Engineering Commons^™

Fractional Order Identification Method And Control: Development Of Control For Non-Minimum Phase Fractional Order System, Majid Abdullah Alhomim

Graduate Theses and Dissertations

The increasing use of renewable energy has resulted in the need for improved a dc-dc converters. This type of electronic-based equipment is needed to interface the dc voltages normally encountered with solar arrays and battery systems to voltage levels suitable for connecting three phase inverters to distribution level networks. As grid-connected solar power levels continue to increase, there is a corresponding need for improved modeling and control of power electronic converters. In particular, higher levels of boost ratios are needed to connect low voltage circuits (less than 1000 V) to medium voltage levels in the range of 13 kV to …

Developing A Medium-Voltage Three-Phase Current Compensator Using Modular Switching Positions, Vinson Jones

Graduate Theses and Dissertations

The objective of this thesis is to present the context, application, theory, design, construction, and testing of a proposed solution to unbalanced current loading on three-phase four-wire systems. This solution, known as the Medium-Voltage Unbalanced Current Static Compensator or MV-UCSC, is designed to recirculate currents between the three phases of adistribution system. Through this redistribution of the currents negative- and zero-sequence current components are eliminated and a balanced load is seen upstream from the point of installation. The MV-UCSC as it operates in the distribution system is presented followed by its effect on traditional compensation equipment. The construction of the …

High-Temperature Optoelectronic Device Characterization And Integration Towards Optical Isolation For High-Density Power Modules, Syam Madhusoodhanan

Graduate Theses and Dissertations

Power modules based on wide bandgap (WBG) materials enhance reliability and considerably reduce cooling requirements that lead to a significant reduction in total system cost and weight. Although these innovative properties lead power modules to higher power density, some concerns still need to be addressed to take full advantage of WBG-based modules. For example, the use of bulky transformers as a galvanic isolation system to float the high voltage gate driver limits further size reduction of the high-temperature power modules. Bulky transformers can be replaced by integrating high-temperature optocouplers to scale down power modules further and achieve disrupting performance in …

Robust Control Of A Multi-Phase Interleaved Boost Converter For Photovoltaic Application Using Μ-Synthesis Approach, Badur Mueedh Alharbi

Graduate Theses and Dissertations

The high demand of energy efficiency has led to the development power converter topologies and control system designs within the field of power electronics. Recent advances of interleaved boost converters have showed improved features between the power conversion topologies in several aspects, including power quality, efficiency, sustainability and reliability.

Interleaved boost converter with multi-phase technique for PV system is an attractive area for distributed power generation. During load variation or power supply changes due to the weather changes the output voltage requires a robust control to maintain stable and perform robustness.

Connecting converters in series and parallel have the advantages …

Design Of A 350 Kw Silicon Carbide Based 3-Phase Inverter With Ultra-Low Parasitic Inductance, Matthew Feurtado

Graduate Theses and Dissertations

The objective of this thesis is to present a design for a low parasitic inductance, high power density 3-phase inverter using silicon-carbide power modules for traction application in the electric vehicles with a power rating of 350 kW. With the market share of electric vehicles continuing to grow, there is a great opportunity for wide bandgap semiconductors such as silicon carbide (SiC) to improve the efficiency and size of the motor drives in these applications. In order to accomplish this goal, careful design and selection of each component in the system for optimum performance from an electrical, mechanical, and thermal …

Synthesis And Application Of Ceramic Paste For High-Temperature Electronic Packaging, Ardalan Nasiri

Graduate Theses and Dissertations

This dissertation research focused on the synthesis and application of ceramic paste for high-temperature applications. An alumina paste material comprising aluminum dihydric phosphate and alumina powder was developed for high-temperature electronic packaging. Nano aluminum nitride and nano-silica powders were embedded to promote the paste curing process, limit the grain growth, and increase its bond shear strength. The chip-to-substrate bond strength was enhanced and met the MIL-STD requirements for die-attach assembly. Its encapsulation property was improved with fewer cracks compared to similar commercial ceramic encapsulants. The die-attach material and encapsulation properties tested at 500°C showed no defect or additional cracks. Thermal …

Development Of A Reference Design For A Cyber-Physical System, Nicholas Paul Blair

Graduate Theses and Dissertations

The purpose of this thesis is to develop a reference design to assist in the selection of security practices in power electronics design. A prototype will be developed from this reference design for evaluation. This evaluation will include a brief cost/benefit analysis to gauge the efficacy of implementing each layer of security throughout the power electronics design process. This thesis will also describe the obstacles and effectiveness of integrating a Trusted Platform Module (TPM) into a cyber-hardened grid-connected device. The TPM device is a secured crypto processor that assists in generating, storing, and restricting the use of cryptographic keys. The …

A Power Constrained 433-Mhz Low Noise Amplifier, Pablo Alvarez Arellano

Graduate Theses and Dissertations

Within wireless communication systems, low noise amplifiers are critical for the performance of receivers. They are primarily responsible for providing enough gain while adding little noise to overcome the noise of the subsequent stages. The LNA presented here is part of a battery-powered transceiver meant to measure crop nutrient data and relay the information. Therefore, power consumption and area become import considerations. To design for a specific power level, a power-constrained noise optimization method is used. The method sizes the amplifying transistor for a fixed source impedance, power dissipation, technology, and operating frequency. The chosen topology is the cascode stage …

Cybersecurity Methods For Grid-Connected Power Electronics, Stephen Joe Moquin

Graduate Theses and Dissertations

The present work shows a secure-by-design process, defense-in-depth method, and security techniques for a secure distributed energy resource. The distributed energy resource is a cybersecure, solar inverter and battery energy storage system prototype, collectively called the Cybersecure Power Router. Consideration is given to the use of the Smart Green Power Node for a foundation of the present work. Metrics for controller security are investigated to evaluate firmware security techniques. The prototype's ability to mitigate, respond to, and recover from firmware integrity degradation is examined. The prototype shows many working security techniques within the context of a grid-connected, distributed energy resource. …

A Novel Three-Level Isolated Ac-Dc Pfc Power Converter Topology With Reduced Number Of Switches, Obaid Aldosari

Graduate Theses and Dissertations

The three-level isolated AC-DC power factor corrected (PFC) converter provides safe and more efficient power conversion. In comparison with two-level, three-level PFC converter has the advantages of low total harmonic distortion, low device voltage rating, low di/dt, better output performance, high power factor, and low switching losses at higher switching frequencies. The high frequency transformer (HFT) grants galvanic isolation, steps up or down secondary voltage, and limits damage in case of a fault current.

The existing three-level converter based on solid-state transformer (SST) topologies convert ac power from the electrical grid to a dc load while maintaining at least the …

A Virtual Space Vectors Based Model Predictive Control For Three-Level Converters, Waleed Saad S. Alhosaini

Graduate Theses and Dissertations

Three-phase three-level (3-L) voltage source converters (VSC), e.g., neutral-point clamped (NPC) converters, T-type converters, etc., have been deemed to be suitable for a wide range of medium- to high-power applications in microgrids (MGs) and bulk power systems. Compared to their two-level (2-L) counterparts, adopting 3-L VSCs in the MG applications not only reduces the voltage stress across the power semiconductor devices, which allows achieving higher voltage levels, but also improves the quality of the converter output waveforms, which further leads to considerably smaller output ac passive filters.

Various control strategies have been proposed and implemented for 3-L VSCs. Among all …

Investigations Of New Fault-Tolerant Methods For Multilevel Inverters, Haider Mhiesan

Graduate Theses and Dissertations

The demands of power electronics with high power capability have increased in the last decades. These needs have driven the expansion of existing power electronics topologies and developing new power electronics generations. Multilevel inverters (MLI) are one of the most promising power electronics circuits that have been implemented and commercialized in high-voltage direct current (HVDC), motor drives, and battery energy storage systems (BESS). The expanding uses of the MLI have lead to creation of new topologies for different applications. However, one of the disadvantages of using MLIs is their complexity. MLIs consist of a large number of switching devices, which …

Study Of A Symmetrical Llc Dual-Active Bridge Resonant Converter Topology For Battery Storage Systems, John K. George

Graduate Theses and Dissertations

A symmetrical LLC resonant converter topology with a fixed-frequency quasi-triple phase-shift modulation method is proposed for battery-powered electric traction systems with extensions to other battery storage systems. Operation of the converter with these methods yields two unique transfer characteristics and is dependent on the switching frequency. The converter exhibits several desirable features: 1) load-independent buck-boost voltage conversion when operated at the low-impedance resonant frequency, allowing for dc-link voltage regulation, zero-voltage switching across a wide load range, and intrinsic load transient resilience; 2) power flow control when operated outside the low-impedance resonance for integrated battery charging; 3) and simple operational mode …

Design And Optimization Of A High Power Density Silicon Carbide Traction Inverter, Tyler Adamson

Graduate Theses and Dissertations

This project was initiated with the goal of demonstrating a 3-phase silicon carbide based 150-kW 25 kW/L DC-AC power conversion unit capable of operation with coolant temperatures up to 90°C. The project goals were met and exceeded by first analyzing the established inverter topologies to find which one would yield the highest power density while still meeting electrical performance needs in the 150-kW range. Following topology selection, the smallest silicon carbide power module that met the electrical requirements of the system was found through experimental testing and simulation. After a power module selection was finalized, a DC link capacitor bank …

High Frequency Ltcc Based Planar Transformer, Adithya Venkatanarayanan

Graduate Theses and Dissertations

As we move towards high power and higher frequency related technology, conventional wire-wound magnetics have their own limitations which has led path to the development of planar based magnetic materials. Nowadays more planar magnetic technology has been employed because it is easier to fabricate them. The planar magnetic is a transformer or an inductor that replaces the wire-wound transformer or inductors which generally uses copper wires. One of the main reasons why we move to planar magnetic technology is its operation at higher frequency which provides higher power density. This study explains in detail about the design and fabrication of …

Synchrophasor-Based Fault Location Detection And Classification, In Power Systems, Using Artificial Intelligence, Hemal Falak

Graduate Theses and Dissertations

With the introduction of sophisticated electronic gadgets which cannot sustain interruption in the provision of electricity, the need to supply uninterrupted and reliable power supply, to the consumers, has become a crucial factor in the present-day world. Therefore, it is customary to correctly identify fault locations in an electrical power network, in order to rectify faults and restore power supply in the minimum possible time. Many automated fault location detection algorithms have been proposed, however, prior art requires topological and physical information of the electrical power network. This thesis presents a new method of detecting fault locations, in transmission as …

Development Of A Rapid Fatigue Life Testing Method For Reliability Assessment Of Flip-Chip Solder Interconnects, Cody Jackson Marbut

Graduate Theses and Dissertations

The underlying physics of failure are critical in assessing the long term reliability of power packages in their intended field applications, yet traditional reliability determination methods are largely inadequate when considering thermomechanical failures. With current reliability determination methods, long test durations, high costs, and a conglomerate of concurrent reliability degrading threat factors make effective understanding of device reliability difficult and expensive. In this work, an alternative reliability testing apparatus and associated protocol was developed to address these concerns; targeting rapid testing times with minimal cost while preserving fatigue life prediction accuracy. Two test stands were fabricated to evaluate device reliability …

Stability Analysis Of A High-Power Microgrid, David Manuel Carballo Rojas

Graduate Theses and Dissertations

The objective of this thesis is to perform the modeling and stability analysis of a high-power microgrid with multiple parallel-and grid connected voltage source converters using the system parameters from the high-power microgrid testbed at the National Center for Reliable Electric Power Transmission (NCREPT) at the University of Arkansas in order to identify, minimize, if not eliminate, the potential instabilities that can affect the proper operation of the microgrid testbed. To achieve this objective, the mathematical modeling of the high-power microgrid considering the adverse effects of resonances due to interactions among the converter LCL output filters is presented and analyzed. …

Fully Analog Laser Driver With Robust Active Feedback Control, John Petrilli

Graduate Theses and Dissertations

The objective of this project was to go through a real life engineering development cycle, document and justify the design choices, and use background experience in electronic design and control systems to implement the best design possible. The laser driver implemented in this project is designed for the general use of a large variety of diodes in continuous wave mode, much like off the shelf laser drivers. The design goals included improving upon off the shelf laser drivers by decreasing steady state error, setting time, response time, and overshoot. Many different feedback control systems were evaluated, and a modified PID …

Developing A Hil-Based Software Platform For Testing Electric And Hybrid Vehicle Powertrains, Daniel Schwartz

Graduate Theses and Dissertations

The objective of this thesis is to present a dynamometer test stand with hardware in the loop (HIL) testing capabilities for the evaluation of electric and hybrid vehicle powertrains under realistic driving conditions. The traction inverter and dc/dc converter are two crucial subsystems of the powertrain and new prototypes require significant validation before implementing into production vehicles. As fundamental technologies such as power modules, thermal management systems, and passive components improve; the performance improvements to the overall system must be demonstrated. The plug and play nature of the testbed makes it ideal for making direct comparisons of design iterations under …

Fabrication And Characterization Of Graphene Based 2d Materials For Supercapacitors, Anishkumar Manoharan

Graduate Theses and Dissertations

Supercapacitors have attracted a lot attention due to their efficient energy storage. In comparison to batteries, supercapacitors have high capacitance, energy, and power densities per unit mass than conventional capacitors. Carbon based materials are most promising in supercapacitor application due to their outstanding physical and electrochemical behavior. In this work, a facile method to synthesize a nanocomposite electrode consisting of annealed carbon from carbon ink and MoS2 was demonstrated. Effects of various aqueous and solid electrolytes were studied. It was found that the nanocomposite electrode with 10% MoS2 and 1M Na2SO4 as the aqueous electrolyte tested using the three electrode …

Gating Methods For High-Voltage Silicon Carbide Power Mosfets, Audrey Dearien

Graduate Theses and Dissertations

The objective of this thesis is to assess the challenges associated with driving Silicon Carbide (SiC) power devices, and to compare the potential gate drive methods for these devices which address those challenges. SiC power devices present many benefits that make them suitable for next generation automotive, power utility grid, and energy management applications. High efficiency, increased power density, and reliability at high-temperatures are some of the main benefits of SiC technology. However, the many challenges associated with these devices have prevented their adoption into industry applications. The argument is made in this thesis that the gate driver is a …

Application Of Modular Multilevel Converters (Mmc) Using Phase-Shifted Pwm And Selective Harmonic Elimination In Distribution Systems, Thouhidul Islam

Graduate Theses and Dissertations

Reducing the size and weight of a power electric system is a prodigious challenge to researchers as the development of the latest technologies emerge in the field of electrical engineering. A similar urge is there to develop a light-weight mobile power substation (MPS) to use in the electric power distribution systems during emergency conditions. This thesis proposes a power electronics based solution using the modular multilevel converter (MMC) topology to design the MPS system. The market-available power semiconductor devices are analyzed and suitable devices are selected to design the system. The phase-shifted pulse width modulation (PS-PWM) and selective harmonic elimination …

Evaluation Of Terahertz Imaging For Breast Cancer Detection Using Image Morphing, Tanny Andrea Chavez Esparza

Graduate Theses and Dissertations

This thesis proposes the use of a mesh morphing algorithm for the quantitative evaluation of terahertz (THz) images. This work differs from traditional evaluation methods based on qualitative evaluation because it provides a fair and quantitative measurement of the THz imaging system's performance. The objective of the algorithm is to match the alignment, shape, and resolution of the THz and reference pathology images. Therefore, the proposed morphing method provides a pathology reference for a pixel-by-pixel evaluation of the region classification in the THz image. To achieve this, the morphing algorithm aligns the images using the Pearson's correlation coefficient and reshapes …

Power Interface Design And System Stability Analysis For 400 V Dc-Powered Data Centers, Yuzhi Zhang

Graduate Theses and Dissertations

The demands of high performance cloud computation and internet services have increased in recent decades. These demands have driven the expansion of existing data centers and the construction of new data centers. The high costs of data center downtime are pushing designers to provide high reliability power supplies. Thus, there are significant research questions and challenges to design efficient and environmentally friendly data centers with address increasing energy prices and distributed energy developments.

This dissertation work aims to study and investigate the suitable technologies of power interface and system level configuration for high efficiency and reliable data centers.

A 400 …

Asynchronous 3d (Async3d): Design Methodology And Analysis Of 3d Asynchronous Circuits, Francis Corpuz Sabado

Graduate Theses and Dissertations

This dissertation focuses on the application of 3D integrated circuit (IC) technology on asynchronous logic paradigms, mainly NULL Convention Logic (NCL) and Multi-Threshold NCL (MTNCL). It presents the Async3D tool flow and library for NCL and MTNCL 3D ICs. It also analyzes NCL and MTNCL circuits in 3D IC. Several FIR filter designs were implement in NCL, MTNCL, and synchronous architecture to compare synchronous and asynchronous circuits in 2D and 3D ICs. The designs were normalized based on performance and several metrics were measured for comparison. Area, interconnect length, power consumption, and power density were compared among NCL, MTNCL, and …

Energy-Aware Sparse Sensing Of Spatial-Temporally Correlated Random Fields, Zuoen Wang

Graduate Theses and Dissertations

This dissertation focuses on the development of theories and practices of energy aware sparse sensing schemes of random fields that are correlated in the space and/or time domains. The objective of sparse sensing is to reduce the number of sensing samples in the space and/or time domains, thus reduce the energy consumption and complexity of the sensing system. Both centralized and decentralized sensing schemes are considered in this dissertation.

Firstly we study the problem of energy efficient Level set estimation (LSE) of random fields correlated in time and/or space under a total power constraint. We consider uniform sampling schemes of …

Energy Shaping Control For Stabilization Of Interconnected Voltage Source Converters In Weakly-Connected Ac Microgrid Systems, Nadia Lenora Carmita Smith

Graduate Theses and Dissertations

With the ubiquitous installations of renewable energy resources such as solar and wind, for decentralized power applications across the United States, microgrids are being viewed as an avenue for achieving this goal. Various independent system operators and regional transmission operators such as Southwest Power Pool (SPP), Midcontinent System Operator (MISO), PJM Interconnection and Electric Reliability Council of Texas (ERCOT) manage the transmission and generation systems that host the distributed energy resources (DERs). Voltage source converters typically interconnect the DERs to the utility system and used in High voltage dc (HVDC) systems for transmitting power throughout the United States. A microgrid …

Realization Of A High Power Microgrid Based On Voltage Source Converters, Yusi Liu

Graduate Theses and Dissertations

Microgrid concepts are gradually becoming more popular because they are expected to interface with renewable energies, increase end users’ reliability and resiliency, and promote seamless integration of distributed generators (DG) and energy storage units [1]. Most units are connected through power electronics interfaces, such as ac-dc, dc-dc, and dc-ac converters. The converter design and control are critical to the stability and efficiency of a microgrid.

A microgrid may operate in either gird connected mode or islanded mode [1]. In terms of stability, the grid connected mode is less challenging compared to the islanded mode of operation due to the nearly …

Investigation Of Fes2 Nanoparticles For Use In Optoelectronic And Thermoelectric Applications, Rick Tefal Eyi Nkoghe

Graduate Theses and Dissertations

Iron pyrite (FeS2) is the most abundant sulfide material on earth. This material has been widely investigated by researchers because of its optical properties. However, it has been difficult to produce High efficiency FeS2 based solar cells. This is due to many different impurities that arise when making the materials. The ability to synthesize pure pyrite FeS2 material is therefore critical for applications.

Pure Iron pyrite nanocrystals were synthesized using hot injection by mixing sulfur with an iron precursor in the presence of an amine. To improve the stability, shorter ligands replaced the native amines ligands. The stability of the …