Engineering Commons^™

The Fission Properties Of Curium Separated From Spent Nuclear Fuel, William Culbreth, Elizabeth Bakker, Jason Viggato

Separations Campaign (TRP)

Curium poses special problems in the chemical preparation of spent nuclear fuel for transmutation. Once separated from the other minor actinides, the seven curium isotopes in spent fuel can lead to nuclear fission with the subsequent release of a large amount of radiation. Several isotopes of curium also generate a significant amount of heat by radioactive decay. Sustained fission can be avoided by preventing the accumulation by more that a critical mass of curium. The heat generation of curium presents even more restriction on the mass of curium that can safely be contained in one location.

To analyze the nuclear …

Nuclear Criticality Analyses Of Separations Processes For The Transmutation Fuel Cycle: Quarterly Report, William Culbreth, Pang Tao

Separations Campaign (TRP)

During the first two quarters of the work, the tasks included training students in the use of Monte Carlo codes used in radiation transport studies and the assessment of neutron multiplication factors for specific problems outlined by ANL-East through Drs. Laidler and Vandegrift.

The proposal also included objectives for the first year of work on this project, as listed below. The work conducted in the second quarter of the project was in partial completion of these objectives.

• Train UNLV students in the use of SCALE and/or MCNP for the assessment of nuclear criticality.

• Assess neutron multiplication factor, k …

Design And Analysis Of A Process For Melt Casting Metallic Fuel Pins Incorporating Volatile Actinides, Yitung Chen, Darrell Pepper, Randy Clarksean

Fuels Campaign (TRP)

UNLV has developed and will continue to develop process models for the analysis of melt casting processes. This work will continue to be performed under the guidance of Argonne National Laboratory (ANL) engineers to ensure that their knowledge and experience benefits the project. The research to be conducted during the second year will center on performing detailed analyses on a conceptual design of an inductively heated skull-crucible casting furnace. Processing conditions will be analyzed, basic models utilized, and detailed heat and mass transfer models will be developed to analyze the most promising processes. The goal of this second year is …

Use Of Positron Annihilation Spectroscopy For Stress-Strain Measurements, Ajit K. Roy

Transmutation Sciences Materials (TRP)

The purpose of this collaborative research project involving the University of Nevada, Las Vegas (UNLV) and Idaho State University (ISU) is to evaluate the feasibility of determining residual stresses of welded (after pre-straining) engineering materials using a new nondestructive technique based on positron annihilation spectroscopy. The proposed technique is to use γ-rays 2 from a small MeV electron Linac to generate positrons inside the sample via pair production. This method can be used for materials characterization and investigation of defects in thick samples that could not be accomplished by conventional positron techniques or other nondestructive methods. The data generated will …

University Of Nevada, Las Vegas Advanced Accelerator Applications University Participation Program: Quarterly Report Fourth Quarter (December 2001 To February 2002), Anthony Hechanova

Transmutation Research Program Reports (TRP)

This Quarterly Report is a primary deliverable from the University of Nevada, Las Vegas (UNLV) Advanced Accelerator Applications (AAA) University Participation Program (UPP) Director to the U.S. Department of Energy (DOE) as described in the UNLV AAA proposal and Statement of Work for the Fourth Quarter.

The UNLV AAA UPP Director implements the program’s administration using staff from the Harry Reid Center for Environmental Studies (HRC) to ensure that work conducted under the UNLV AAA UPP meets program objectives. The UNLV AAA program consists of three components: Program Support, Research Infrastructure Augmentation, and Student Research.

Development Of A Mechanistic Understanding Of High-Temperature Deformation Of Alloy Ep-823: Aaa Task-10 Quarterly (12/1, 2001 –02/28, 2002) Report, Ajit K. Roy, Brendan O'Toole

Transmutation Sciences Materials (TRP)

The objective of this task is to evaluate the elevated temperature tensile properties of Alloy EP-823, a leading target material for accelerator-driven waste transmutation applications. The test material will be thermally treated prior to evaluation of its tensile properties at temperatures relevant to the transmutation applications. The deformation characteristics of tensile specimens, upon completion of testing, will be evaluated by surface analytical techniques including scanning electron microscopy (SEM) and transmission electron microscopy (TEM). The overall results are expected to provide a mechanistic understanding of high-temperature deformation behavior of Alloy EP-823 as a function of heat treatment.

Highlights of Accomplishment

• …

Environment-Induced Degradation And Crack-Growth Studies Of Candidate Target Materials: Aaa Task-4 Quarterly (December 1, 2001 – February 28, 2002) Report, Ajit K. Roy, Brendan O'Toole

Transmutation Sciences Materials (TRP)

The primary objective of this task is to evaluate the effect of hydrogen on environment-assisted cracking of candidate materials for applications in spallation-neutron-target (SNT) systems such as accelerator production of tritium (APT) and accelerator transmutation of waste (ATW). The materials selected for evaluation and characterization are martensitic stainless steels including HT- 9, EP 823 and 422. The susceptibility to stress corrosion cracking (SCC) and hydrogen embrittlement (HE) of these alloys will be evaluated in environments of interest using tensile specimens under constant load and slow-strain-rate (SSR) conditions. The extent and morphology of cracking of these alloys will further be evaluated …

Third Quarter Report, Covering January Through March 2002, John Farley

Transmutation Sciences Materials (TRP)

Progress from June 2001-November 2001 was presented at the winter meeting of the American Nuclear Society in Reno (November 12-15, 2001), and incorporated into a refereed conference proceeding. A copy of the refereed conference proceeding has been provided to Tony Hechanova. In brief, the paper described the new program to examine the corrosive effects of lead-bismuth eutectic (LBE) on steels. We employed various types of surface studies (Scanning Electron Microscope [SEM], and X-ray Photoelectron Spectrometry [XPS]) to examine steel samples that had been exposed to LBE for various lengths of time at various temperatures. The goal is to understand the …

Design And Evaluation Of Processes For Fuel Fabrication: Quarterly Progress Report #2, Georg F. Mauer

Fuels Campaign (TRP)

The second quarter of the project covered the following:

• Project review with Dr. Mitchell Meyer, ANL West: A project review of the transmuter fuels project was conducted during the January 2002 AAA meeting in Las Vegas.

• A second graduate student, Mr. Richard Silva, began working on the project. Rich will develop detailed 3-D process simulation models as his M.Sc. thesis project. Rich is employed with Bechtel at the Yucca Mountain project.

• AAA Seminar Presentation by Mr. Jae-Kyu Lee and G. Mauer. Title: Transmuter Fuel Fabrication Processes.

• More equipment detail and estimates were developed for different manufacturing …

Modeling Corrosion In Oxygen Controlled Lbe Systems With Coupling Of Chemical Kinetics And Hydrodynamics: Quarterly Progress Report 11/16/01- 2/15/02, Samir Moujaes, Yitung Chen

Transmutation Sciences Materials (TRP)

The Lead-Bismuth eutectic (LBE) has been determined from previous experimental studies by the Russians and the European scientific community to be a potential material that can be used as a spallation target and coolant for the AAA proposed application.

Properly controlling the oxygen content in LBE can drastically reduce the LBE corrosion to structural steels. However, existing knowledge of material corrosion performance was obtained from point-wise testing with very limited density. The transport of oxygen and corrosion products, their interaction and variation of corrosion/precipitation along the flow are not well understood.

The first subtask of this project involves using a …

Development Of A Systems Engineering Model Of The Chemical Separations Process: Quarterly Progress Report 11/16/01- 2/15/02, Yitung Chen, Randy Clarksean, Darrell Pepper

Separations Campaign (TRP)

The AAA program is developing technology for the transmutation of nuclear waste to address many of the long-term disposal issues. An integral part of this program is the proposed chemical separations scheme.

Two activities are proposed in this Phase I task: the development of systems engineering model and the refinement of the Argonne code AMUSE (Argonne Model for Universal Solvent Extraction). The detailed systems engineering model is the start of an integrated approach to the analysis of the materials separations associated with the AAA Program. A second portion of the project is to streamline and improve an integral part of …

Design And Analysis For Melt Casting Metallic Fuel Pins Incorporating Volatile Actinides: Quarterly Progress Report 11/16/01- 2/15/02, Yitung Chen, Randy Clarksean, Darrell Pepper

Fuels Campaign (TRP)

An important aspect of the Advanced Accelerator Applications (AAA) program is the development of a casting process by which volatile actinide element (i.e., americium) can be incorporated into metallic alloy fuel pins. The traditional metal fuel casting process uses an inductively heated crucible.

This process works well for the fabrication of metal fuel pins traditionally composed of alloys of uranium and plutonium, but does not work well when highly volatile actinides are included in the melt. The problem occurs both during the extended time period required to superheat the alloy melt as well as when the chamber must be evacuated. …

Hydrogen-Induced Embrittlement Of Candidate Target Materials For Applications In Spallation-Neutron-Target Systems, Ajit K. Roy, Brendan O'Toole

Transmutation Sciences Materials (TRP)

The purpose of this project is to evaluate the effect of hydrogen on cracking of candidate target materials for applications in spallation-neutron-target (SNT) systems such as accelerator production of tritium (APT) and accelerator transmutation of waste (ATW). The test materials will undergo appropriate thermal treatments prior to being hydrogen-charged by potentiostatic cathodic polarization technique in a simulated aqueous environment at different temperatures of interest. The specimens, upon completion of testing, will be metallographically examined. Further, the scanning electron microscopy (SEM) will be used to determine the extent and nature of cracking in the specimens tested. The thrust of the proposed …

Project Continuation Proposal: Radiation Transport Modeling Of Beam-Target Experiments For The Aaa Project, William Culbreth

Reactor Campaign (TRP)

The AAA program will rely on the use of an accelerator-based transmuter1 to expose spent nuclear fuel to high-energy neutrons. The neutron flux will be sufficient to activate or fission the long-lived isotopes of Tc, I, Pu, Am, Cm, and Np that present a significant radiological hazard in commercial spent fuel. Transmuter fuel will be subcritical and a high-energy proton accelerator is needed to maintain the necessary neutron flux through the use of a neutron spallation target. The maximum neutron energy produced by spallation (~ 800 MeV) is significantly higher than that produced by a commercial light water reactor (~ …

University Of Nevada, Las Vegas Transmutation Research Program Annual Report 2001, Anthony Hechanova, Elizabeth Johnson, Gary Cerefice

Transmutation Research Program Reports (TRP)

The UNLV Transmutation Research Program was established in March 2001 as part of the national Advanced Accelerator Applications program to develop the technologies necessary for the ecological and economical treatment of spent nuclear fuel.

The primary role of the UNLV program in the national effort is the training of graduate and undergraduate students in nuclear engineering and other related fields to support the augmentation of the U.S. human infrastructure for transmutation technologies.

To accomplish this role, UNLV has developed the TRP with the primary focus of supporting student research into transmutation and supporting technologies. This focus is realized through the …

Experimental Investigation Of Steel Corrosion In Lead Bismuth Eutectic (Lbe): Characterization, Species Identification, And Chemical Reactions, John Farley, Dale L. Perry, Allen L. Johnson

Transmutation Sciences Materials (TRP)

The goal of the present research is to achieve a basic understanding of corrosion of steels by Lead Bismuth Eutectic (LBE). Liquid LBE is under consideration in the transmuter as both a spallation target and as a blanket coolant. There have been previous studies of LBE, especially by the Russians, who have over 80 reactor-years experience with LBE coolant in their Alpha-class submarine reactors. However, a fundamental understanding and verification of its role in the corrosion of steels is still very incomplete. We have begun a program of post-experiment testing and analysis on steel samples that have been in intimate …

Corrosion Of Steel By Lead Bismuth Eutectic, John Farley, Dale L. Perry, Allen L. Johnson

Transmutation Sciences Materials (TRP)

This research program will analyze various steel samples that have been exposed to LBE as part of the national program to develop LBE and transmutation technologies. This information will be paramount in developing engineering efforts to control, avoid, and/or minimize the effect of corrosion of steels by LBE in transmuter and LBE systems. Additionally, this program provides UNLV researchers with hands-on experience that will be crucial in developing the UNLV LBE program, supporting the University’s mission with the ISTC target complex, and the future development of additional facilities to examine LBE systems.

The research group plans to test the hypothesis …

Corrosion Of Steel By Lead Bismuth Eutectic: Year 1 Annual Report, John Farley

Transmutation Sciences Materials (TRP)

The goal is to investigate the corrosion of stainless steel by lead-bismuth eutectic (LBE), which has been proposed for use as a blanket coolant and a spallation target in the transmuter.

Hydrogen-Induced Embrittlement Of Candidate Target Materials For Applications In Spallation-Neutron-Target Systems, Ajit K. Roy, Brendan O'Toole, Zhiyong Wang, David W. Hatchett

Transmutation Sciences Materials (TRP)

Spallation-neutron-sources, such as those under investigation for use in accelerator-driven transmutation systems, generate neutrons through the collision of high-energy protons, or charged hydrogen atoms, with heavy metal targets such as lead. As a result, these systems also tend to deposit a significant amount of hydrogen in the materials of the transmuter target and superstructure. This can result in accelerated corrosion and changes in the properties of the exposed materials. Of particular importance is a phenomenon called hydrogen embrittlement, in which materials lose their ductility (ability to deform under stress) and become brittle (more susceptible to fracture) after reacting with hydrogen. …

Modeling Corrosion In Oxygen Controlled Lbe Systems With Coupling Of Chemical Kinetics And Hydrodynamics: Task V 4th Quarterly Report, Samir Moujaes

Transmutation Sciences Materials (TRP)

The project is moving on target with the newly realigned objective set for the Phase I. Through close communications with Dr. Li and Dr. Jinsuo Zhang from LANL a realignment of the simulation work has been recommended. The reason for that is the vendor of STAR-CD/CHEMKIN had not perfected yet the final coupling of the post processing of output for any potential surface chemistry reaction taking place on the inside pipe surface of the LBE loop. This is because the coupling of CHEMKIN and STAR-CD has been done fairly recently.

Our final effort has been to generate using an innovative …

Modeling Corrosion In Oxygen Controlled Lbe Systems With Coupling Of Chemical Kinetics And Hydrodynamics, Samir Moujaes, Yitung Chen

Transmutation Sciences Materials (TRP)

Many of the international efforts to develop transmutation technology, including the U.S., Russian, and European scientific communities, have determined that lead bismuth eutectic (LBE) is a potential material for use as a both a spallation target and a coolant. To exploit this potential, a more thorough understanding of the effect and rates of corrosion on steels, particularly non-Russian alloys, inside the LBE systems is required. Properly controlling the oxygen content in LBE systems has been observed to drastically reduce the corrosion of structural steels in LBE. However, the transport of oxygen and formation of corrosion products is not well understood; …

Development Of A Mechanistic Understanding Of High-Temperature Deformation Of Alloy Ep-823, Ajit K. Roy, Brendan O'Toole

Transmutation Sciences Materials (TRP)

Alloy EP-823 has been developed as a structural material for Lead Bismuth Eutectic (LBE) systems, such as those under development for nuclear transmutation systems, as well as other applications. However, very little data regarding the mechanical properties of this alloy exists in the open literature, particularly in the temperature regime of interest for transmutation systems. To address this need, the UNLV research team, in collaboration with researchers from Los Alamos National Laboratory, has developed a research program to evaluate tensile properties of Alloy EP-823 stainless steel at elevated temperatures, which is not being performed at any other facility to date. …

Neutron Multiplicity Measurements Of Target/Blanket Materials, Carter D. Hull, William H. Johnson

Transmutation Sciences Physics (TRP)

To begin developing the database necessary for the validation and benchmarking of the LAHET component of the MCNPX code suite, the UNLV research program has set forth the following objectives. First, the current MCNPX suite will be used to develop models of multi-element neutron detector systems. These models of the detector systems will be incorporated into the design of detailed models for the entire detector-target system. These models will first be used to help design the irradiation experiments, and then will be used to model the behavior of the system. Irradiation experiments corresponding to the detector-target system models will be …

Nuclear Criticality, Shielding, And Thermal Analyses Of Separations Processes For The Transmutation Fuel Cycle, William Culbreth, Denis Beller

Separations Campaign (TRP)

The remediation of nuclear waste created by conventional fission reactors will rely upon the separation of the waste products for further treatment. The UREX+ process now under review will involve the use of an aqueous chemical process to separate out depleted uranium resulting in a product containing minor actinides, fission products, cesium, strontium, technetium, and iodine. The radioactive decay of strontium and cesium produces roughly half of the thermal and gamma production in spent fuel and the relatively short halflife of isotopes of both of these elements requires storage for about 300 years before heat and radiation decreases to safe …

Nuclear Criticality Analyses Of Separations Processes For The Transmutation Fuel Cycle, William Culbreth, Pang Tao, Denis Beller

Separations Campaign (TRP)

The separation and partitioning of used commercial reactor fuel is a vital component of any reprocessing or transmutation strategy. To process the high actinide fuels required for a transmutation effort, the Chemical Technology Division (CMT) at Argonne National Laboratory (ANL) is developing a pyrochemical separations process. Currently, this work is being done via small experiments. While this is more than sufficient to develop the technologies required to process actinide-bearing fuels, it does not allow for the direct investigation of criticality concerns that would be present in larger systems. As the volume of waste to be treated increases, a higher probability …

Design And Analysis Of A Process For Melt Casting Metallic Fuel Pins Incorporating Volatile Actinides, Yitung Chen, Darrell Pepper, Randy Clarksean

Fuels Campaign (TRP)

The Transmutation Research Program requires the incorporation of non-fertile actinides into the fuel matrix for the transmuter blanket. One of three currently proposed candidate matrices for the transmuter blanket is a metallic alloy fuel matrix. Metallic fuels are an outstanding candidate for a transmutation fuel due to excellent irradiation performance and ease of fabrication. However, including a volatile constituent during fabrication of these fuel pins presents a challenge. High vapor pressure actinides, particularly americium, are susceptible to rapid vaporization and transport using traditional metal fuel casting processes. As a result, only a fraction of the desired charge is incorporated into …

A Dynamic Simulation Model Of Beach Sand Replenishment: A Case Study Of Santa Barbara, California, David Turbow, Steve Norwick, Sajjad Ahmad

Civil and Environmental Engineering and Construction Faculty Research

Sediment deprivation from dam installments contributes to beach erosion yet the underlying physical and economic factors linking them together have traditionally been isolated during regional planning. In order to gain a better understanding of the behavior of a managed beach system, a dynamic simulation model was developed incorporating physical and monetary factors influencing the amount of available beach sand. The Santa Barbara littoral cell was chosen as a case study to evaluate the feasibility of beach preservation goals under scenarios in which annual sand replenishment funding, sand prices, or sediment recovery from behind dams were limiting factors to available beach …

Biological Reduction Of Perchlorate In Ion Exchange Regenerant Solutions Containing High Salinity And Ammonium Levels, Tina M. Gingras, Jacimaria R. Batista

Civil and Environmental Engineering and Construction Faculty Research

The most promising technologies to remove perchlorate from water are ion exchange and biological reduction. Although successful, ion exchange only separates perchlorate from water; it does not eliminate it from the environment. The waste streams from these systems contain the caustic or saline regenerant solutions used in the process as well as high levels of perchlorate. Biological reduction could be used to treat the regenerant waste solutions from the ion exchange process. A treatment scheme, combining ion exchange and biodegradation, is proposed to completely remove perchlorate from the environment. Perchlorate-laden resins generate brines containing salt concentrations up to 6% or …