Engineering Commons^™

How Can We Build A Moral Robot?, Kristen E. Clark

Capstones

Artificial intelligence is already starting to drive our cars and make choices that affect the world economy. One day soon, we’ll have robots that can take care of our sick and elderly, and even rescue us in rescue us in emergencies. But as robots start to make decisions that matter—it’s raising questions that go far beyond engineering. We’re stating to think about ethics.

Bertram Malle and Matthias Scheutz are part of a team funded by the department of defense. It's their job to answer a question that seems straight out of a sci-fi novel: How can we build a moral …

A Continous Rotary Actuation Mechanism For A Powered Hip Exoskeleton, Matthew C. Ryder

Masters Theses

This thesis presents a new mechanical design for an exoskeleton actuator to power the sagittal plane motion in the human hip. The device uses a DC motor to drive a Scotch yoke mechanism and series elasticity to take advantage of the cyclic nature of human gait and to reduce the maximum power and control requirements of the exoskeleton. The Scotch yoke actuator creates a position-dependent transmission that varies between 4:1 and infinity, with the peak transmission ratio aligned to the peak torque periods of the human gait cycle. Simulation results show that both the peak and average motor torque can …

Roborodentia Robot, Jordan Dykstra, Anibal Hernandez, Robert Prosser

Computer Engineering

This report provides details on the design and implementation of a robot for the Spring 2015 Roborodentia competition. The system is described from a software perspective, a hardware perspective, and a mechanical design perspective.

Characterization Of A Robotic Manipulator For Dynamic Wind Tunnel Applications, James C. Lancaster

Theses and Dissertations

The newly acquired 6-DOF Motion Test Apparatus (MTA) was installed to perform dynamic wind tunnel testing in the AFIT Low Speed Wind Tunnel. Several complex motions revealed that the overall performance of the test rig needed improvement especially during small motions. The motions exposed that further enhancements would need to be performed individually for each joint. This research effort focused on the improvement of the MTA wrist roll motor and controller using a pitch oscillation. The controller software was improved using position feedback because the MTA wrist roll motor and controller exhibited reduced signal bias and amplitude attenuation. The enhanced …

An Opportunistic Service Oriented Approach For Robot Search, Dan Xie

Doctoral Dissertations

Health care for the elderly poses a major challenge as the baby boomer generation ages. Part of the solution is to develop technology using sensor networks and service robotics to increase the length of time that an elder can remain at home. Since moderate immobility and memory impairment are common as people age, a major problem for the elderly is locating and retrieving frequently used "common" objects such as keys, cellphones, books, etc. However, for robots to assist people while they search for objects, they must possess the ability to interact with the human client, complex client-side environments and heterogeneous …

Learning Parameterized Skills, Bruno Castro Da Silva

Doctoral Dissertations

One of the defining characteristics of human intelligence is the ability to acquire and refine skills. Skills are behaviors for solving problems that an agent encounters often—sometimes in different contexts and situations—throughout its lifetime. Identifying important problems that recur and retaining their solutions as skills allows agents to more rapidly solve novel problems by adjusting and combining their existing skills. In this thesis we introduce a general framework for learning reusable parameterized skills. Reusable skills are parameterized procedures that—given a description of a problem to be solved—produce appropriate behaviors or policies. They can be sequentially and hierarchically combined with other …

Multi-3d System: Advanced Manufacturing Through The Implementation Of Material Handling Robotics, Jose Luis Coronel Jr.

Open Access Theses & Dissertations

Since the rise of additive manufacturing (AM), innovation has been at the forefront. Additive Manufacturing systems that incorporate complex processes are steadily being developed. One example is the Multi3D System, which was designed to integrate the ability to print multi-material parts with that of embedding electronics. To achieve this automated process, the Multi3D incorporates a six-axis robotic arm to transfer a build platform containing a printed part, to various manufacturing stations (two fused deposition modeling (Stratasys, FDM400mc) systems and a computer numerical control router (Techno CNC Router). The robot is a Yaskawa Motoman MH50 chosen for its payload capacity of …

Generalized Mapping And Object Removal, Duncan Campbell

Williams Honors College, Honors Research Projects

Simultaneous localization and mapping (SLAM) is a problem that has been explored for the past few decades. SLAM deals with the concept of a robot being introduced into an environment in which it has no prior knowledge. Then, through the use of sensors, the robot is able to map its environment while simultaneously determining its position within the given area. While there has been extensive research into the development of methods by which this problem can be solved, not much has been done on what to do with the resulting maps once they are produced. The research conducted deals with …