Engineering Commons^™

Impact Of E20 Fuel On A High-Performance, Two-Stroke Engine, Jon Gregory Loesche

Dissertations, Master's Theses and Master's Reports

The purpose of this project was to explore the emissions, combustion, and performance effects of running a gasoline/ethanol fuel mixture of 20 percent by volume (E20) in a fuel-injected, two-stroke engine. The engine was operated at five engine speeds that corresponded with the EPA 5-mode emissions test for snowmobile engines. Single parameter sweeps were conducted along with a preliminary recalibration of the test engine at two E0 target values (lambda and mid-pipe temperature) using E20 fuel.

Baseline testing showed that running E20 fuel produced a leaner air/fuel mixture compared to E0, resulting in higher lambda values for all modes and …

Frontal Crash Analysis Of A Conformable Cng Tank Using Finite Element Analysis, Datta Sandesh Manjunath

Dissertations, Master's Theses and Master's Reports

The purpose of this study is to computationally model and analyze a Conformable Compressed Natural Gas (CNG) fuel tank for frontal crashes using Finite Element Analysis. Researchers have developed a CNG fuel tank, which is conformable, non-conventional and non-cylindrical. This tank increases cost efficiency, volumetric efficiency and cargo efficiency in CNG vehicle applications. A lightweight pickup truck (2015 Chevrolet Silverado) has been used to integrate the CNG tanks and field-testing has been conducted to demonstrate the application.

The report mainly focuses on the effective finite element modeling of the chassis, brackets and tanks using HYPERMESH and RADIOSS. The frontal crash …

Minimizing Run Time Of Finite Element Analyses: Applications In Conformable Cng Tank Modeling, Paul M. Roehm

Dissertations, Master's Theses and Master's Reports

REL Inc. has proposed a CNG tank that deviates from typical cylindrical storage methods. The goal of REL working with Michigan Tech is to minimize mass and meet NGV2 safety standards for pressure and drop testing for this tank.

The model has undulated outer surfaces and Schwarz P-surface internal geometry. To accurately mesh this, a small element size is necessary; this creates a model with millions of elements. In explicit analyses, this requires a large amount of computational resources to run.

This report focuses on methods to reduce model run time without reducing accuracy. Methods covered include creating symmetric building …

Advanced Uses For Carbon Nanotubes: A Spherical Sound Source And Hot-Films As Microphones, Micaela M. Thiery

Dissertations, Master's Theses and Master's Reports

Super-aligned carbon nanotube (CNT) thin-film is used to create thermophones. The thermal properties of CNT film allow it to rapidly heat and cool when supplied AC power producing temperature and pressure gradients and, therefore, audible sound. The advantages of CNT thermophones include eliminating all moving components of traditional speakers and reducing the weight of the speaker itself by using CNT film, which is nearly weightless. Additionally, the flexibility of CNT film provides the unique opportunity to construct loudspeakers of various sizes and geometries. In this work, a spherical CNT thermophone is designed, manufactured, and tested for directivity with the overall …

Control Of A Powered Ankle-Foot Prosthesis: From Perception To Impedance Modulation, Guilherme Aramizo Ribeiro

Dissertations, Master's Theses and Master's Reports

Active ankle prostheses controllers are demonstrating gaining smart features to improve the safety and comfort offor users. The perception of user intention to modulate the ankle dynamics is a well-known example of such feature. But not much work focused on the perception of the environment, nor how the environment should be included in the mechanical design and control of the prosthesisprostheses. The proposed work aims to improve the feasibility of integrate the environment perception integration intoto the prostheses controllersler, and to define the desired ankle dynamics, as mechanical impedance, duringof the human walk on different environmental settings. As a preliminary …

Development Of A High-Fidelity Model And Kalman Filter Based State Estimator For Simulation And Control Of Nox Reduction Performance Of A Scr Catalyst On A Dpf, Venkata Rajesh Chundru

Dissertations, Master's Theses and Master's Reports

Reduction of emissions and improving the fuel consumption are two prime research areas in Diesel engine development. The present after-treatment systems being used for emissions control include diesel oxidation catalyst (DOC) for NO, HC and CO oxidation along with catalyzed particulate filters for PM (particulate matter) and selective catalytic reduction (SCR) for controlling NOx emissions. Recently an after-treatment system called SCR catalyst on a DPF capable of simultaneously reducing both NOx and PM emissions has been developed in order to reduce the overall size of the after-treatment system.

The goal of this proposed research is to create a state estimator …

Simulation Of Human Ankle Trajectory During Stance Phase Of Gait, Leslie Castelino

Dissertations, Master's Theses and Master's Reports

A simulation was developed which mimics the human gait characteristics based on the input of an individual’s gait trajectory. This simulation also estimates the impedance of the human ankle based on the ground reaction forces measured by the force plate. This simulation will accept alterations of the following parameters: total body weight, weight of the shank, weight of the foot, trajectories of the shank and foot of the individual and orientation of the force plate, which would generate a new gait trajectory for the ankle during the stance phase of gait. The goal of this simulation was to validate the …

Using Lower Extremity Muscle Activations To Estimate Human Ankle Impedance In The External-Internal Direction, Lauren N. Knop

Dissertations, Master's Theses and Master's Reports

For millions of people, mobility has been afflicted by lower limb amputation. Lower extremity prostheses have been used to improve the mobility of an amputee; however, they often require additional compensation from other joints and do not allow for natural maneuverability. To improve upon the functionality of ankle-foot prostheses, it is necessary to understand the role of different muscle activations in the modulation of mechanical impedance of a healthy human ankle. This report presents the results of using artificial neural networks (ANN) to determine the functional relationship between lower extremity electromyography (EMG) signals and ankle impedance in the transverse plane. …

Multi-Modal And Short-Range Transmission Loss In Ice-Covered, Near-Shore Arctic Waters, Miles B. Penhale

Dissertations, Master's Theses and Master's Reports

In the past century, extensive research has been done regarding the sound propagation in arctic ice sheets. The majority of this research has focused on low frequency propagation over long distances. One of the most commonly used excitation methods for air-ice-water layers has been explosives. However, environmental regulation has become more stringent, disallowing the use of almost all explosive excitation types. Due to changing climate conditions in these environments, new experimentation is warranted to determine sound propagation characteristics in, through, and under thin ice sheets, in shallow water, over short distances. In April, 2016 several experiments were conducted approximately 2 …

Effect Of Spark Advance And Fuel On Knocking Tendency Of Spark Ignited Engine, Abhay S. Joshi

Dissertations, Master's Theses and Master's Reports

Knock, in spark ignition engine is the combustion caused by the autoignition of the fuel-air mixture. It is the phenomenon that limits engine performance and thermal efficiency. Knock also has an adverse effect on emissions and fuel economy. Engine designers target engines with maximum power and torque output without compromising on fuel economy. Engine downsizing is the method generally adopted. The main goal of engine downsizing is to achieve better fuel economy while increasing the power and torque output of the engine. Better fuel economy is achieved by reducing the displaced volume which in turn means a much higher brake …