Engineering Commons^™

Phase Transformation And Magnetic Properties Of Rapidly Solidified Mn-Al-C Alloys Modified With Zr, Yunlong Geng, Micheal J. Lucis, Pamela Rasmussen, Jeffrey E. Shield

Department of Mechanical and Materials Engineering: Faculty Publications

Mn_54-xAl₄₃C₃Zr_x (x=1, 3) alloys were prepared by rapid solidification followed by heat treatment to produce the ferromagnetic s phase. The substitution of Zr for Mn in the structure resulted in an increase of the saturation magnetization (Ms) compared to that of Mn_54-xAl₄₃C₃. While the highest Ms (12861 emu/g) was obtained in Mn_54-xAl₄₃C₃Zr₁, the coercivity was also improved to 1.62 kOe, compared to 1.25 kOe for Mn_54-xAl₄₃C₃. To further improve the coercivity through grain …

Extracting Continuum-Like Deformation And Stress From Molecular Dynamics Simulations, Lili Zhang, John Jasa, George Gazonas, Antoine Jerusalem, Mehrdad Negahban

Department of Mechanical and Materials Engineering: Faculty Publications

We present methods that use results from molecular dynamics (MD) simulations to construct continuum parameters, such as deformation gradient and Cauchy stress, from all or any part of an MD system. These parameters are based on the idea of minimizing the difference between MD measures for deformation and traction and their continuum counterparts. The procedures should be applicable to non-equilibrium and inhomogeneous systems, and to any part of a system, such as a polymer chain. The resulting procedures provide methods to obtain first and higher order deformation gradients associated with any subset of the MD system, and associated expressions for …

Evaluation Of Peritoneal Microbubble Oxygenation Therapy In A Rabbit Model Of Hypoxemia, Nathan D. Legband, Jameel A. Feshitan, Mark A. Borden, Benjamin S. Terry

Department of Mechanical and Materials Engineering: Faculty Publications

Alternative extrapulmonary oxygenation technologies are needed to treat patients suffering from severe hypoxemia refractory to mechanical ventilation. We previously demonstrated that peritoneal microbubble oxygenation (PMO), in which phospholipid-coated oxygen microbubbles (OMBs) are delivered into the peritoneal cavity, can successfully oxygenate rats suffering from a right pneumothorax. This study addressed the need to scale up the procedure to a larger animal with a splanchnic cardiac output similar to humans. Our results show that PMO therapy can double the survival time of rabbits experiencing complete tracheal occlusion from6.6 ± 0.6 min for the saline controls to 12.2 ± 3.0 min for the …

Electronic Structure Evolution Of Fullerene On Ch3Nh3Pbi3, Chenggong Wang, Congcong Wang, Xiaoliang Liu, John Kauppi, Yuchuan Shao, Zhengguo Xiao, Cheng Bi, Jinsong Huang, Yongli Gao

Department of Mechanical and Materials Engineering: Faculty Publications

The thickness dependence of fullerene on CH₃NH₃PbI₃ perovskite film surface has been investigated by using ultraviolet photoemission spectroscopy (UPS), X-ray photoemission spectroscopy (XPS), and inverse photoemission spectroscopy (IPES). The lowest unoccupied molecular orbital and highest occupied molecular orbital (HOMO) can be observed directly with IPES and UPS. It is observed that the HOMO level in fullerene shifts to lower binding energy. The XPS results show a strong initial shift of core levels to lower binding energy in the perovskite, which indicates that electrons transfer from the perovskite film to fullerene molecules. Further deposition of fullerene …

Improving The Sensitivity Of A Near-Infrared Nanocomposite Photodetector By Enhancing Trap Induced Hole Injection, Liang Shen, Yanjun Fang, Qingfeng Dong, Zhengguo Xiao, Jinsong Huang

Department of Mechanical and Materials Engineering: Faculty Publications

We report the enhancement of the photoconductive gain of nanocomposite near-infrared photodetectors by a zinc oxide nanoparticles (ZnO NPs) rich surface at the nanocomposite/cathode interface. An argon plasma etching process was used to remove polymer at the surface of nanocomposite films, which resulted in a ZnO NPs rich surface. The other way is to spin-coat a thin layer of ZnO NPs onto the nanocomposite layer. The ZnO NPs rich surface, which acts as electron traps to induce secondary hole injection under reverse bias, increased hole injection, and thus the external quantum efficiency by 2–3 times. The darkcurrent declined one order …

Efficiency Enhancement In Polymer Solar Cells With A Polar Small Molecule Both At Interface And In The Bulk Heterojunction Layer, Zhengguo Xiao, Qingfeng Dong, Qi Wang, Wenjing Tian, Hui Huang, Jinsong Huang

Department of Mechanical and Materials Engineering: Faculty Publications

The polar molecules, including ferroelectric materials with large dipole moments, have been applied as interfacial layers to increase the efficiency of organic solar cells by increasing the bounded charge separation, tuning the energy levels, etc. Here, we report a small polar molecule 2-cyano-3- (4-(diphenylamino) phenyl)acrylic acid (TPACA) that can be either blended in the active layer or at the polymer/electrode interface to increase the efficiency of organic solar cell devices after poling. It is found that the built-in potential of the device is increased by 0.2 V after poling under negative bias. Blending TPACA into the active layer has shown …

Chloride Incorporation Process In Ch3Nh3Pbi3-XClX Perovskites Via Nanoscale Bandgap Maps, Jungseok Chae, Qingfeng Dong, Jinsong Huang, Andrea Centrone

Department of Mechanical and Materials Engineering: Faculty Publications

CH₃NH₃PbI_3-xCl_x perovskites enable fabrication of highly efficient solar cells. Chloride ions benefit the morphology, carrier diffusion length and stability of perovskite films; however, whether those benefits stem from the presence of Cl⁻ in the precursor solution or from their incorporation in annealed films is debated. In this work, the photothermal induced resonance (PTIR), an in situ technique with nanoscale resolution, is leveraged to measure the bandgap of CH₃NH₃PbI_3-xCl_x films obtained by a multicycle coating process that produces high efficiency (≈16 %) solar cells. Because chloride …

Electron-Hole Diffusion Lengths >175 Μm In Solution-Grown Ch3Nh3Pbi3 Single Crystals, Qingfeng Dong, Yanjun Fang, Yuchuan Shao, Padhraic Mulligan, Jie Qiu, Lei Cao, Jinsong Huang

Department of Mechanical and Materials Engineering: Faculty Publications

Long, balanced electron and hole diffusion lengths greater than 100 nanometers in polycrystalline CH₃NH₃PbI₃ are critical for highly efficient perovskite solar cells. We report that the diffusion lengths in CH₃NH₃PbI₃ single crystals grown by a solution-growth method can exceed 175 μm under 1 sun illumination and exceed 3 mm under weak light for both electrons and holes. The internal quantum efficiencies approach 100% in 3 mm-thick single crystal perovskite solar cells under weak light. These long diffusion lengths result from greater carrier mobility, lifetime and dramatically smaller trap densities in …

Relevance Of Blood Vessel Networks In Blast-Induced Traumatic Brain Injury, Yi Hua, Shengmao Lin, Linxia Gu

Department of Mechanical and Materials Engineering: Faculty Publications

Cerebral vasculature is a complex network that circulates blood through the brain. However, the role of this networking effect in brain dynamics has seldom been inspected. This work is to study the effects of blood vessel networks on dynamic responses of the brain under blast loading. Voronoi tessellations were implemented to represent the network of blood vessels in the brain. The brain dynamics in terms of maximumprincipal strain (MPS), shear strain (SS), and intracranial pressure (ICP) weremonitored and compared. Results show that blood vessel networks significantly affected brain responses.The increased MPS and SS were observed within the brain embedded with …

Role Of Interphase In The Mechanical Behavior Of Silica/Epoxy Resin Nanocomposites, Yi Hua, Linxia Gu, Sundaralingam Premaraj, Xiaodong Zhang

Department of Mechanical and Materials Engineering: Faculty Publications

A nanoscale representative volume element has been developed to investigate the effect of interphase geometry and property on the mechanical behavior of silica/epoxy resin nanocomposites. The role of interphase–matrix bonding was also examined. Results suggested that interphase modulus and interfacial bonding conditions had significant influence on the effective stiffness of nanocomposites, while its sensitivities with respect to both the thickness and the gradient property of the interphase was minimal. The stiffer interphase demonstrated a higher load-sharing capacity, which also increased the stress distribution uniformity within the resin nanocomposites. Under the condition of imperfect interfacial bonding, the effective stiffness of nanocomposites …

Towards Tuning The Mechanical Properties Of Three-Dimensional Collagen Scaffolds Using A Coupled Fiber-Matrix Model, Shengmao Lin, Lauren A. Hapach, Cynthia Reinhart-King, Linxia Gu

Department of Mechanical and Materials Engineering: Faculty Publications

Scaffold mechanical properties are essential in regulating the microenvironment of three-dimensional cell culture. A coupled fiber-matrix numerical model was developed in this work for predicting the mechanical response of collagen scaffolds subjected to various levels of non-enzymatic glycation and collagen concentrations. The scaffold was simulated by a Voronoi network embedded in a matrix. The computational model was validated using published experimental data. Results indicate that both non-enzymatic glycation-induced matrix stiffening and fiber network density, as regulated by collagen concentration, influence scaffold behavior. The heterogeneous stress patterns of the scaffold were induced by the interfacial mechanics between the collagen fiber network …

In Situ Longitudinal Pre-Stretch In The Human Femoropopliteal Artery, Alexey Kamenskiy, Andreas Seas, Grant Bowen, Paul Deegan, Anastasia Desyatova, Nick Bohlim, William Poulson, Jason N. Mactaggart

Department of Mechanical and Materials Engineering: Faculty Publications

In situ longitudinal (axial) pre-stretch (LPS) plays a fundamental role in the mechanics of the femoropopliteal artery (FPA). It conserves energy during pulsation and prevents buckling of the artery during limb movement. We investigated how LPS is affected by demographics and risk factors, and how these patient characteristics associate with the structural and physiologic features of the FPA. LPS was measured in n=148 fresh human FPAs (14–80 years old). Mechanical properties were characterized with biaxial extension and histopathological characteristics were quantified with Verhoeff-Van Gieson Staining. Constitutive modeling was used to calculate physiological stresses and stretches which were then analyzed …

Multiscale Modeling Of Skeletal Muscle Active Contraction In Relation To Mechanochemical Coupling Of Molecular Motors, Jiangcheng Chen, Xiaodong Zhang, Shengmao Lin, He Wang, Linxia Gu

Department of Mechanical and Materials Engineering: Faculty Publications

In this work, a mathematical model was developed to relate the mechanochemical characterizations of molecular motors with the macroscopic manifestation of muscle contraction. Non-equilibrium statistical mechanics were used to study the collective behavior of myosin molecular motors in terms of the complex conformation change and multiple chemical states in one working cycle. The stochastic evolution of molecular motor probability density distribution during the contraction of sarcomere was characterized by the Fokker-Planck Equation. Quick muscle contraction was demonstrated by the collective dynamic behavior of myosin motors, the muscle contraction force, and the muscle contraction velocity-force relation. Our results are validated against …

Color And Texture Morphing With Colloids On Multilayered Surfaces, Ziguang Chen, Shumin Li, Andrew Arkebauer, George Gogos, Li Tan

Department of Mechanical and Materials Engineering: Faculty Publications

Dynamic morphing of marine species to match with environment changes in color and texture is an advanced means for surviving, self-defense, and reproduction. Here we use colloids that are placed inside a multilayered structure to demonstrate color and texture morphing. The multilayer is composed of a thermal insulating base layer, a light absorbing mid layer, and a liquid top layer. When external light of moderate intensity (∼0.2 W cm−2) strikes the structure, colloids inside the liquid layer will be assembled to locations with an optimal absorption. When this system is exposed to continuous laser pulses, more than 18 000 times …

Inducing Persistent Flow Disturbances Accelerates Atherogenesis And Promotes Thin Cap Fibroatheroma Development In D374y-Pcsk9 Hypercholesterolemic Minipigs, Ryan M. Pedrigi, Christian Bo Poulsen, Vikram V. Mehta, Niels Ramsing Holm, Nilesh Pareek, Anouk L. Post, Ismail Dogu Kilic, Winston A.S. Banya, Gianni Dall'ara, Alessio Mattesini, Martin M. Bjorklund, Niels P. Andersen, Anna K. Grondal, Enrico Petretto, Nicolas Foin, Justin E. Davies, Carlo Di Mario, Jacob Fog Bentzon, Hans Erik Botker, Erling Falk, Rob Krams, Ranil De Silva

Department of Mechanical and Materials Engineering: Faculty Publications

Background—Although disturbed flow is thought to play a central role in the development of advanced coronary atherosclerotic plaques, no causal relationship has been established. We evaluated whether inducing disturbed flow would cause the development of advanced coronary plaques, including thin cap fibroatheroma (TCFA).

Methods and Results—D374Y-PCSK9 hypercholesterolemic minipigs (N=5) were instrumented with an intracoronary shear-modifying stent (SMS). Frequency-domain optical coherence tomography was obtained at baseline, immediately post-stent, 19, and 34 weeks and used to compute shear stress metrics of disturbed flow. At 34 weeks, plaque type was assessed within serially-collected histological sections and co-registered to …

Quantification Of Plaque Stiffness By Brillouin Microscopy In Experimental Thin Cap Fibroatheroma, Giuseppe Antonacci, Ryan M. Pedrigi, Avinash Kondiboyina, Vikram V. Mehta, Ranil De Silva, Carl Paterson, Rob Krams, Peter Torok

Department of Mechanical and Materials Engineering: Faculty Publications

Plaques vulnerable to rupture are characterized by a thin and stiff fibrous cap overlaying a soft lipid-rich necrotic core. The ability to measure local plaque stiffness directly to quantify plaque stress and predict rupture potential would be very attractive, but no current technology does so. This study seeks to validate the use of Brillouin microscopy to measure the Brillouin frequency shift, which is related to stiffness, within vulnerable plaques. The left carotid artery of an ApoE^-/- mouse was instrumented with a cuff that induced vulnerable plaque development in nine weeks. Adjacent histological sections from the instrumented and control arteries …

Mammalian Synthetic Biology: Emerging Medical Applications, Zoltan Kis, Hugo Sant'ann Pereira, Takayuki Homma, Ryan M. Pedrigi, Rob Krams

Department of Mechanical and Materials Engineering: Faculty Publications

In this review, we discuss new emerging medical applications of the rapidly evolving field of mammalian synthetic biology.We start with simple mammalian synthetic biological components and move towards more complex and therapy-oriented gene circuits. A comprehensive list of ON–OFF switches, categorized into transcriptional, post-transcriptional, translational and posttranslational, is presented in the first sections. Subsequently, Boolean logic gates, synthetic mammalian oscillators and toggle switches will be described. Several synthetic gene networks are further reviewed in the medical applications section, including cancer therapy gene circuits, immuno-regulatory networks, among others. The final sections focus on the applicability of synthetic gene networks to drug …

Quantification Of Ultraprecision Surface Morphology Using An Algebraic Graph Theoretic Approach, Prahalad Rao, Satish T. S. Bukkapatnam, Zhenyu (James) Kong, Omer F. Beyca, Kenneth Case, Ranga Komanduri

Department of Mechanical and Materials Engineering: Faculty Publications

Assessment of progressive, nano-scale variation of surface morphology during ultraprecision manufacturing processes, such as fine-abrasive polishing of semiconductor wafers, is a challenging proposition owing to limitations with traditional surface quantifiers. We present an algebraic graph theoretic approach that uses graph topological invariants for quantification of ultraprecision surface morphology. The graph theoretic approach captures heterogeneous multi-scaled aspects of surface morphology from optical micrographs, and is therefore valuable for in situ real-time assessment of surface quality. Extensive experimental investigations with specular finished (Sa ~ 5 nm) blanket copper wafers from a chemical mechanical planarization (CMP) process suggest that the proposed method was …

Asphalt Composition, David Allen, Flavio Souza, Yong-Rak Kim, Roberto Soares

Department of Mechanical and Materials Engineering: Faculty Publications

A computational method is provided for predicting roadway failure due to degradation of the roadway over time as a function of the input loads, the roadway geometry, the material properties of the constituents in the asphaltic pavement, the shape, distribution, orientation and volume fractions of the constituents, and environmental conditions. The unique and new feature of the method is that it employs several physically based predictive methodologies simultaneously.

Size Effects In Human Visual Inspection For Micro/Meso Scale Parts, Sri Harsha Kavuri

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

Visual inspection has been a major method of quality control in conventional manufacturing processes for the last fifty years. Utilizing trained human inspectors to perform this visual inspection has been the most effective means of maintaining quality control. Extensive research has been performed to understand the factors that influence the human inspection process.

In the recent years, there has been a significant emphasis on manufacturing at the smaller end of the size-spectrum such as Micro and Meso scale manufacturing. Quality control at becomes a challenging task due to the extremely small sizes. Several automated visual inspection techniques have been proposed …

Influence Of Spatial Variations Of Railroad Track Stiffness And Material Inclusions On Fatigue Life, Celestin Nkundineza

Department of Mechanical and Materials Engineering: Dissertations, Theses, and Student Research

Railroad transportation is very important for economic growth and effective maintenance is one critical factor for its economic sustainability. The high repetitive forces from a moving railcar induce cyclic stresses that lead to rail bending and potential deterioration due to fatigue crack initiation and propagation. Previous research for prediction of fatigue life has been done under the assumptions of a uniform track bed and a homogeneous rail. However the spatial variation of the track stiffness is expected to increase the maximum stresses in the rail and, therefore, accelerate the fatigue process. The research described in this dissertation is focused on …