Engineering Commons^™

Lignin-Based Li-Ion Anode Materials Synthesized From Low-Cost Renewable Resources, Nicholas William Mcnutt

Doctoral Dissertations

In today’s world, the demand for novel methods of energy storage is increasing rapidly, particularly with the rise of portable electronic devices, electric vehicles, and the personal consumption and storage of solar energy. While other technologies have arguably improved at a rate that is exponential in accordance with Moore’s law, battery technology has lagged behind largely due to the difficulty in devising new electric storage systems that are simultaneously high performing, inexpensive, and safe.

In order to tackle these challenges, novel Li-ion battery anodes have been developed at Oak Ridge National Laboratory that are made from lignin, a low-cost, renewable …

Single Fiber Mechanical Properties Using Nano-Tensile Testing And Carbon Fiber Structure-Property Relationship, Matthew Erich Kant

Doctoral Dissertations

Single carbon fibers are studied using a nano-tensile testing system. This system has unprecedented load and displacement resolution, nN and nm respectively, and the ability to perform dynamic testing for storage and loss modulus during quasi-static tensile extension. Furthermore, improved fiber mounting and alignment procedures coupled with the precision of the nano-tensile testing system assist in unprecedented resolution in single fiber mechanical testing for axial modulus and strength. Hence, using these unique capabilities, the moduli and their statistical distribution of many high performance carbon fibers are reported here. From this, a simplified single parameter model describing the strain dependent modulus …

Mode I Fracture Toughness Of Eight-Harness-Satin Carbon Cloth Weaves For Co-Cured And Post-Bonded Laminates, Josh E. Smith

Master's Theses

Mode I interlaminar fracture of 3k 8-Harness-Satin Carbon cloth, with identical fill and weft yarns, pre-impregnated with Newport 307 resin was investigated through the DCB test (ASTM D5528). Crack propagations along both the fill and weft yarns were considered for both post-bonded (co-bonded) and co-cured laminates. A patent-pending delamination insertion method was compared to the standard Teflon film option to assess its applicability to mode I fracture testing. The Modified Beam Theory, Compliance Calibration method, and Modified Compliance Calibration method were used for comparative purposes for these investigations and to evaluate the validity of the proposed Equivalent Stiffness (EQS) method. …

Evaluation Of The Transient Thermal Performance Of A Graphite Foam/Phase Change Material Composite, Michael Paul Trammell

Masters Theses

The thermal transient response of graphite foam infiltrated with paraffin wax as a thermal protection composite was investigated. Graphite foam is a rigid open-celled porous carbon material that exhibits high thermal conductivity along the ligaments. To increase the ability of graphite foam to store heat energy, it was infiltrated with a phase change material, paraffin wax. Filling the foam with a phase change material (PCM) creates a composite that transfers heat through an interconnected network of ligaments to a large surface area of PCM for absorption. Foams were made at various pressures to understand the effect of porosity, which also …

Wolfpack Gear Inc. Composite Frame Firefighter Backpack, Gabriel Mountjoy, Blair Ridings, Carl Drummond Buchenroth

Mechanical Engineering

No abstract provided.

Kinetics Of Laser Chemical Vapor Deposition Of Carbon And Refractory Metals, Feng Gao

Doctoral Dissertations

Three-dimensional laser chemical vapor deposition (3D-LCVD) has been used to grow rods of carbon, tungsten, titanium, and hafnium from a variety of hydrocarbons and metal halide-based precursors. A novel computerized 3D-LCVD system was designed and successfully used in the experiments. A focused Nd:Yag laser beam (λ = 1.06 μm) was utilized to locally heat up a substrate to deposition temperature. The rods, which grew along the axis of the laser beam, had a typical diameter of 30–80 μm and a length of about 1 mm. The precursors for carbon deposition were the alkynes: propyne, butyne, pentyne, hexyne, and octyne. Propyne …

An Isothermal Study Of An S.A.E. 6150 Steel, Tom Liss, C. Arentzen

Bachelors Theses and Reports, 1928 - 1970

The purpose of this thesis is to set forth the method followed, the laboratory procedure practiced, the results obtained, the conclu­sions drawn, and the recommendations proposed as a consequence of a metallographic study of the isothermal transformation of an S.A.E. 6150 steel.

The Casting Of Anodes For The Series System Of Electrolytic Copper Refining, Robert R. Kupfer

Bachelors Theses and Reports, 1928 - 1970

The electrolytic refining process, while usually considered an auxiliary process used in conjunction with pyrometallurgical extraction, deserves a special niche in the complex metallurgy of copper. The development of electrolytic copper refining, for example, is largely responsible for the prominence of the electrical industry. Conversely, it could be stated that the electrical industry played an important part in the development of the copper industry.

Chromizing Of Steels, Edward Buchanan

Bachelors Theses and Reports, 1928 - 1970

In recent years, considerable thought and study have been given to the use of chromized articles in place of chromium stainless steel articles. The present extensive application of chromizing, indeed, helps greatly to conserve this valuable metal.

An Investigation Of A Particular Weldment Failure, Byron Clow

Bachelors Theses and Reports, 1928 - 1970

Two sets of weld-test coupons, supposedly made under identical conditions, were submitted to this institution last year for approval and certification under the A.S.M.E. Welder's Qualification Code. The first set of coupons was unsatisfactory. The second set, made by the same operators one month later, was satisfactory.

The Leaching Of Electrodeposition Of Iron, Emmett G. Simmons

Bachelors Theses and Reports, 1928 - 1970

Electrolytic iron as deposited is brittle and therefore must be annealed. After annealing, the material is ductile and closely resembles copper in its behavior under work. It is claimed to be more resistant to corrosion than dead soft iron. It also has the advantage of corroding uniformly ( or­dinary soft iron develops pin holes which shorten its life considerably).

The extreme purity of electrolytic iron namely makes it very suitable as a base metal for alloys. Its ductility opens up a field for use in the manufacture of cold rolled strip, seamless tubes, and wire.