Engineering Commons^™

Energy Localization And Heat Generation In Composite Energetic Systems Under High-Frequency Mechanical Excitation, Jesus O. Mares

Open Access Dissertations

In this work, the ability to use high frequency mechanical excitation to generate significant heating within plastic bonded explosives, as well as single energetic particles embedded within a viscoelastic binder, is studied. In this work, the fundamental mechanisms associated with the conversion of high-frequency mechanical excitation to heat as applied to these composite energetic systems are thoroughly investigated.

High-frequency contact excitation has been used to generate a significant amount of heat within samples of PBX 9501 and representative inert mock materials. Surface temperature rises on the order of 10 °C were observed at certain frequencies over a range from 50 …

Development Of Metal Matrix Composite Gridlines For Space Photovoltaics, Omar K. Abudayyeh

Chemical and Biological Engineering ETDs

Space vehicles today are primarily powered by multi-junction photovoltaic cells due to their high efficiency and high radiation hardness in the space environment. While multi-junction solar cells provide high efficiency, microcracks develop in the crystalline semiconductor due to a variety of reasons, including: growth defects, film stress due to lattice constant mismatch, and external mechanical stresses introduced during shipping, installation, and operation. These microcracks have the tendency to propagate through the different layers of the semiconductor reaching the metal gridlines of the cell, resulting in electrically isolated areas from the busbar region, ultimately lowering the power output of the cell …

Additive Manufacturing Of Carbon Fiber-Reinforced Thermoplastic Composites, Nicholas M. Denardo

Open Access Theses

Additive manufacturing, or 3D printing, encompasses manufacturing processes that construct a geometry by depositing or solidifying material only where it is needed in the absence of a mold. The ability to manufacture complex geometries on demand directly from a digital file, as well as the decreasing equipment costs due to increased competition in the market, have resulted in the AM industry experiencing rapid growth in the past decade. Many companies have emerged with novel technologies well suited to improve products and/or save costs in various industries.

Until recently, the applications of polymer additive manufacturing have been mainly limited to prototyping. …

Studies On The Electrical Transport Properties Of Carbon Nanotube Composites, Taylor Warren Tarlton

Doctoral Dissertations

This work presents a probabilistic approach to model the electrical transport properties of carbon nanotube composite materials. A pseudo-random generation method is presented with the ability to generate 3-D samples with a variety of different configurations. Periodic boundary conditions are employed in the directions perpendicular to transport to minimize edge effects. Simulations produce values for drift velocity, carrier mobility, and conductivity in samples that account for geometrical features resembling those found in the lab. All results show an excellent agreement to the well-known power law characteristic of percolation processes, which is used to compare across simulations. The effect of sample …

Finite Element Modeling Of Delamination Damage In Carbon Fiber Laminates Subject To Low-Velocity Impact And Comparison With Experimental Impact Tests Using Nondestructive Vibrothermography Evaluation, George Rodriguez Iv

Master's Theses

Carbon fiber reinforced composites are utilized in many design applications where high strength, low weight, and/or high stiffness are required. While composite materials can provide high strength and stiffness-to-weight ratios, they are also more complicated to analyze due to their inhomogeneous nature. One important failure mode of composite structures is delamination. This failure mode is common when composite laminates are subject to impact loading.

Various finite element methods for analyzing delamination exist. In this research, a modeling strategy based on contact tiebreak definitions in LS-DYNA^®was used. A finite element model of a low-velocity impact event was created to …

Damage Tolerance And Assessment Of Unidirectional Carbon Fiber Composites, Mark David Flores

Open Access Theses & Dissertations

Composites are beginning to be used in a variety of different applications throughout industry. However, certification and damage tolerance is a growing concern in many aerospace and marine applications. Although compression-after-impact have been studied thoroughly, determining a damage tolerance methodology that accurately characterizes the failure of composites has not been established. An experimental investigation was performed to study the effect of stacking sequence, low-velocity impact response, and residual strength due to compression and fatigue. Digital Image Correlation (DIC) captured the strains and deformation of the plate due to compression. Computational investigations integrated non-destructive techniques (C-Scan, X-Ray) to determine the extent …

Fabrication And Testing Of Cfrp Composites With Embedded Piezoelectric Particles For Temperature Sensing And Energy Harvesting, Emilio Tarango Valles

Open Access Theses & Dissertations

As a part of this world's continuous evolution and technological advancements, smart materials and functional composites have become an attractive topic. In many cases, these new functional composites are replacing the traditional engineering material due to their customizable mechanical properties. This Thesis analyzes and demonstrates the signal response, sensing capabilities and structural properties from Carbon/Glass Fiber Reinforced Plastic Composites (CFRP) with embedded Lead Zirconate Titanate Particles (PZT). The added PZT particles function as actuators, giving the composites a functionality. The PZT quantity inside each composite was variated to study better and characterize the mechanical and electrical properties; the variations were …