Engineering Commons^™

Comparison Of Safety Performance By Design Types At Freeway Diverge Areas And Exit Ramp Sections, Hongyun Chen

USF Tampa Graduate Theses and Dissertations

The primary objective of the study is to evaluate the safety performance of different freeway exit types used in current practical designs. More specific, the research objectives include the following two parts: 1) to compare the safety performance of different design types at freeway diverge areas and exit ramp sections; and 2) to identify the impact factors contributing to the crashes happening at these two specific segments.

The study area includes four subjects, the freeway widely-spaced diverge areas; the freeway closely-spaced diverge areas; the left-side off-ramps and the exit ramp sections. For the freeway diverge areas, design types were defined …

A Multicriteria Based Quantitative Framework For Assessing Sustainability Of Pile Foundations, Aditi Misra

Master's Theses

ABSTRACT

Civil Engineering is the major instrument of anthropocentric development over centuries through ever expanding infrastructure, cities and facilities. Civil engineering processes are both resource and fuel intensive. The building industry alone, during the construction stage, uses about 30-40% of the total resources used in the industrialized countries. There is a growing consensus that delivering a sustainable built environment starts with incorporating sustainability thoughts at the planning and design stages of a project. Geotechnical engineering is most resource intensive although this intensive consumption of energy goes unnoticed mainly because of the indirect nature of the energy used in the …

The Use Of Building Information Modeling In Generating Hard Bid Estimates, Peter Samuel Jensen

Theses and Dissertations

Building Information Modeling has provided many benefits to the architectural, engineering, construction and facilities management communities. Many studies have been done to validate the asserted benefits, including benefits to the field of estimating. The studies on estimating are currently limited to the realm of conceptual estimates, and have only treated detailed estimates in the abstract. The purpose of this study was to determine how BIM was being used by companies in a hard bid, or detailed estimate scenario. The research team used the Deseret Towers housing project at Brigham Young University as the basis for the research. A building information …

Fotogrametría Terrestre Aplicada A Modelos Físicos Del Laboratorio De Procesos Geotécnicos, Marinela Pinzón Muñóz

Ingeniería Civil

No abstract provided.

Wake Dynamics And Passive Flow Control Of A Blunt Trailing Edge Profiled Body, Lakshmana Sampat Doddipatla

Electronic Thesis and Dissertation Repository

Wake flows behind two-dimensional bodies are dominated mainly by two types of coherent structures, namely, the Karman Benard vortices and the streamwise vortices, also referred to as rolls and ribs respectively. The three-dimensional wake instabilities lead to distinct instability modes (mode-A, mode-B and mode-C or mode S) depending on the flow Reynolds number and geometric shape. The present investigation explores the mechanism by which the flow transitions take place to three-dimensionality in the near wake of a profiled leading edge and blunt trailing edge body. Experiments consisting of a combination of Planar Laser Induced Fluorescence visualizations and Particle Image Velocimetry …

Hydraulic Conductivity Of Cement-Treated Soils And Aggregates After Freezing, Michael Scott Shea

Theses and Dissertations

Improvements in the strength and durability of frost-susceptible soils and aggregates can be achieved through chemical stabilization using portland cement, where the efficacy of cement stabilization for improving durability depends on the degree to which hydraulic conductivity is reduced. Hydraulic conductivity is commonly estimated from basic soil properties using Moulton's empirical equation. However, the hydraulic conductivity estimation does not consider the detrimental effects of freezing or the benefits of cement stabilization. The purpose of this research was to derive new equations relating hydraulic conductivity after freezing to specific material properties of cement-treated soils and aggregates stabilized with different concentrations of …

Modelación Física De Sumideros Laterales Tipo Ventana Para Vías Urbanas, Miguel Ángel Barragán Ochica

Ingeniería Civil

El proyecto comprende dos partes principales. La primera de carácter teórico, en la cual se hizo un análisis del estado del arte con respecto al estudio de los sumideros laterales tipo ventana y se realizaron salidas de campo con el fin de recopilar un inventario sobre las características principales de los sumideros estudiados en este proyecto. La segunda parte enmarca el trabajo de laboratorio, en el cual se construyó un modelo a escala de una vía urbana (Ver Imagen 1), y con este modelo se 6 realizaron mediciones del caudal resumido por los sumideros laterales bajo diversas condiciones. Entre las …

Environmental Impacts To Stream Acidification And Brook Trout Populations In The Great Smoky Mountains National Park, Keil Jason Neff

Doctoral Dissertations

This research supports development of aquatic resource management strategies to address acid deposition in the Great Smoky Mountain National Park (GRSM) by 1) developing relationships between baseflow and stormflow chemical constituents and examining effects of elevation, area, geology, soil, and vegetation on stream chemistry; 2) evaluating physiological condition in brook trout in relation to changes in stream chemistry during stream acidification episodes, and 3) evaluating brook trout metrics with respect to stream chemistry, basin characteristics, and ecologically relevant hydrologic parameters. (1) Stream chemistry was monitored in eight GRSM streams considering basin area, site elevation, Anakeesta geology, soil, and vegetation. Following …

Durability And Fatigue Behavior Of Cip Concrete Connections For Accelerated Bridge Construction, Peng Zhu

Doctoral Dissertations

Continuous longitudinal and transverse U-bar joint connections between flanges of the decked bulb-Ts (DBTs) or between precast panels for accelerated bridge construction are investigated. The procedure for selecting durable closure pour (CP) materials for the connections is discussed firstly. The accelerated construction is quantified as two categories: overnight cure and 7-day cure of CP materials. Candidate materials are selected first based on literature review as well as tests of compressive strength and flow and workability. Then, performance criteria for selecting durable CP materials for both categories are developed based on durability tests of selected candidate materials. These durability tests include …

Investigating Wood Welding Parameters Using A Prototype Welding Machine, Timothy R. Melin

Master's Theses

Understanding how different processing variables influence wood welded bonds is vital if the technique will ever be used to create engineered lumber without using adhesives. A variation of vibration welding, wood welding uses pressure and friction to bond materials together. During welding, heat causes a softening in the wood, a naturally occurring composite material. This softening leads to fiber entanglement and a bond forms upon cooling.

The goal of this research was to investigate several processing aspects of the wood welding procedure. A prototype wood welding machine, designed and fabricated from the ground up, was used to investigate the effects …

Stability Analysis Of Single And Double Steel Girders During Construction, Sean Justin Coffelt

Masters Theses

Built-up steel I-girders are very commonly used in bridge construction. Their spans are typically very long, and they are susceptible to lateral torsional buckling if not enough lateral support is provided. This thesis includes guidelines for preventing lateral torsional buckling of steel I-girders under dead and wind load, accompanied with finite element analysis of double girder systems. The first portion includes capacity envelopes for single girders with single and double symmetric cross sections under various loading conditions and boundary conditions for double and single symmetric cross sections with double girders subjected to dead loads only. The second portion is dedicated …

Seismic Analysis Of Integral Abutment Bridges Considering Soil Structure Interaction, Reza Vasheghani Farahani

Masters Theses

Integral abutment bridges are jointless bridges in which the deck is continuous and connected monolithically with the abutment walls supported typically by a single row of piles. This thesis focuses on the effects of two major parameters on the seismic behavior of an integral abutment bridge in Tennessee by considering soil-structure interaction around the piles and in back of the abutments: (1) clay stiffness (medium vs. hard) around the piles, and (2) level of sand compaction (loose vs. dense) of the abutment wall backfilling. Modal and nonlinear time history analyses are performed on a three dimensional detailed bridge model using …

Wind River Range Snowpack Reconstruction Using Dendochronology And Sea Surface Temperatures, Sallyrose Anderson

Masters Theses

Multiple reconstructions of April 1st snow water equivalent (SWE) are generated for the Wind River Range (WRR), located in west-central Wyoming, to determine the most accurate predictors. Predictors included climate signal data (Southern Oscillation Index), traditional predictors (tree-ring chronologies), and non-spatially biased Pacific Ocean sea surface temperatures (SSTs). Incorporation of Pacific Ocean SSTs as a whole provides a more comprehensive representation of oceanic-atmospheric variability. Rotated principal component analysis (PCA) was used to regionalize April 1st snowpack data (1961 – 1999) from snow telemetry stations (SNOTEL stations). Tree-ring chronologies that were stable across the period of overlapping records (1961 – 1999) …

Modeling Greenhouse Gas Emissions From Conventional Wastewater Treatment Plants In South Carolina, Andrea Hicks

All Theses

Wastewater treatment is an essential part of life in the urbanized world. As global climate change becomes a more pressing issue, the greenhouse gas emissions created through wastewater treatment will become a more prominent concern. Tertiary treatment will likely be standard for wastewater treatment plants in the near future, and therefore must be included in a model of greenhouse gas emissions. Also, the geographic location of a WWTP will change the mix of power types (e.g., coal, nuclear, biomass) used to run the plant. Although GHG emissions from the waste sector are small compared to the emissions of the United …

Destructive Testing Of Composite Precast Concrete Deck Panels And Built-Up Steel Plate Girders, Wesley J. Cook

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

The Utah Department of Transportation (UDOT) has implemented the use of precast concrete panels for bridge deck construction. A bridge utilizing these panels as a reconstruction method was decommissioned three years after the new deck installation, due to unrelated matters. Two sections of this bridge were salvaged and sent to Utah State University (USU) for destructive testing.

Each bridge section consisted of two built-up steel plate girders intact with the precast concrete deck panels. The precast panels were designed and constructed to achieve full composite action between the deck and built-up steel plate girders through the use of Nelson shear …

Destructive Testing And Finite-Element Modeling Of Full-Scale Bridge Sections Containing Precast Deck Panels, Travis R. Brackus

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

Full-depth, precast panel deck systems are becoming more common in bridge installation and repair. The objective of these systems is to achieve the performance of cast-in-place systems while simultaneously saving time and money. The structural behavior of these systems has been the subject of scrutiny in recent research. The Utah Department of Transportation demolished a steel I-girder bridge containing a precast panel deck system and provided two full-scale specimens for this project. Destructive testing was performed at Utah State University on the specimens to investigate three failure modes: flexural, beam shear, and punching shear. Finite-element models were created using ANSYS …

Estimating And Verifying Household Potential To Conserve Water, Francisco J. Suero

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

This thesis identifies impacts of behaviors and technology on residential indoor water use and conservation efforts. We use pre-existing detailed end-use data collected before and after toilets, faucets, showerheads, and clothes washers were retrofitted in 96 owner-occupied, single-family households in Oakland, California; Seattle, Washington; and Tampa, Florida between 2000 and 2003.

Water volume, duration of use, and time of use were recorded and disaggregated by appliance for two weeks before and four weeks after appliances were retrofitted. For each appliance, we compare observed differences in water use before and after retrofits to water savings predicted by analytical engineering, semi-analytical engineering, …

Retrieval Of Aerosol Mass Concentration From Elastic Lidar Data, Christian C. Marchant

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

Agricultural aerosol sources can contribute significantly to air pollution in many regions of the country. Characterization of the aerosol emissions of agricultural operations is required to establish a scientific basis for crafting regulations concerning agricultural aerosols. A new lidar instrument for measuring aerosol emissions is described, as well as two new algorithms for converting lidar measurements into aerosol concentration data. The average daily aerosol emission rate is estimated from a dairy using lidar.

The Aglite Lidar is a portable scanning lidar for mapping the concentration of particulate matter from agricultural and other sources. The instrument is described and performance and …

Evaluation Of Utility Relocation Costs And Best Management Practices, Michael Reinke

All Theses

In recent years, the SCDOT has experienced a significant variation in estimated costs for the relocation of utilities on many projects. This has led to cost overruns and caused concerns for the district engineers responsible for the projects. Through meetings with SCDOT personnel and utility company representatives it was determined that a standardized cost estimate form combined with improved change order management and cost management strategies was needed. Recently submitted estimates were analyzed and rated by a panel on multiple criteria to generate a list of 'poor', 'good', and 'excellent' estimates. The 'excellent' estimates provided insight into the development of …

Determining The Global Maximum Biofuel Production Potential Without Conflicting With Food And Feed Consumption, Watcharapol Pumkaew

All Theses

This study tries to resolve the competition between food and biofuel by balancing the allocation between food and feed areas and biofuel areas for the entire world. The maximum energy production is calculated by determining the theoretical amount of energy that can be grown, once food and feed consumption is taken into account, based on the assumption that unprotected grass and woody lands and forest lands can be converted into cultivated lands. The total optimum land area for biofuel energy, 4,926.49 Mha, consists of corn, rapeseed, sugar beet, sugar cane, and grasses. When considering energy conversion efficiency, the maximum energy …

Determination Of Sorption Coefficients For Neptunium, Plutonium, Iodine, And Technetium In Engineered And Natural Systems Under Oxidizing And Reducing Conditions, Michael Lilley

All Theses

Plutonium, neptunium, technetium, and iodine present appreciable risks at nuclear waste disposal sites around the world due to their potential mobility. Sorption of each of these radionuclides is profoundly influenced by oxidation/ reduction reactions. Therefore, the mobility of each radionuclide may be greatly influenced by redox conditions of the natural or engineered system. The primary focus of this study was to determine distribution coefficients (K_d) for each radionuclide for engineered concrete and saltstone systems with varying amounts of reducing slag (a cement additive to create a reducing environment), and for iodide/iodate in natural sediments. Saltstones are a mixture …

A Numerical And Experimental Study Of Differential Settling In Cohesive Sediment, Chad Heiliger

All Theses

Accurate sedimentation modeling has important applications in a number of fields. This includes modeling the accumulation of sediment in harbor channels and modeling the sedimentation and accumulation of particles in retention ponds in the still waters behind dams in order to calculate the trap efficiency. By accurately modeling sedimentation, engineering failures such as the 2008 TVA spill at the Kingston Fossil Plant could possibly be avoided. Three different numerical models comparing the settling rates of individual particles in quiescent waters were created to compare the change of settling velocity due to particle size distributions, change of local concentrations, and flocculation …

Molecular Characterization Of Enrichment Cultures That Grow On Tetrachloroethene, 1,2 Dichloroethane And Ethylene Dibromide, Hari Shankar Peethambaram

All Theses

Halogenated aliphatic hydrocarbons are among the most common contaminants in soil and groundwater found at hazardous waste sites throughout the United States. Among them are tetrachloroethene (PCE), 1,2-dichloroethane (1,2-DCA) and ethylene dibromide (EDB). Organohalide respiration of each compound has been reported. However, considerably less information is known about EDB than PCE and 1,2-DCA, including the yield that occurs during growth with EDB as the sole TEA. The main objective of this project was to determine which types of chlororespiring microbes predominate during growth of enrichment cultures when PCE, 1,2-DCA and EDB served as the TEA, and what their yield is. …

Pharmaceuticals And Personal Care Products In Ground Water From Municipal Lagoon Treatment, Teresa Nicholas

Boise State University Theses and Dissertations

Pharmaceuticals and personal care products (PPCPs) are biologically active, organic chemicals that are introduced into the environment through wastewater streams. These chemicals are being found in the environment in trace concentrations and are of concern due to their unknown potential for harm to the health and welfare of the environment. The hypothesis is that during the course of wastewater treatment in a municipal lagoon system from a small community, PPCPs are seeping into ground water resulting in chronic low exposure in the environment. The objective of this work was to study a specific wastewater lagoon treatment system in Mountain Home, …

Sensitivity Analysis Of Uranium Speciation Modeling In Groundwater Systems With A Focus On Mobility, Andrew Scott

All Dissertations

Uranium is an important natural resource used in production of nuclear reactor fuel and nuclear weapons. The mining and processing of uranium has left a legacy of environmental contamination that remains to be addressed. There has been considerable interest in manipulating the oxidation state of uranium in order to put it into an environmentally immobile form. Uranium forms two stable oxidation states in nature, uranium (IV) being much less soluble than uranium (VI), and therefore the preferred state with regard to limiting the potential exposure of man. One of the tools used in evaluating potential effects of manipulating the natural …

Transportation Network Resiliency: A Fuzzy Systems Approach, Nayel Urena Serulle

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

Every day the dependence on transportation grows as local, regional, national, and international independence increases. Resilient transportation systems are needed to secure the highest possible level of service during disruptive events, including natural and man-made disasters. Because of limited resources, decision makers need guidance on how, when, and where to invest to improve resiliency of their networks. The research objective is to develop a method to assess and quantify resiliency, at pre-event conditions, using a fuzzy inference approach. This research expands previous work, refining key variable definitions, adjusting model interactions, and increasing transparency between metrics. This thesis presents the method …

Minimizing Base Column Demands In Multi-Story Buckling Restrained Braced Frames Using Genetic Algorithms, Christopher Hiroshi Yeates

Theses and Dissertations

Most structural optimization procedures focus on minimizing the total volume of steel in an attempt to reduce overall costs. However, many other factors can have an effect on the overall cost of a structure. Base column demands in particular, can affect base plate sizes, anchorage, and foundation design. Researchers have found that present methods for estimating column demands are too conservative. Nonlinear time history analyzes were conducted on buckling-restrained braced frames of six heights. Optimized results were found considering three ductility constraints and two optimization objectives. The two optimization objectives were minimized total brace area and minimized base column demands. …

Safety Evaluation Of Work Zone Practices In Utah, Tomás Ernesto Lindheimer

All Graduate Theses and Dissertations, Spring 1920 to Summer 2023

Work zones present a risk to drivers and to personnel constructing the roadway. In 2005 work zones accounted for 2.5% of fatalities nationwide, 3.5% for the state of Utah. The goal of this research is to make work zones safer by quantifying the risk that they present to drivers. The approach of this research has been to review part 6 of the Manual of Uniform Traffic Control Devices (MUTCD) and compare the differences from the 2003 and 2009 editions, conduct field studies of Utah work zones, and develop a tool for measuring risk in work zones. In the 2009 MUTCD …

Effect Of Ultrasonic Vibration On The Mass Transfer Coefficient In A Sieve Plate Scrubber, Dinora Monroy Melendez

All Theses

The air pollution technique of wet scrubbers for fumes, mists and suspended dusts as part of a polluted gas stream has been study as well as used for industries for many decades. The sieve tray is the simplest type of these scrubbers. A laboratory-scale single-stage, sieve tray countercurrent wet scrubber has been designed to study the effect of ultrasonic vibrations on the rate of mass transfer. A 20 kHz ultrasound frequency was chosen for a high performance cavitation to enhance the mass transport between the gas and liquid phases. Various perforation diameters and weir heights were employed in order to …

Identifying Barriers To Address During The Delivery Of Sustainable Building Renovation Projects, Corey Cattano

All Theses

Architects, engineers, and contractors are continuously searching for tools and methods to reduce the unique risks associated with the delivery of construction projects. Since national policies to reduce carbon emissions and energy consumption will require drastic improvements to the existing building stock, one specific area in need of such tools is the sustainable renovation of existing buildings. The purpose of this research is to identify the barriers to address during the delivery of sustainable renovation projects and offer solutions that overcome these barriers. For example, typical renovation projects do not coordinate energy retrofits with building system renovations, resulting in poor …