Engineering Commons^™

Mimo Antenna For Fifth Generation Mm-Wave Applications: A Bibliometric Survey, Rajeshwari R. Malekar, Laxmikant K. Shevada, Hema D. Raut, Amruta S. Dixit, Sumit Kumar

Library Philosophy and Practice (e-journal)

Nowadays most discussed technology is mm-wave and 5G communication. The requirement of 5G technology is high bandwidth, high data rate, and low latency. To fulfil these requirements for the current growth in mobile communication multiple input multiple output antenna is used. This bibliometric paper throws light on the various methods used to improve mutual coupling between multiple antennas. Various mutual coupling reduction techniques that are used in MIMO antennas like Dielectric resonator antenna, Electromagnetic Bandgap Structure, Neutralization lines, Defected Ground Structures, Metamaterial, etc. are explained. Scopus database is used for this bibliometric review on mm-wave MIMO 5G technology from the …

A Bibliometric Survey On Ultra Wideband Multiple Input Multiple Output Antenna With Improved Isolation, Laxmikant K. Shevada, Hema D. Raut, Rajeshwari R. Malekar, Amruta S. Dixit, Sumit Kumar

Library Philosophy and Practice (e-journal)

Ultra wideband (UWB) technology remains a viable choice for very high speed data communication in future applications involving large bandwidth. For boosting the data communication efficiency and to mitigate the multipath fading issue faced by UWB system with existing narrowband systems, Multiple Input Multiple Output (MIMO) antenna system is used along with UWB. Mutual coupling which must be smaller in value plays a vital role in deciding the efficiency of MIMO antenna and hence it becomes as important aspect. The mutual coupling reduction techniques of various UWB MIMO antennas are surveyed in this bibliometric paper. The bibliometric survey aims to …

A Brief Bibliometric Survey On Circularly Polarized Antennas For Mobile Communication, Aniket Gunjal, Abhaya Pal Singh

Library Philosophy and Practice (e-journal)

This paper presents a database review on “Circularly Polarized Antennas for Mobile Communication” as it is the emerging technique used by mobile service provider because of having benefits over other types of antennas available.The polarization purity is now the major issue. In some cases due to cross polarization issue the antenna signal is cancelled at receiver side.So, it is necessary to have circularly polarized antenna to avoid this polarization issue because of change in phase of signal. The change in phase of signal is due to striking of wave on the obstacles and it slightly tilted from its direction causes …

Ultrashort Cross-Correlation In The Middle Infrared: A Novel Approach To Standoff Detection, William Conner Thomas

Department of Electrical and Computer Engineering: Dissertations, Theses, and Student Research

Lasers are a common tool in standoff detection because of their small divergence, large amount of power, and multiple wavelengths available for optical interaction. Optical signatures of targets can be composed of but are not limited to absorption, fluorescence, backscatter, polarization manipulation, and plasma spectra. This work was an investigation of a new signature phenomenon: Dispersion of middle infrared ultrashort laser pulses through gas and vapor phase molecules. Vibrational and rovibrational absorption lines of molecular species affect the spectral phase and spectral amplitude of ultrashort light pulses leading an inititally gaussian temporal profile to become distorted. This dissertation is an …

Generalized Ellipsometry On Complex Nanostructures And Low-Symmetry Materials, Alyssa Mock

Department of Electrical and Computer Engineering: Dissertations, Theses, and Student Research

In this thesis, complex anisotropic materials are investigated and characterized by generalized ellipsometry. In recent years, anisotropic materials have gained considerable interest for novel applications in electronic and optoelectronic devices, mostly due to unique properties that originate from reduced crystal symmetry. Examples include white solid-state lighting devices which have become ubiquitous just recently, and the emergence of high-power, high-voltage electronic transistors and switches in all-electric vehicles. The incorporation of single crystalline material with low crystal symmetry into novel device structures requires reconsideration of existing optical characterization approaches. Here, the generalized ellipsometry concept is extended to include applications for materials with …

Laser-Assisted Metal Organic Chemical Vapor Deposition Of Gallium Nitride, Hossein Rabiee Golgir

Department of Electrical and Computer Engineering: Dissertations, Theses, and Student Research

Due to its unique properties, gallium nitride is of great interest in industry applications including optoelectronics (LEDs, diode laser, detector), high power electronics, and RF and wirelss communication devices. The inherent shortcomings of current conventional deposition methods and the ever-increasing demand for gallium nitride urge extended efforts for further enhancement of gallium nitride deposition. The processes of conventional methods for gallium nitride deposition, which rely on thermal heating, are inefficient energy coupling routes to drive gas reactions. A high deposition temperature (1000-1100 °C) is generally required to overcome the energy barriers to precursor adsorption and surface adatom migration. However, there …

Smart Feedback Control For Fiber-Optics Acoustic Emission Sensor System, Xiangyu Luo

Department of Electrical and Computer Engineering: Dissertations, Theses, and Student Research

Optical fiber sensors for ultrasonic detection have become a subject of much research in recent years. In this thesis, a fiber-optic acoustic emission (AE) sensor system that is capable of performing AE detection, even when the sensor is experiencing large quasi-static strains, is first described. The system consists of a smart selection of a wavelength notch to which a distributed feedback (DFB) laser is locked for high sensitivity AE signal demodulation. A smart feedback control unit for the DFB laser, which is the focus of this thesis, is designed and investigated. The smart control ensures that the AE signal is …

Photoluminescence Studies Of Amorphous Boron Carbide And Tungsten Diselenide Thin Films, David M. Allendorfer

Department of Electrical and Computer Engineering: Dissertations, Theses, and Student Research

For many years scientists and engineers have been researching semi-conducting materials for use in a broad array of electronic devices. With the growing demand for faster, smaller and more efficient electronics, new materials must be characterized and their properties quantified. The focus of this thesis is to develop a system to measure photoluminescence in opto-electronic materials. Photoluminescence measurements are important because it can give researchers valuable information about a material’s band structure. This thesis begins by presenting the carrier recombination mechanisms and how they apply to photoluminescence. A system was developed to measure photoluminescence spectroscopy. This system was tested with …

Vector Magneto-Optical Generalized Ellipsometry For Determining Magneto-Optical Properties Of Thin Films, Chad Briley

Department of Electrical and Computer Engineering: Dissertations, Theses, and Student Research

Modern growth techniques allow for highly complex nano scale thin films to be created. These new films possess highly anisotropic properties structurally, optically, and magnetically that are significantly different from that of their bulk counterparts and must be accurately characterized in order to optimize desired properties for applications in next generation devices. Current magnetometry techniques focus on high symmetry characterization, namely in and out of the sample plane, and therefore do not possess the capabilities to fully explore these anisotropic properties without complicated setups and multiple sample manipulations. The author describes a setup that combines generalized ellipsometry with an octu-pole …

Ellipsometric Characterization Of Silicon And Carbon Junctions For Advanced Electronics, Alexander G. Boosalis

Department of Electrical and Computer Engineering: Dissertations, Theses, and Student Research

Ellipsometry has long been a valuable technique for the optical characterization of layered systems and thin films. While simple systems like epitaxial silicon dioxide are easily characterized, complex systems of silicon and carbon junctions have proven difficult to analyze. Traditional model dielectric functions for layered silicon homojunctions, a system with a similar structure to modern transistors, often have correlated parameters during ellipsometric data analysis. Similarly, epitaxial graphene as grown from thermal sublimation of silicon from silicon carbide or through chemical vapor deposition, tend to have model dielectric function parameters that correlate with the optical thickness of the graphene due to …

Skin Effect Suppression In Infrared-Laser Irradiated Planar Multi-Walled Carbon Nanotube/ Cu Conductors, Kamran Keramatnejad, Yang Gao, Yunshen Zhou, Hossein Rabiee Glogir, Mengmeng Wang, Yongfeng Lu

Department of Electrical and Computer Engineering: Dissertations, Theses, and Student Research

Skin effect suppression in planar multi-walled carbon nanotube (MWCNT)/Copper (Cu) conductors was realized at the 0-10 MHz frequency range through infrared laser irradiation of MWCNTs, which were coated on the surface of the Cu substrate via the electrophoretic deposition (EPD) method. The effect of laser irradiation and its power density on electrical and structural properties of the MWCNT/Cu conductors was investigated using a wavelength-tunable CO2 laser and then comparing the performance of the samples prepared at different conditions with that of pristine Cu. The irradiation at λ=9.219 μm proved to be effective in selective delivery of energy towards depths close …

Fea Estimation And Experimental Validation Of Solid Rotor And Magnet Eddy Current Loss In Single-Sided Axial Flux Permanent Magnet Machines, Xu Yang

Department of Electrical and Computer Engineering: Dissertations, Theses, and Student Research

The rotor and magnet loss in single-sided axial ux permanent magnet (AFPM) machines with non-overlapped windings is studied in this dissertation. Finite element analysis (FEA) estimations of the loss are carried out using both 2D and 3D modeling. The rotor and magnet losses are determined separately for stator slot passing and MMF space harmonics from currents in the stator. The segregation of loss between the solid rotor plate and the magnet is addressed. The eddy current loss reduction by magnet segmentation is discussed as well. Two prototype 24 slot/22 pole single-sided AFPMs, fabricated with both single layer (SL) and double …

Conductive Concrete For Electromagnetic Shielding – Methods For Development And Evaluation, Aaron P. Krause

Computer and Electronics Engineering: Dissertations, Theses, and Student Research

This research investigates the development and evaluation innovative methods for the use of conductive concrete as an electromagnetic shield. New testing methods are developed to determine the best conductive components to use in the design of a concrete mixture for shielding that shows the best promise. The conductive concrete mixture has the potential to provide electromagnetic shielding that is cost-effective in terms of construction, operation, and maintenance compared to conventional approaches. Two testing methods, Small Sample Testing and Large Slab Testing, are developed based on standardized testing methods that have been modified for the testing of conductive concrete mixtures. As …

Fiber-Tip Fabry-Perot Interferometric Sensor Based On A Thin Silver Film, Fawen Guo

Department of Electrical and Computer Engineering: Dissertations, Theses, and Student Research

Fiber-optic sensors have many advantages, including small size, light weight, immunity to electromagnetic interference, and the capability of remote sensing. Fiber- tip sensors are fabricated on a fiber tip and are the smallest type of fiber-optic sensor. The fiber-tip sensors have attracted a great deal of attention in past years for pressure, temperature, and acoustic sensing.

In this thesis, a fiber-tip sensor based on an ultra-thin silver film was proposed and demonstrated for highly sensitive and high frequency ultrasonic detection. The film is prepared by the vacuum thermal deposition method and then transferred to the fiber tip. The sensor has …

An Adaptive Utility Interactive Photovoltaic System Based On A Flexible Switch Matrix To Optimize Performance In Real-Time, Mahmoud Alahmad, Mohamed Amer Chaaban, Siu Kit Lau, Jonathan Shi, Jill Neal

Durham School of Architectural Engineering and Construction: Faculty Publications

Reconfigurable architectures are of great interest to system designers to improve the system’s operation and efficiency. In this paper, we propose an adaptive utility interactive photovoltaic (PV) system based on a novel Flexible Switch array Matrix topology. This proposed system maximizes the generated power in real-time in response to operational conditions such as shading, soiling, mismatches, and module failure among others. The proposed system is a compromise in the utilization of power conditioning equipment to maximize energy capture and system efficiency. Simulation results demonstrate an average 13% improvement in efficiency when compared with the central inverter topology performance. A prototype …

In-Situ Ellipsometry Characterization Of Anodically Grown Silicon Dioxide And Lithium Intercalation Into Silicon, Eric A. Montgomery

Department of Electrical and Computer Engineering: Dissertations, Theses, and Student Research

In this thesis, in-situ ellipsometry and electroanalytical investigations of two electrochemical processes are reported: including the formation of anodically grown silicon dioxide and the intercalation of lithium into silicon. Analysis of the ellipsometry data shows that the anodically grown silicon dioxide layer is uniform and has similar properties as thermally grown silicon dioxide. The lithium-ion intercalation data reveals non-uniform thin film formation, which requires further studies and development of appropriate ellipsometric optical models.

Advisers: Eva Schubert and Mathias Schubert

Modeling And Simulation Of Tunable Photonic Crystals, Weiqing Yang

Department of Electrical and Computer Engineering: Dissertations, Theses, and Student Research

Photonic crystals (PhCs) have wavelength scale periodically alternating refractive indexes. Photon in such structures is subject to strong scattering, experiencing distinctive redistribution of energy, yielding interesting properties such as photonic band gaps, field enhancement, strong nonlinear optic effects and photon confinement. The modified fields also alter the propagation of light beams. By proper setup, super collimation could be realized in PhCs where beams can travel long distance without spreading, while no waveguide structure is used. Redirection of light can extend the refraction to negative range, without violating physics rules. This distinguished phenomenon has been envisioned as the core mechanism for …

Generalized Ellipsometry On Sculptured Thin Films Made By Glancing Angle Deposition, Daniel Schmidt

Department of Electrical and Computer Engineering: Dissertations, Theses, and Student Research

In this thesis, physical properties of highly optically and magnetically anisotropic metal sculptured thin films made by glancing angle deposition are presented. Predominantly, the determination of optical and magneto-optical properties with spectroscopic generalized Mueller matrix ellipsometry and homogenization approaches is discussed. Nomenclatures are proposed to unambiguously identify the sculptured thin film geometry.

Generalized ellipsometry, a non-destructive optical characterization technique, is employed to determine geometrical structure and anisotropic dielectric properties of highly spatially coherent three-dimensionally nanostructured thin films in the spectral range from 400 to 1700 nm. The analysis of metal slanted columnar thin films (F1-STFs) deposited at glancing angle ( …

Feynman’S Relativistic Electrodynamics Paradox And The Aharonov-Bohm Effect, Adam Caprez, Herman Batelaan

Department of Physics and Astronomy: Faculty Publications

An analysis is done of a relativistic paradox posed in the Feynman Lectures of Physics involving two interacting charges. The physical system presented is compared with similar systems that also lead to relativistic paradoxes. The momentum conservation problem for these systems is presented. The relation between the presented analysis and the ongoing debates on momentum conservation in the Aharonov-Bohm problem is discussed.

Propagation Of Ultrashort Laser Pulses Through Water, Jianchao Li, Dennis R. Alexander, Haifeng Zhang, Ufuk Parali, David Doerr, John Clark Bruce Iii, Hao Wang

Department of Electrical and Computer Engineering: Faculty Publications

In this paper, propagation of ultrashort pulses through a long 3.5 meter water channel was studied. Of particular interest was the attenuation of the beam at various lengths along the variable path length and to find an explanation of why the attenuation deviates from typical Beer Lambert law around 3 meters for ultrashort laser pulse transmission. Laser pulses of 10 fs at 75 MHz, 100 fs at 80 MHz and 300 fs at 1 KHz were employed to investigate the effects of pulse duration, spectrum and repetition rate on the attenuation after propagating through water up to 3 meters. Stretched …

Design And Development Of A Low-Cost High Range Resolution X-Band Radar, Paul C. Cantu

Department of Electrical and Computer Engineering: Dissertations, Theses, and Student Research

Synthetic Aperture Radar (SAR) is one of the main tools for microwave remote sensing because of its multi-dimensional high resolution characteristics and the capability to operate in nearly all weather conditions, day and night. The University of Nebraska-Lincoln (UNL) initiated the design and development of a low-cost airborne SAR in January 2001 to support our Airborne Remote Sensing Program. The objectives of this project are separated into various evolutionary stages. This thesis will focus on the initial phase of design and construction of an X-band high range resolution radar (HRR) using basic RF /microwave and digital components. The following stages …