Open Access. Powered by Scholars. Published by Universities.®
- Keyword
-
- 3D-print (1)
- 3d printing (1)
- AM tooling (1)
- Al2O3:C (1)
- Bead scaffold (1)
-
- BiW (1)
- CFRP (1)
- Cancer (1)
- Collagen Type I (1)
- Craft (1)
- Crochet (1)
- Form (1)
- HPRTM (1)
- High Entropy Oxide Pyrochlore Radiation Stability (1)
- LCA (1)
- Lacemaking (1)
- Light weighting (1)
- Luminescence (1)
- Lumpectomy (1)
- Material characterization (1)
- NanoDot (1)
- OSL (1)
- Optically stimulated luminescence (1)
- Osl (1)
- PLA (1)
- Plastic recycling (1)
- Polylactic acid (1)
- Primary colors (1)
- Recycling (1)
- Shape (1)
Articles 1 - 7 of 7
Full-Text Articles in Engineering
Radiation Exposure Calibration Of The Al2o3:C With Radium-226 And Cesium-137 Using The Osl Method, Selma Tepeli Aydin
Radiation Exposure Calibration Of The Al2o3:C With Radium-226 And Cesium-137 Using The Osl Method, Selma Tepeli Aydin
All Theses
Optically stimulated luminescence (OSL) dosimetry was utilized to calibrate Al2O3:C powder dosimeters, available commercially as the nanoDot® from Landauer Inc., and compare the dosimeter response to radium-226 (226Ra) and cesium-137 (137Cs). The signal from the OSL was quantified using a microSTARii® OSL reader also produced by Landauer Inc. Dose-response curves were developed for 226Ra and 137Cs experiments (5 dosimeters each) at thirteen absorbed doses. Individual dosimeter response was tracked by serial number. Linear regression analysis was performed to determine if there were significant differences between the intercepts of the …
Material World, Nicole Weldy
Material World, Nicole Weldy
All Theses
My thesis, Material World, delves into the use of the crochet unit as a construction technique for building forms. Through this, I aim to organize different materials in a way that responds to the challenges posed by the physical world. My artistic process is centered around honoring the inherent qualities of thread and uses these qualities to create form, lightness, and linearity. At the same time, I remain receptive to transformative processes such as combining three-dimensional (3D) printed lines and lace stiffener to push the boundaries of what thread can do. By combining manual craftsmanship with technology materialized as …
Temperature Gradient Effect On Solid-Liqid Interface Properties Of Al-Cu Alloy: A Molecular Dynamics Study, Prashant Kumar Jha
Temperature Gradient Effect On Solid-Liqid Interface Properties Of Al-Cu Alloy: A Molecular Dynamics Study, Prashant Kumar Jha
All Theses
Aluminum-copper (Al-Cu) alloys are widely used in the aerospace industry due to their favorable strength-to-weight ratio, good fatigue resistance, and corrosion resistance. These properties make Al-Cu alloys an excellent choice for aircraft structural components that require high strength and low weight. Additive manufacturing (AM), also known as 3D printing, has emerged as a promising processing method for Al-Cu alloys in aerospace manufacturing. AM enables the production of lightweight optimized geometries difficult to manufacture through conventional subtractive methods. AM also reduces material waste by only depositing material where needed in the part geometry. The rapid solidification conditions in AM processes motivate …
Life Cycle Energy Assesment Of Advanced Fiber Reinforced Composite Design And Manufacturing Methodologies, Urjit Lad
All Theses
Automotive industry at large is focused on vehicle light-weighting since a 6%-8% increase in fuel efficiency can be achieved with a 10% reduction in vehicle weight [1]. With the growing demand for cost-effective and sustainable light weighting of automobile structures, interest has increased in the application of fiber reinforced plastic (FRP) composites for use in the Body-in-White (BiW), which can account for up to 40% of the total vehicle weight. Traditional FRP composite manufacturing processes like vacuum assisted resin transfer molding, autoclave consolidation or use of automated fiber placement have been successfully used for marine and aerospace applications. However, these …
Characterization Of Mechanically Recycled Polylactic Acid (Pla) Filament For 3d-Printing By Evaluating Mechanical, Thermal, And Chemical Properties And Process Performance, Mahsa Shabani Samghabady
Characterization Of Mechanically Recycled Polylactic Acid (Pla) Filament For 3d-Printing By Evaluating Mechanical, Thermal, And Chemical Properties And Process Performance, Mahsa Shabani Samghabady
All Theses
Polylactic acid (PLA) is a biopolymer made from renewable resources such as sugar and corn. PLA filament is a popular material used in Fused Deposition Modeling (FDM) 3D-printing. While this material has many advantages, all the failed parts, support structures, rafts, nozzle tests, and the many prototype iterations during the 3D-printing process contribute to the plastic pollution and release of greenhouse gases. Although PLA is biodegradable, it can take years to degrade in landfills. Instead of throwing away PLA waste and buying new filaments, PLA can be recycled. Amongst the different recycling technologies, mechanical recycling is the most environmentally friendly. …
Preparation Of High Entropy Titanite Pyrochlore And Radiation Stability Study, Adam Gootgeld
Preparation Of High Entropy Titanite Pyrochlore And Radiation Stability Study, Adam Gootgeld
All Theses
Pyrochlore has been studied as a host phase for safe storage of radionuclides and exists naturally with long-term stability with good long-range order [1]. High entropy oxides show promising tunable properties that could demonstrate favorable bulk deposit of radioactive materials such as spent nuclear fuel (Uranium and other actinides). It is proposed that using high entropy oxides (HEOs) as the cation in this framework will shift the gibbs free energy so that radioactive nuclear waste will be stabilized for safe, long-term, eco-friendly storage. We have established a consistent method to fabricate high entropy titanite pyrochlores. In this study, ion beam …
An In Vivo Biocompatibility Analysis Of A Novel Tissue Regeneration Matrix Using A Pig Model, Shamar Thomas
An In Vivo Biocompatibility Analysis Of A Novel Tissue Regeneration Matrix Using A Pig Model, Shamar Thomas
All Theses
The goal of this project is to develop an injectable bead scaffold to promote tissue regeneration in the void created by lumpectomy and to alleviate post lumpectomy problems by preventing local recurrence and minimizing surgical-related infections. Microbeads were synthesized from collagen type I and crosslinked with tannic acid to form the basis for this injectable therapeutic. Tannic acid acts as a therapeutic anticancer agent. The action mechanisms of tannins in breast cancer cells have been studied with studies showing tannins to be cytotoxic to cancer cells in a dose-dependent manner. Tannic acid induces apoptosis in breast cancer cells via caspase …