.
Fabrication Guidelines For Cold Bending (1998, Republished 2022), R. L. Brockenbrough & Associates, Inc.
Fabrication Guidelines For Cold Bending (1998, Republished 2022), R. L. Brockenbrough & Associates, Inc.
American Iron and Steel Institute (AISI) Specifications, Standards, Manuals and Research Reports (1946 - present)
To avoid cracking plates during cold bending, it is necessary to adopt a suitable minimum inside bend radius, which typically varies with plate thickness and grade. However, because of the addition of new plate grades over the years, it was suspected that current limits may not have been developed on a consistent basis. Therefore, the American Iron and Steel Institute (AISI) initiated a program to develop rational limits in 1998. This study was made to review information obtained in recent tests and develop suggested fabrication guidelines.
Investigating Performance Of Bonded Concrete Overlays, Norbert J. Delatte, David W. Fowler, B. Frank Mccullough, Stefan F. Gräter
Investigating Performance Of Bonded Concrete Overlays, Norbert J. Delatte, David W. Fowler, B. Frank Mccullough, Stefan F. Gräter
Civil and Environmental Engineering Faculty Publications
A bonded concrete overlay (BCO) is a concrete pavement rehabilitation method used to extend the life of an existing concrete pavement. The BCO should bond fully with the existing concrete, leading to a thicker composite pavement section, a much stiffer pavement, and a considerable decrease in pavement stresses. For one project, cost estimates for a BCO were half as much as for full-depth replacement of a pavement. In some cases BCOs have delaminated shortly after construction. This paper proposes a framework for identifying the causes of early age delamination in BCOs. The early age behavior of newly constructed BCOs is …
Design Of Automotive Structural Components Using High Strength Sheet Steels Effect Of Strain Rate On Material Properties And The Structural Strength Of Cold-Formed Steel Members, Wei-Wen Yu
CCFSS Library (1939 - present)
PREFACE The research work on automotive components conducted at the University of Missouri-Rolla under the sponsorship of the American Iron and Steel Institute began in 1982. During the first six years, studies were made on the basis of static loading. Since May 1988, studies have been concentrated on the effect of strain rate on material properties and the structural strength of cold-formed steel members along with the behavior of hybrid members. The research findings for the period from 1988 through 1997 are summarized in this report. Special thanks are expressed to General Motors Corporation (Dr M. Y. Sheh, Mr. B. …
Ccfss Technical Bulletin February 1998, Wei-Wen Yu Center For Cold-Formed Steel Structures
Ccfss Technical Bulletin February 1998, Wei-Wen Yu Center For Cold-Formed Steel Structures
CCFSS Technical Bulletins (1993 - 2020)
No abstract provided.
Ccfss News February 1998, Wei-Wen Yu Center For Cold-Formed Steel Structures
Ccfss News February 1998, Wei-Wen Yu Center For Cold-Formed Steel Structures
CCFSS Newsletters (1999 - 2008)
No abstract provided.
Design Of Automotive Structural Components Using High Strength Sheet Steels Transformed Section Method For The Calculation Of Yield Moment Of Cold-Formed Steel Hybrid Beams, Chi-Ling Pan, Wei-Wen Yu
Design Of Automotive Structural Components Using High Strength Sheet Steels Transformed Section Method For The Calculation Of Yield Moment Of Cold-Formed Steel Hybrid Beams, Chi-Ling Pan, Wei-Wen Yu
CCFSS Library (1939 - present)
INTRODUCTION It has been recognized that material properties and stress-strain relationships of sheet steel can be influenced by the strain rate. Because the member strength is also influenced by dynamic loading, a large number of research projects were conducted for a variety of structural members under specified loading conditions during past three decades. In cold-formed steel design, local buckling is one of the major design features because of the use of large width-to-thickness ratios for compression elements. For the purpose of determining the load-carrying capacity of automotive components, the effective width approach has been used. In view of the fact …
Nonlinear Modeling Of Concrete-Filled Frp Tubes Using The Finite Element Method, Kenneth T. Zagers
Nonlinear Modeling Of Concrete-Filled Frp Tubes Using The Finite Element Method, Kenneth T. Zagers
Retrospective Theses and Dissertations
Fiber reinforced plastic (FRP) has in recent years emerged as an alternative reinforcement for structural concrete. The properties that make FRP appealing to the construction industry include its resistance to electro-chemical corrosion, high strength-to-weight ratio, and electrical insulation. An efficient use of FRP is in the form of concrete-filled tubes, where the tube not only protects the concrete against environmental factors, but also provides confinement and external reinforcement. Since use of fiber composites for confining concrete is relatively new, analytical work in this area is limited to the models that were originally developed for transverse steel reinforcement. However, it has …