Engineering Commons^™

Efficiency Testing Of An Electronic Speed Controller, Grace Cowell, Matthew Hudson, Marcus Pereira

Mechanical Engineering

This project required the development of a rig that could experimentally determine the efficiency of an Electronic Speed Controller (ESC). The selected design focuses on measuring the losses due to heat from the device and comparing this to its input power. The selected design is a flow rig that utilizes the heat equation q=ṁcpΔT. The rig provides a steady state measurement of the ESC heat output by passing a known mass flow rate of air across the ESC and measuring the temperature difference. It uses a flowmeter to determine ṁ, thermocouples to determine ΔT, and a table lookup to determine …

Magnetic Bearing For Bently Nevada Rk4 Rotor Kits, Sean Fowler, Garrett Olson

Mechanical Engineering

Active Magnetic Bearings (AMB) are contact free bearings that support loads by magnetic levitation. This is accomplished by generating magnetic forces with electric current through a series of electromagnets surrounding a suspended rotor mass. Along with a set of electromagnets, an AMB assembly also consists of power amplifiers for each electromagnet, a controller, and proximity sensors. The proximity sensors provide rotor position feedback to the control system, which modulates power to the amplifiers [4]. Magnetic bearings are used in several industrial applications today, including but not limited to compressors, turbines, pumps, motors, and generators. Advantages of their utility include very …

Metals Am Design For Manufacturing, Maren Cosens, Ben Wong, Kevin Hale

Mechanical Engineering

We are looking to improve upon the current post processing techniques for metal additive manufacturing (AM). This project, sponsored by Lawrence Livermore National Laboratory (LLNL), will investigate ways to improve the design of stainless steel 316 parts made by AM, and how these designs will help with post processing techniques. We hope that the findings regarding stainless steel will apply to to improve the AM and post processing handshake in general. In particular, the project will focus on including different features in different basic part design shapes to aid in fixturing and post-processing of the part made by AM. This …

Compliant Air Skates, An Experiment, Samuel Feldtkeller, Cody Anderson, Kevin Daily, Eliana Stefani

Mechanical Engineering

There is currently a gap in the market of train levitation systems: wheeled trains and MagLev trains exist, but none utilize the low friction and high efficiency aspect of trains levitated by air skates. An air skate, is an air bearing that uses a pressure difference along its annular body to create a thin flow of air which is strong enough to "levitate" the weight of the skate. We have designed a compliant air skate that can glide over 0.04[in] defects in surfaces without touching down. After having made compliant skirts out of fiberglass and silicone, our setup of three …

Low Cost Metal Chip Separator, Alek Linquist, Kale Mckinney, Ryan Jones

Mechanical Engineering

We were tasked by Micro-Vu to design, build, and test a small-scale low-cost metal chip separator to operate on one of their 24/7 mills. The goal of the project was to separate the steel and aluminum chips coming off of the mill’s chip conveyor to end up with a bin of 99% pure aluminum by mass. To accomplish this goal we first brainstormed various possible ideas and performed small scale tests the best ones. After further review we determined the best solution to this problem was a design that involved a cycling magnetic backing that would pull steel out of …

Metals Additive Manufacturing Powder Aging Characterization, Thomas Russell Lovejoy, Nicholas Karl Muetterties, David Takeo Otsu

Mechanical Engineering

The metallic additive manufacturing process known as selective laser melting requires highly spherical, normally distributed powder with diameters in the range of 10 to 50 microns. Previous observations have shown a degradation in powder quality over time, resulting in unwanted characteristics in the final printed parts. 21-6-9 stainless steel powder was used to fabricate test parts, with leftover powder recycled back into the machine. Powder samples and test specimens were characterized to observe changes across build cycles. Few changes were observed in the physical and mechanical properties of the specimens, however, there were indications of chemical changes across cycles. Potential …

Disc Brake Energy Conversion, D. Coleman Badgley, Jeffrey W. Powell

Mechanical Engineering

The original goal of this project was to complete the design and building of a disc brake energy conversion project started by a former senior project team, and then spend a majority of the year performing testing in order to see if the device could be used to accurately calculate the Joule's constant. However, due to unforeseen complications and obstacles, the design and manufacturing portion of the project ended up taking much longer than anticipated. A majority of this time was spent designing the hydraulic plumbing system that would actuate the brakes. The previous team purchased some hydraulic parts and …

Inclusive Lectern, Trent Canales, Sean Day, Dylan Sigley, Stephen Sippel

Mechanical Engineering

A lectern is an essential piece of equipment for almost all speeches and presentations. They come in many forms and range in degree of professionalism depending on the occasion. Lecterns not only hold a presenter’s notes, a microphone, or other presentation aids, they provide a structure for a presenter that can bolster their confidence during a presentation. As such, it is important that all presenters have a lectern available to them. Unfortunately this is not always the case due to lectern accessibility limitations. This problem inspired the Cal Poly Disability Resource Center to request a lectern that satisfies the Least …

Solar Turbines Compressor Blade Installation Tools, Ryan Bruce, Carolyn Honeycutt, Stephen Oltrogge, Emmett Ross

Mechanical Engineering

The following report documents a California Polytechnic State University, Mechanical Engineering Senior Project sponsored by the gas turbine manufacturer, Solar Turbines. The senior project team consisted of four senior mechanical engineering students at Cal Poly, all with general concentrations; Ryan Bruce, Carolyn Honeycutt, Steve Oltrogge, and Emmett Ross. Kenneth Thomas sponsored the group and serves as the point of contact between the senior project team and Solar Turbines. He is a member of the Solar Turbines Mechanical Design Engineering Team and a Cal Poly graduate. Christoph Maurer served as the project team’s on-campus advisor.

A gas turbine uses internal combustion …

Ultra-Light Bear Canister, Naveen Beasley, Eli Rogers, Cory Wilson, Donald Wood

Mechanical Engineering

A bear canister is the primary tool used by outdoor enthusiasts to protect their food from bears while camping or backpacking. There are many effective products currently on the market, however many are not designed with reduced weight in mind. Hardcore backpackers want to have the lightest gear possible to ease the strain of carrying a large pack for sometimes weeks at a time.

Current bear canisters exist that utilize carbon fiber for weight reduction, however they rely on stock carbon tubes and lack engineering analysis, and no competitor has a fully composite bear canister available. Our sponsor, Nick Hellewell, …

Walker Tray, Marlene Troncoso, Judy Lantaca, Miriam Krage, Claire Francis

Mechanical Engineering

Sean is an individual with Cerebral Palsy, a disability that affects one's balance, muscle tone, muscular coordination, posture and control. Sean utilizes a walker to aid in maintaining his balance and muscular coordination when ambulating. This enables him to walk independently and leads to improved muscle strength and coordination. When walking, Sean places both hands on the walker to maintain balance and thus the ability to walk and carry items at the same time is compromised. Sean would like to be able to transport items while in use of his walker. The goals of this senior project design are to …

Non-Puncturing, No Slip Thv Leaflet Gripper, Brooks Kelly, Eric Nagaoka, Johnny Phane

Mechanical Engineering

Confidential

Universal Weight Machine, Oscar Andrade, Bibiana Koch, Robert Molloy, Haley Rentfro, Emily Woods

Mechanical Engineering

The purpose of this project is to design and build an inexpensive, universally accessible multi-station exercise machine for the physical and mental well-being of athletes of the Special Olympics and Pathpoint Life Education & Advancement Program. The machine has three sides tiered to higher resistance: the first station offers a minimal resistance aerobic exercise focused on moving the arms with an ergometer, the second station provides numerous locations to latch on resistance bands that will build strength in the athlete’s arms and chest, and the final station has a donated weight machine that offers lat pulldowns and flys with maximum …

Fluid Analysis In Solar Heat Pipes, Ben Krumholz, Michael Agavo, William Dundon

Mechanical Engineering

Evacuated tube solar collectors are efficient systems that use heat pipes to facilitate heat transfer. They use incoming solar radiation to heat water. Professor Mason Medizade tasked the team with choosing a component of the system to research and test its influence on system performance. The team investigated the working fluid that runs through the heat pipes. Distilled water, acetone, and ethanol at a range of fill volumes form 1 mL to 11 mL were tested. The team's goal was to find a volume for each fluid to maximize performance of the system. Performance was defined as average temperature rise …

Wind Tunnel Wheel Balance, Brady Hiob, Ryan Hamamura, Samuel Fleet

Mechanical Engineering

No abstract provided.

Electric Vehicle Torque Vectoring And Rear Steering Control System, Garrett Heinen, Vincent Lee, Michael Parker, Michael Saggese

Mechanical Engineering

NDA

Ancillary Attachment Methods, Creed Borden, Mickey Mackle, Thomas Tolley

Mechanical Engineering

No abstract provided.

High­Impact Textile Joining For Uav Landing Application: Tensile Testing Of Textiles, Patrick Michniuk, Matthew Ferretti, Jennifer Ford

Mechanical Engineering

The main objective of this project is to improve upon the current stitching pattern used in UAV catch net applications with the intention of lengthening their useable life cycle. To achieve this, a testing setup and procedure has been developed to produce material strength and stiffness data for nylon­ webbing strap, and for sewn intersections of the same strap material. The current stitching pattern was tested, and quantitatively characterized based on strength and stiffness. New stitching designs were generated and tested using the same procedure, and the results compared. This allowed for the selection of the most optimized stitching pattern …