Open Access. Powered by Scholars. Published by Universities.®
Articles 1 - 5 of 5
Full-Text Articles in Engineering
Relationship Between Peel Force, Opening Force, And Burst Force For A Semi-Rigid Cup And Lid, Pre- And Post-Retort, Raj Navalakha
Relationship Between Peel Force, Opening Force, And Burst Force For A Semi-Rigid Cup And Lid, Pre- And Post-Retort, Raj Navalakha
All Theses
This research determines if there is any relationship between the peel force, the opening force and the burst force for a semi-rigid cup and lid system, for pre- and post-retort conditions. It also compares the relationship (regression lines) between these forces pre- and post-retort. These seal results were studied by varying the sealing parameters of dwell time and temperature while keeping the pressure constant. Polypropylene cups and a peelable barrier retort lidding were used in this study. As compared to past research, a different peel testing technique was used to measure the peel and the opening force. The entire lid …
Microanalysis Of Polymer Chain Diffusion In Heat Seals, Russell Cooper
Microanalysis Of Polymer Chain Diffusion In Heat Seals, Russell Cooper
All Theses
Heat sealing is an integral method for the closure and protection of packaging. Previous work has shown that seal strength is developed by the interdiffusion of polymer chains within heat seals. Heat seals were made between two dissimilar materials. Poly(ethylene-co-acrylic acid) (EAA) was heat sealed to ionomer. Diffusion within the EAA-ionomer heat seals was estimated. The diffusion estimates were then related to resulting seal strength in the EAA-ionomer sealant system. Heated tooling sealing was utilized to make heat seals at 40 psi (275.79 kPa), 0.5 seconds, and a range of temperatures between 180˚F (82.22˚C) and 300˚F (148.89˚C). Scanning electron microscopy …
Fabrication And Characterization Of Magnetic Nanoparticle Composite Membranes, Akeem Cruickshank
Fabrication And Characterization Of Magnetic Nanoparticle Composite Membranes, Akeem Cruickshank
All Theses
To effectively and accurately deliver drugs within the human body, both new designs and components for implantable micropumps are being studied. Designs must ensure high biocompatibility, drug compatibility, accuracy and small power consumption. The focus of this thesis was to fabricate a prototype magnetic nanoparticle membrane for eventual incorporation into a biomedical pump and then determine the relationship between this membrane deflection and applied pneumatic or magnetic force. The magnetic nanoparticle polymer composite (MNPC) membranes in this study were composed of crosslinked polydimethylsiloxane (PDMS) and iron oxide nanoparticles (IONPs). An optimal iron oxide fabrication route was identified and particle size …
Synthesis Of Silicon Carbide Fibers From Polycarbosilane By Electrospinning Method, Yuan Yue
Synthesis Of Silicon Carbide Fibers From Polycarbosilane By Electrospinning Method, Yuan Yue
All Theses
Silicon carbide (SiC) is widely used in many fields due to its unique properties. Bulk SiC normally has a flexural strength of 500 - 550 MPa, a Vickers hardness of ~27 GPa, a Young's modulus of 380 - 430 GPa, and a thermal conductivity of approximately 120 W/mK. SiC fibers are of great interest since they are the good candidates for reinforcing ceramic matrix composites (CMCs) because of the weavability and high temperature strength of about two to three GPa at about 1000 °C. Silicon carbide fibers have been synthesized from polycarbosilane (PCS) with ~25 μm diameter using the melt-spinning …
Inverse Problems Using Reduced Basis Method, Phil Gralla
Inverse Problems Using Reduced Basis Method, Phil Gralla
All Theses
Inverse Problems is a field of great interest for many applications, such as parameter identification and image reconstruction. The underlying models of inverse problems in many applications often involve Partial Differential Equations (PDEs). A Reduced Basis (RB) method for solving PDE based inverse problems is introduced in this thesis. The RB has been rigorously established as an efficient approach for solving PDEs in recent years. In this work, we investigate whether the RB method can be used as a regularization for solving ill-posed and nonlinear inverse problems using iterative methods. We rigorously analyze the RB method and prove convergence of …