Engineering Commons^™

Uncertainty Of The Ultrasonic Method For Determining The Strength Of Concrete, Ortagoli Sharipovich Hakimov, Zamira Khudoyberdiyevna Ernazarova

Chemical Technology, Control and Management

The issues of measuring the strength of concrete by the method of surface sounding by ultrasound are considered. A measurement model and formulas for estimating the total standard measurement uncertainty, information about the standards used, measurement tools and methods, and environmental parameters are given. Information about the estimation of uncertainty in the form of "eight steps", such as: measurement task; mathematical model of measurement; analysis of input values; observation results; correlations; uncertainty budget; expanded uncertainty; measurement result. It has been established that the uncertainty of type B of the ultrasonic method for determining the strength of concrete is much less …

Problems Of Modeling And Control Of The Technological Process Of Ore Grinding, Djalolitdin Pakhritdinovich Mukhitdinov, Sanjar Boybutayev

Chemical Technology, Control and Management

The article analyzes the methods of mathematical modeling of the closed-loop process of fine grinding of ore in order to predict the composition of the crushed raw material. Analyzed modeling methods that consider the control of classification of crushed raw materials and finished products by the size of the recirculating load, simulation modeling methods, methods that use neuro-phase netthe research apparatus, in which the fuzzy logic apparatus serves as a fundamental component for the formation of conclusions. The materials presented in the article reflect the theoretical substantiation and generalization of the accumulated practical experience in modeling and control of the …

Active Stability Monitoring And Stability Control Of Dc Microgrids Using Incremental Continuous Injection, Rohail Hassan

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

Electrified transportation and integration of renewable energy in the electric power grid requires the use of power electronic converters for integrating different forms of power; from ac to dc, dc to ac, dc to dc, etc. Recent trend towards electrifying automobiles, aircraft and ships, and increasing penetration of renewable energy has increased the required power levels and number of the power electronics converters connected together in a dc microgrid system. Stable operation of these interfacing converters for all operating conditions has been a topic of renewed interest in the last couple of decades. Traditionally, dc microgrids have been designed conservatively …

Control Of Series Connected Battery Powered Modules, Joshua K. Wooten

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

Batteries are a very common type of power source used for all sorts of applications. However, these batteries do not last forever. The purpose of this thesis is to explain and implement a strategy which allows batteries to have a second life; to be able to be re-charged and re-used for another set period of time once they no longer meet a system’s requirements. The preferable way to do this is to make each cell have the same state of charge (SOC) which will lead to a longer lasting battery pack. These batteries will be hooked up to a battery …

Direct Torque Control For Silicon Carbide Motor Drives, Mohammad Hazzaz Mahmud

Graduate Theses and Dissertations

Direct torque control (DTC) is an extensively used control method for motor drives due to its unique advantages, e.g., the fast dynamic response and the robustness against motor parameters variations, uncertainties, and external disturbances. Using higher switching frequency is generally required by DTC to reduce the torque ripples and decrease stator current total harmonic distortion (THD), which however can lower the drive efficiency. Through the use of the emerging silicon carbide (SiC) devices, which have lower switching losses compared to their silicon counterparts, it is feasible to achieve high efficiency and low torque ripple simultaneously for DTC drives.

To overcome …

Adaptive Control And Parameter-Dependent Anti-Windup Compensation For Inertia Varying Quadcopters., Benjamin Edwards Farber

Electronic Theses and Dissertations

A novel parameter-dependent anti-windup compensator is developed to improve the performance of a saturation constrained model reference adaptive controller. The combined control structure solves the input saturation and stability problem for inertia varying quadcopters. The control synthesis follows the conventional two-step anti-windup design paradigm where a nominal controller is designed without consideration of the input saturation, and the anti-windup compensator is designed to minimize deviations from nominal performance caused by saturated inputs. To account for varying inertia of the quadcopter during package retrieval/delivery routines, the inertia parameters of the vehicle/package are estimated with an online recursive system identification technique, and …

On The Impact Of Gravity Compensation On Reinforcement Learning In Goal-Reaching Tasks For Robotic Manipulators, Jonathan Fugal, Hasan A. Poonawala, Jihye Bae

Electrical and Computer Engineering Faculty Publications

Advances in machine learning technologies in recent years have facilitated developments in autonomous robotic systems. Designing these autonomous systems typically requires manually specified models of the robotic system and world when using classical control-based strategies, or time consuming and computationally expensive data-driven training when using learning-based strategies. Combination of classical control and learning-based strategies may mitigate both requirements. However, the performance of the combined control system is not obvious given that there are two separate controllers. This paper focuses on one such combination, which uses gravity-compensation together with reinforcement learning (RL). We present a study of the effects of gravity …

Control Synthesis For Parametric Timed Automata Under Reachability, Ebru Aydin Göl

Turkish Journal of Electrical Engineering and Computer Sciences

Timed automata is a fundamental modeling formalism for real-time systems. During the design of such real-time systems, often the system information is incomplete, and design choices can vary. These uncertainties can be integrated to the model via parameters and labelled transitions. Then, the design can be completed by tuning the parameters and restricting the transitions via controller synthesis. These problems, namely parameter synthesis and controller synthesis, are studied separately in the literature. Herein, these are combined to generate an automaton satisfying the given specification by both parameter tuning and controller synthesis, thus exploring all design choices. First, it is shown …

Analysis Of Three-Phase Rectifier Via Three Different Control Methods And Switch Power Loss Comparison, Yichao Wang

All Graduate Theses, Dissertations, and Other Capstone Projects

Traditional uncontrolled or phase-controlled rectifiers have the defects of lower power factor and nontrivial higher harmonics which causes the low efficiency of power, bad power quality, and so on. However, PWM rectifiers overcome the drawbacks mentioned above. They reduce the higher harmonics yielding better sinusoidal current on the grid side, achieve unity power factor and bidirectional power flow, and have better dynamic performance. So, it is favored more by academia and widely applied in high-performance power electronics devices. In this paper, the PWM rectifier is analyzed and a comparison of the switch loss on three-phase rectifier using three different control …