Engineering Commons^™

A Comparison Of The Aerodynamic Centers For Panel Code Compressible Corrections And Openfoam 5 For Mach 0.1 To 0.8, Dustin Weaver

All Graduate Plan B and other Reports, Spring 1920 to Spring 2023

It is known that the aerodynamic center changes from quarter chord to half chord from incompressible to compressible flows on airfoils. Compressible corrections are derived and implemented in a vortex panel code. These results will be used to find the aerodynamic centers for the specified Mach range of 0.1 to 0.8 in 0.1 increments within - 6 to 6 degrees angle of attack. OpenFOAM 5 cases will be created with specific meshes and settings. The results calculated from OpenFOAM 5 will be compared to the results obtained from the compressible corrections.

The Vibe, Sarah P. Douglass

Capstones

The Vibe is a long-form narrative about where tech is taking the female orgasm. The piece concludes that physiological research is a required next step when creating the climax of the future.

http://sarahpdouglass.com

Boat-Lift Design And Analysis, Nathan Schick

Honors Theses

A current in production 6000 lb. rated boat-lift is being sold at “Great Lake Lifts”. The lift was tested experimentally and proved to hold at least 8000 lb. The design team successfully modeled the current lift on Ansys to help the customer understand where the weakest points in the design were. Following the creation of the initial lift design, the design team proposed and tested modifications that could be made in order to make the lift more structurally sound. The initial lift had a maximum deflection of 0.43846 inches, a maximum stress of 15880 psi, and a safety factor of …

Dyno-Mite Redesign, Brandon Joseph Miller, Daniel Robert Hoffman, Richard Demedici Young

Mechanical Engineering

The Cal Poly Mechanical Control Systems Laboratory currently employs an outdated device, known as the Motomatic, to teach students about various motor characteristics and control methods. These include open-loop vs. closed-loop control, speed vs. position control, and DC motor response curves. The current device does not function properly and produces unreliable data due to overwhelming non-linear effects such as stiction and shaft misalignment. Our team was tasked with designing a replacement device that retains many of the same educational goals as the original lab procedure, while also adding new educational goals pertaining to the device system dynamics. The new apparatus, …

Development Of An Insulated Solar Electric Cooker (Isec) With Thermal Storage For Use In Developing World Countries, Amanda Gyokery, Spencer W. Davis, Kyle Henry Smit

Mechanical Engineering

According to the World Health Organization, about half of the world’s population uses biomass stoves to cook their meals. However, biomass fires can be dangerous. Unattended biomass fires and indoor air pollution are responsible for an estimated 600,000 deaths annually and the creation of approximately 4 million instances of chronic disease. They also release CO2 and other pollutants into the air, and require the families to gather enough material to keep it burning (WHO 2017). Although cleaner cooking technology seems like a clear solution, often families are either unwilling to change how they cook food or are unable to afford …

Sound-Proof, Fire Resistant, Leak-Free And Super-Insulated Hvac Ducts, James Fitzsimmons Ii, Ahmed Alyousef, Kyle Dirksen, Nathan Ware, William Miller

Chancellor’s Honors Program Projects

No abstract provided.

Free-Surface Wall-Jet Flow At Moderate Reynolds Number As Applied To Slot And Blade Coating, Mohammad Tanvir Hossain

Electronic Thesis and Dissertation Repository

The flow of a two-dimensional steady wall jet observed in the slot and blade coating processes has been examined theoretically near the channel exit. The Newtonian free surface jet emerges from a channel and deposits onto an infinite moving wall with an adverse or favorable pressure gradient applied inside the channel. The Reynolds number considered is within the moderate range, and fully developed Couette-Poisueille flow conditions are assumed to prevail far upstream inside the channel. The effects of inertia and pressure gradient on the velocity, the shape of the free surface, and the stress are emphasized. It is found that …

Numerical, Analytical, And Experimental Studies Of Reciprocating Mechanism Driven Heat Loops For High Heat Flux Cooling, Olubunmi Tolulope Popoola

FIU Electronic Theses and Dissertations

The Reciprocating Mechanism Driven Heat Loop (RMDHL) is a novel heat transfer device that utilizes reciprocating flow, either single-phase or two-phase flow, to enhance the thermal management in high tech inventions. The device attains a high heat transfer rate through a reciprocating flow of the working fluid inside the heat transfer device. Although the concept of the device has been tested and validated experimentally, analytical or numerical studies have not been undertaken to understand its working mechanism and provide guidance for the device design. The objectives of this study are to understand the underlying physical mechanisms of heat transfer in …

Method For Single Crystal Growth Of Photovoltaic Perovskite Material And Devices, Jinsong Huang, Qingfeng Dong

Department of Mechanical and Materials Engineering: Faculty Publications

Systems and methods for perovskite single crystal growth include using a low temperature solution process that employs a temperature gradient in a perovskite solution in a container , also including at least one small perovskite single crystal , and a substrate in the solution upon which substrate a perovskite crystal nucleates and grows , in part due to the temperature gradient in the solution and in part due to a temperature gradient in the substrate . For example , a top portion of the substrate external to the solution may be cooled .

The Rheology And Roll-To-Roll Processing Of Shear-Thickening Particle Dispersions, Sunilkumar Khandavalli

Doctoral Dissertations

Particle dispersions are ubiquitous in our daily lives ranging from food and pharmaceutical products to inks. There has been great interest in the recent years in formulation of functional inks to fabricate myriad flexible electronic devices through high-throughput roll-to-roll technologies. The formulations often contain several functional additives or rheological modifiers that can affect the microstructure, rheology and processing. Understanding the rheology of formulations is important for tuning the formulation for optimal processing. This thesis presents investigations on the rheology of particle dispersions and their impact on roll-to-roll technologies. Shear-thickening behavior is common in particle dispersions, particularly, concentrated particulate inks. We …

Medium Duty Gas-Turbine Engine Blade Removal Tool, Elliott James Greb, Jacob Thomas Syage, Kellen Thomas Field

Mechanical Engineering

Solar Turbines Incorporated sponsored a team of three Cal Poly Undergraduate Mechanical Engineering students to design, manufacture, prototype, and test a tool for the removal of turbine blades from their respective disk assembly without damaging the disk itself. The tool was developed for Solar’s industrial gas turbine engines. The tool complies with all OSHA and Solar Turbines safety and engineering constraints, and was designed for use in a shop facility. The tool was made adaptable for geometric variances in multiple turbine rotor disk stages, and requires no more than one technician to operate using a maximum of two shop resources. …

Animated Otto-Langen Atmospheric Engine, Keiran M. Hansen, Lance Hodgson, Rachel A. Jakob, Chris J. Splees

Mechanical Engineering

Based on an existing relationship between Dr. Owen and the Deutsches Museum, Otto-Mated was given the opportunity to collaborate with the two in a year-long senior design project. Otto-Mated was tasked with modeling and simulating the Otto-Langen Atmospheric Engine as a form of preservation and education. The model was created in SolidWorks and animated in Blender, effectively providing the museum with accurate and educational videos demonstrating the engine’s function. Within this document are the plans, decisions, and processes used to create our final product for Deutsches Museum.

Oct-Based Three Dimensional Modeling Of Stent Deployment, Pengfei Dong, David Prabhu, David L. Wilson, Hiram G. Bezerra, Linxia Gu

Department of Mechanical and Materials Engineering: Faculty Publications

Stent deployment has been widely used to treat narrowed coronary artery. Its acute outcome in terms of stent under expansion and malapposition depends on the extent and shape of calcifications. However, no clear understanding as to how to quantify or categorize the impact of calcification. We have conducted ex vivo stenting characterized by the optical coherence tomography (OCT). The goal of this work is to capture the ex vivo stent deployment and quantify the effect of calcium morphology on the stenting. A three dimensional model of calcified plaque was reconstructed from ex vivo OCT images. The crimping, balloon expansion and …

Anchoring And Stiffening Techniques For Portable Concrete Barriers, Surajkumar Bhakta

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

Portable concrete barrier (PCB) systems are utilized on federal and state highways in circumstances such as placing adjacent to vertical drop-offs and in construction zones. PCB systems are most commonly used in a free-standing configuration, which are known to have relatively large deflections when impacted. Large deflections are undesirable when dealing with limited space. In order to allow PCBs to be used in space restricted locations, seven PCB anchoring and stiffening techniques were tested and evaluated as per Manual for Assessing Safety Hardware (MASH) testing standards. Results will allow the New Jersey Department of Transportation to update guidance for their …

Non-Equispaced Fast Fourier Transforms In Turbulence Simulation, Aditya M. Kulkarni

Masters Theses

Fourier pseudo-spectral method on equispaced grid is one of the approaches in turbulence simulation, to compute derivative of discrete data, using fast Fourier Transform (FFT) and gives low dispersion and dissipation errors. In many turbulent flows the dynamically important scales of motion are concentrated in certain regions which requires a coarser grid for higher accuracy. A coarser grid in other regions minimizes the memory requirement. This requires the use of Non-equispaced Fast Fourier Transform (NFFT) to compute the Fourier transform, by solving a system of linear equations.

To achieve similar accuracy, the NFFT needs to return more Fourier coefficients than …

Electroless Deposition & Electroplating Of Nickel On Chromium-Nickel Carbide Powder, Jeffrey Rigali

Masters Theses

Engineered components can gain desirable properties when coated with surface materials. Wear-resistant coatings can improve the performance of contacting surfaces and allow for an extended life of the parts. Hard chromium has been the plating material of choice for certain wear and corrosion- resistant coatings because of its desirable combination of chemical resistance, adhesion, and mechanical properties. However, hexavalent chromium, a component of the process for applying hard chromium coatings, has been recognized by the EPA as having hazardous health and environmental impacts. Existing and planned environmental regulations restricts the use of process chemicals containing hexavalent chromium ions. This substantiates …

Improving The Efficiency Of Wind Farm Turbines Using External Airfoils, Shujaut Bader

Masters Theses

Wind turbine efficiency typically focuses on the shape, orientation, or stiffness of the turbine blades. In this thesis, the focus is instead on using static fixed airfoils in proximity to the wind turbine to control the airflow coming out of the turbine. These control devices have three beneficial effects. (1) They gather air from “higher up” where the air is moving faster on average (and therefore has more kinetic energy in it). (2) They throw the used (and slowed down air) downwards. This means that any turbines in the wind farm behind the lead turbines do not get “stale” air. …

How Spaceflight Affects The Detachment Of Zinc Whiskers, Kayla Capitan

Von Braun Symposium Student Posters

No abstract provided.

Predicting Mechanical Properties Of Lattice Structures, Behzad Bahrami Babamiri

Von Braun Symposium Student Posters

No abstract provided.

Floating-Gate Transistor Photodetector, Jinsong Huang, Yongbo Yuan

Department of Mechanical and Materials Engineering: Faculty Publications

A field effect transistor photodetector that can operate in room temperature includes a source electrode , a drain electrode , a channel to allow an electric current to flow between the drain and source electrodes , and a gate electrode to receive a bias voltage for controlling the current in the channel . The photodetector includes a light - absorbing mate rial that absorbs light and traps electric charges . The light absorbing material is configured to generate one or more charges upon absorbing light having a wavelength within a specified range and to hold the one or more charges …

The Development And Numerical Modelling Of A Representative Elemental Volume For Packed Sand, Ashraf Thabet

Electronic Thesis and Dissertation Repository

The motivation of this thesis is the development of simple microscopic-scale model (representative elemental volume; REV) that can be used to conduct flow and heat transfer simulations from which closure coefficients can be established for the volume-averaged transport equations for porous media (packed bed). The thesis provides a brief introduction to the computational technique adopted for the geometric generation of the REV (YADE), followed by a parametric study undertaken to reveal the minimum number of particles inside the REV that are required to mimic the appropriate physics. Additional analysis was conducted with the goal of determining the influence of deviation …

Numerical Simulations Of Two-Phase Flows In The Liquid Solid Circulating Fluidized Bed, Hao Luo

Electronic Thesis and Dissertation Repository

The liquid-solid circulating fluidized bed (LSCFB) has many potential applications in biochemical and petroleum industries, as well as in wastewater treatments, given its higher contact efficiency and being able to accommodate two reactions under one system. With extensive experimental results becoming available, there is clearly a need for computational fluid dynamics (CFD) modeling to expand our understandings of LSCFBs and to predict the hydrodynamic behaviors of the two-phase flows within LSCFB.

In this research, the Eulerian-Eulerian two-phase model combined with the kinetic theory for the granular phase is applied to simulate the two-phase flows in LSCFBs. The key factors affecting …

Experimental Measurements Of Far Field Cough Airflows Produced By Healthy And Influenza- Infected Human Subjects, Ahmed Faraj Alarbi Mohamed

Electronic Thesis and Dissertation Repository

The present work details an experimental study of the cough airflow fields produced by subjects infected with influenza and when they are convalescent, together with data from healthy cohorts. The PIV and HWA measurements were taken far downstream at 1 m from the source within a cough chamber, along with droplet sampling at two different locations and nasal swabs from the sick subjects. The measured data over different seasons were used to evaluate and compare the results from sick, convalescent and healthy subjects. Although a total of 8 sick participants from winter 2014 and 2017 yielded positive nasal swab analysis, …

Optimization Of The Hot Embossing Parameters And Sintering Characterization For Alumina/Berea Sandstone Sintering, Justin F. Robbins

LSU Master's Theses

The purpose of this study is to investigate the process of hot embossing on alumina based ceramics as a cost-efficient procedure for manufacturing microfluidic testing components. Alumina ceramics were used as an exploratory phase for the final objective of the project, manufacturing of Berea sandstone based ceramic samples. Previous research has shown potential in using hot embossing on Alumina based ceramics; however, complications with extrusion and micro-structure quality were observed. For this reason, the research performed aimed to produce Berea Sandstone based components by first improving upon the embossing quality of alumina ceramics.

The thesis first investigates changes in the …

Software For Extracting Deformation Gradient And Stress From Md Simulations: Simulations Using The Charmm Force Field, Mehrdad Negahban, Lili Zhang, Zesheng Zhang, John Jasa, Antoine Jérusalem

Department of Mechanical and Materials Engineering: Faculty Publications

Software was developed, and is provided under a general use license, to calculate continuum level deformation gradient and stress for any group of atoms in an MD simulation that uses the Charmm force fields. This software can also calculate the interaction stress applied by one group of atoms on any other group. To obtain deformation gradient and stress, the user needs to provide the selected group(s) of atoms in an atom group identification file, and provide the associated LAMMPS format files and force field parameter file. An example is included to demonstrate the use of the software.

Energy Absorbing Guardrail System, John R. Rohde, John D. Reid, King K. Mak, Dean L. Sicking

Department of Mechanical and Materials Engineering: Faculty Publications

A highway crash attenuation system having W - beam rail elements attached to a plurality of vertical posts . An impact terminal with a feeder chute guides one or more of the W - beam rail elements through the impact terminal . The feeder chute has an impact shield extending along a traffic facing side of the chute from an upstream - most end to a downstream - most end of the chute closing the traffic - facing side of the chute . The system also has an anchor cable release mechanism for releasing the cable downstream of the first …

Design, Analysis, And Verification Of An Open-Wheeled Formula-Style Race Car Suspension System, Joshua Beckerman

Honors Capstone Projects - All

This honors thesis presents the design, measurement, and analysis of an open-wheeled formula racecar suspension system. This racecar is the second iteration of Syracuse University’s Citrus Racing team student competition vehicle. The race car’s suspension system features several designs that enable geometric adjustability to impact the vehicles dynamic performance. The purpose of this research is to find an analytic approach to verifying the correlation between suspension design tunings and their effect on vehicle handling and road holding capacity. This was done by analyzing measured data obtained from a system of damper-mounted travel sensors as the vehicle drives through numerous realistic …

Shape-Adaptive Mechanism For Robotic Grasping, Carl A. Nelson

Department of Mechanical and Materials Engineering: Faculty Publications

A grapser can include a first pantograph cell and a second pantograph cell coupled with the first pantogrpah cell. The first and second pantograph cells can be coupled together at a first pivot and a second pivot. The grasper can also include a finger extendable in a direction extending between the first pivot and the second pivot. The grasper can include a support base, where one or more links of the first pantograph cell can be slidably coupled with the support base for extending the grasper. In some embodiment, the grasper can be configured to extend along a curved path. …

Analytical Solution Of Microbes Interacting With Surfaces, Junyuan Li, Arezoo M. Ardekani

The Summer Undergraduate Research Fellowship (SURF) Symposium

Nowadays, there is a rising interest in studying the behavior of microbes and their interactions with flow and surfaces. In order to explore the velocity field, pressure and forces around the microbes, the solution of Stokes equations, which is called a Stokeslet, is used. This solution represents a singular velocity field due to a concentrated external force acting on fluid at a single point. This singularity could cause the expression of velocity not integrable. We use the Regularized Stokeslet Method and Method of Images to deal with this problem. The expression of force is replaced by a radially symmetric function, …

Development Of Portable Hyperspectral Imaging Device, Chenxi Li, Youngkee Jung, Iyll-Joon Doh, Euiwon Bae

The Summer Undergraduate Research Fellowship (SURF) Symposium

Most of the conventional hyperspectral imaging devices require sophisticated optical components, occupy a large footprint, and requires an initial capital investment for laboratories which mostly suits for laboratories benchtop system. The requirement of shipping the sample and waiting an extended period of time to get the results are the main downsides of this traditional approach. Capitalize in many specific field applications and diagnosis, portable devices provide both convenience and on-site results which are desirable for government agencies and food safety inspectors. This project was aimed to develop a low-cost, portable hyperspectral device for food safety applications. A smartphone was used …