Engineering Commons^™

Analysis Of Biomass/Coal Co-Gasification For Integrated Gasification Combined Cycle (Igcc) Systems With Carbon Capture, Henry A. Long Iii

University of New Orleans Theses and Dissertations

In recent years, Integrated Gasification Combined Cycle Technology (IGCC) has become more common in clean coal power operations with carbon capture and sequestration (CCS). Great efforts have been spent on investigating ways to improve the efficiency, reduce costs, and further reduce greenhouse gas emissions. This study focuses on investigating two approaches to achieve these goals. First, replace the subcritical Rankine steam cycle with a supercritical steam cycle. Second, add different amounts of biomass as feedstock to reduce emissions. Finally, implement several types of CCS, including sweet- and sour-shift pre-combustion and post-combustion.

Using the software, Thermoflow®, this study shows that utilizing …

Golf Club Quality Control Device, David Mcdermott, Mark Severy

Mechanical Engineering

No abstract provided.

Residential Attic Ventilation In A Hot And Humid Climate: Effects Of Increased Ventilation On Thermal Performance And Moisture Control, Stanley Arthur Atherton

Masters Theses

The reality of the effect of natural ventilation in a residential attic cavity has been the topic of many debates and scholarly reports since the 1930’s. The purpose of ventilating an attic cavity is to prevent collection of condensate on the structural surfaces, and to create a thermal buffer between the conditioned space and the ambient air. The current standards are not specific to climate zone, despite the fact that each climate zone may require ventilation for very different reasons.

To address the issue of ventilation effects in a hot and humid climate, a Natural Exposure Testing facility was constructed …

Thermocouple Temperature Measurements For Twin Jet Thermal Mixing, Spero Michael Peters

Masters Theses

Thermocouples are commonly used devices for temperature measurement. This study concerns the implementation of thermocouples to collect thermal mixing data in an environment in which two parallel water jets are mixing. The measurements are taken with the purpose of modeling the jet mixing region so that Computational Fluid Dynamics (CFD) models can be validated against the test data. This thesis covers the design, construction, implementation and evaluation of a thermocouple system for immersion in a water environment to measure the thermal mixing of twin jets.

The measurement system being used is a thermocouple rake whose design and fabrication is covered. …

Wireless Solar-Powered Thermal Imaging Camera, Andy Bonk, Billy Mcvicker, Jacob Richardson

Mechanical Engineering

Creation of a mounted wireless self-powered thermal imaging camera system.

Engine Simulation And Diagnostic Test Bed: Final Design Report, Jeff Lewis, Cody Scott, Todd Smith

Mechanical Engineering

The San Luis Obispo High School Automotive Technology Shop has a 1991 Buick V-6 Engine which uses the OBD-I (On-Board Diagnostics, generation one) standard for diagnostic testing and troubleshooting. In order to expand the capabilities of the Automotive Technology program and allow students to gain first-hand experience troubleshooting older OBD-I engines, the shop has a need for this engine to become part of a diagnostic and troubleshooting test bed. Some of the diagnostic tests the students will perform include checking cylinder pressure, monitoring coolant system temperatures, interpreting error codes from the OBD-I system, and conducting enhanced smog testing. All of …

Wiihopp, Jeff Christian, Ben Hoselton, Derek Simon

Mechanical Engineering

Childhood obesity is becoming a growing problem in the United States. According to the CDC, childhood obesity has more than tripled in the past 30 years [7]. It can lead to health problems previously reserved for adults, such as diabetes, high blood pressure, and high cholesterol. For the team WiiHopp project, we plan to turn a JumpSport mini-trampoline into a controller for the Nintendo Wii console. The hope is to help turn the problem of video games and the laziness surrounding them into an active solution to combat the problem of childhood obesity.

Our goal is to produce an add-on …

Access|Closure Balloon Catheter Redesign Project, Keenan Bamburg, Yvette Castillo, Elizabeth Eskildsen

Mechanical Engineering

No abstract provided.

Engineering On The Rose Float: Final Project Report, Stephen Boles, Garrett Dong, Peter Hoonhout

Mechanical Engineering

The purpose of this project is to design the simple mechanical movement systems of the 2012 Cal Poly Tournament of Roses Float Parade to prevent failure. Three mechanisms were designed. One of the mechanisms is a tall building that has a superhero and helicopter rotating around the top; it also has the ability to rotate the top 2/3^rds of the mechanism to a 90 degree angle to fit under a 16.5 foot bridge. Another mechanism is the cars that look like they are driving on the pod’s road surface via train tracks underneath the surface. The cars will travel …

California Polytechnic State University Wind Resource Assessment, Jason Allan Smith

Master's Theses

Wind resource assessment at California Polytechnic State University shows there is potential for wind power generation on Cal Poly land. A computational fluid dynamics model based on wind data collected from a campus maintained meteorological tower on Escuela Ranch approximately 5 miles northwest of campus suggests there are areas of Cal Poly land with an IEC Class III wind resource at a height of 80 meters above ground. In addition during the daytime when the campus uses the most energy there are large portions of land with annual average daytime wind speeds above 6.9m/s. These areas have been identified by …

Effects Of Supercooled Water Ingestion On Engine Performance, Rick Hutchings

Masters Theses

An aircraft will encounter freezing rain, snow, and ice during ground operation and flight. In cold conditions, ice may form on th einlet and internal stators and rotors of the gas turbine engine. When ice accumulates on blades (and/or stators), the aerodynamic characteristics of the blades change due to the altered size, shape, and roughness. This change causes the blade to no longer operate at its design point and decreases compressor performance. Therefore, characterization of the aerodynamic performance is required to define the associated losses due to the effects of supercooled liquid water ingestion. This characterization can be accomplished through …

Pop-A-Wheelie Design Team, Mackenzie Hill, Thuyen Nguyen, Shaun Van't Hul

Mechanical Engineering

The purpose of this report is to illustrate the Pop-a-Wheelie design team’s progression and implementation of a concept in regards to the project sponsored by Break the Barriers (BTB). The Pop-a-Wheelie design team was tasked to design two devices that will be attached onto wheelchairs. The devices should facilitate the independence of user’s ability to pop-a-wheelie and return to an upright position without any assistance. After a list of specifications was agreed upon, the design process initiated. All customer specifications are listed in Objectives section located in Chapter 1: Introduction. A complete engineering specification table can be found in the …

Cal Poly Human Powered Helicopter, Josiah Auer, Eric Behne, Dave Berry, Rebecca Hennings, James Koch, Ian Marquardt, Josiah Mayfield, Sean Miller

Mechanical Engineering

The following report encompasses the Cal Poly Human Powered Helicopter team’s efforts during the 2010-2011 academic year. The intention of this project is to further the knowledge of human powered helicopter design and to validate an ideal configuration through experimental tests and analysis.

A. Background

The Sikorsky Prize offered by the American Helicopter Society has been the catalyst for many attempts at Human Powered Helicopter (HPH) flight. The requirement to win the prize is a continuous, human powered flight of more than 60 seconds that stays within a 10 meter square box and reaches an altitude greater than 3 meters …

Thermodynamic Based Model Eliciting Activities For Undergraduate Mechanical Engineering Education, Paul Nicholas Van Bloemen Waanders

Master's Theses

Undergraduate engineering education is designed to prepare students for their careers. The rise of technology in modern engineering allows for a shift in the way undergraduates are prepared for the modern workplace. Model Eliciting Activities (MEAs) allow students to think critically about their own work and allow instructors to analyze the students’ problem solving methods. To ensure that new MEAs are as effective as possible they are subject to six basic principles: model construction, reality, generalizability, self-assessment, model documentation, and effective prototype.

This document focuses on evaluating new MEAs for their adherence to the six principles from an instructor's and …

Marauder Marine: Spearfishing Float Design, Kevin Glen, Kyle Lancaster, Andrew Wickham

Mechanical Engineering

No abstract provided.

Olympic Bocce Ballers, Steven Erickson, William Haley, Taylor Vaughan

Mechanical Engineering

No abstract provided.

Solar Powered Oil Well Site, Jonathan Hyland, Matthew Mastro, Kyle Moore

Mechanical Engineering

No abstract provided.

Piedras Blancas Light Station Vista Point Improvement Plan, Larissa Heeren, Reuben Juster, Annamarie Usher, John Rossi, Nick Mitchell

Mechanical Engineering

Piedras Blancas Light station Improvement Involved the design of two separate parking lot/vista point plans as well as the creation of a concrete Iron Ranger located near the gift shop on site.

Bevcool, Matthew (Matt) Slette, Ryan Talyat, Camille Sybert

Mechanical Engineering

A consumer product for rapidly cooling canned and bottled beverages.

Optimization And Modeling Tools For Telescope Hexapod Structures, Michael Edward Feeney

Master's Theses

Hexapod trusses are an important element in many mechanical design systems. The natural frequency and stiffness behavior under geometric and mass variations of such structures is largely undocumented. Furthermore, the ability to quickly model hexapod designs and explore a large design-space in finite element software packages is, in general, time consuming and inefficient. The purpose of this project was to develop software tools that made design-space exploration (modeling and simulation processes) for hexapod structures drastically more efficient. Secondly, the project included an experimental analysis portion to demonstrate the various modal study techniques and to validate finite element analysis predictions. Lastly, …

Solar Decathlon Controls, James Mitchel Routh, Travis Lathrop, Colby Jarrett, Zach Cross

Chancellor’s Honors Program Projects

No abstract provided.

Team Tennessee Solar Decathlon Hvac System, Susan Katherine Reid, Kevin Kelly, Brad Hight, Sam Felton

Chancellor’s Honors Program Projects

No abstract provided.

Design And Calibration Of A Wind Tunnel Facility For The Study Of Active Flow Control On Wind Turbine Blades, Christopher Paul Walter

Honors Capstone Projects - All

Our group at Syracuse University has been working under Professor Mark Glauser as part of a wind consortium with the University of Minnesota and United Technologies Research Group. Our component of this project will be to develop a system which can be imbedded in an airfoil which can increase the efficiency of the airfoil. Along with developing this “intelligent blade,” we will also be characterizing the affect our control system will have on aerodynamic noise. To accomplish these goals, Syracuse University’s anechoic jet facility was remodeled to incorporate a wind tunnel within which we could run our experiments. Upon the …

Simulation And Validation Of Two-Component Flow In A Void Recirculation System, Oscar Eduardo Daza

Master's Theses

Nuclear power plants rely on the Emergency Core Cooling System (ECCS) to cool down the reactor core in case of an accident. Occasionally, air is entrained into the suction piping of ECCS causing voids that decrease pumping efficiency, and consequently damage the pumps. In an attempt to minimize the amount of voids entering the suction side of the pump in ECCS, a Void Recirculation System (VRS) experiment was conducted for a proof of concept purpose. While many studies have been oriented in studying two-component flow behavior in ECCS, none of them propose a solution to minimize air entrainment. As a …

Finite Element Reconstruction Of Real World Aortic Injury In Near-Side Lateral Automotive Crashes With Conceptual Countermeasures, Aditya Neelakanta Belwadi

Wayne State University Dissertations

Traumatic rupture of the aorta (TRA) remains the second most common cause of death associated with motor vehicle crashes after brain injury. On an average, nearly 8,000 people die annually in the United States due to blunt injury to the aorta. It is observed that more than 80% of occupants who suffer an aortic injury die at the scene due to exsanguination into the chest. With the advent of more accurate and established human body finite element (FE) models, FE crash reconstruction methods may become a valuable tool when assessing crash scenarios and occupant injury mechanisms.

The current study is …

Physically Meaningful Harmonization Of Tire/Pavement Friction Measurement Devices, Madhura Priyanga Nishshanke Rajapakshe

USF Tampa Graduate Theses and Dissertations

Accurate characterization and evaluation of tire/pavement friction is critical in assuring runway and highway safety. Historically, Pavement Friction Measurement Devices (PFMDs) employing different measuring mechanisms have been used to evaluate tire/pavement friction. They yield significantly disparate friction coefficients under the same contact conditions. Currently, an empirically developed data harmonization method based on a reference device (Dynamic Friction Tester (DFT)) is used in an attempt to overcome the disparities between the measurements using various different PFMDs. However, this method, which has been standardized by the American Society for Testing and Materials (ASTM E1960), has been criticized for its inconsistency by researchers …