Engineering Commons^™

Effect Of Waste Covid-19 Masks On Compaction Characteristics Of Silty-Clay Soil, Sydney K. Lawson

Honors College Theses

The present study aims to explore the effect of adding shredded waste Covid-19 masks to silty-clay soil on the soil’s compaction characteristics for beneficial use in embankment, the subgrade of roadways, or backfill. This was accomplished by using two different types of masks: blue surgical masks and KN95 masks. Both mask types were hand shredded into half-inch sections using safety-scissors. The maximum dry density (MDD) and optimum moisture content (OMC) are the two most important compaction characteristics, and they were determined by the Standard Proctor Compaction Test (ASTM D698 / AASHTO T99). The change of both the MDD and OMC …

Optimizing Anaerobic Digestion Of Food Waste And Industrial Sludge For Biogas Production, Emma R. Murray

Honors College Theses

Food waste is a major contributor to municipal solid waste, and its disposal at landfills has significant environmental and economic impacts. Opportunities need to be identified for the sustainable management of food waste at large scales. Pulp and paper mills throughout the country commonly use anaerobic digestion to treat their waste sludge; however, this sludge can consist of over 50% lignin, which is slowly or negligibly digested. This research aims to explore the sustainability of co-digestion of food waste and paper mill sludge. Lab-scale studies were used to assess the feasibility of anaerobic digestion by measuring treatment efficiencies and biogas …

Simulation Of Wave Propagation In Granular Particles Using A Discrete Element Model, Syed Tahmid Hussan

Electronic Theses and Dissertations

The understanding of Bender Element mechanism and utilization of Particle Flow Code (PFC) to simulate the seismic wave behavior is important to test the dynamic behavior of soil particles. Both discrete and finite element methods can be used to simulate wave behavior. However, Discrete Element Method (DEM) is mostly suitable, as the micro scaled soil particle cannot be fully considered as continuous specimen like a piece of rod or aluminum. Recently DEM has been widely used to study mechanical properties of soils at particle level considering the particles as balls. This study represents a comparative analysis of Voigt and Best …

Innovative Research For Phosphorus Recovery In Freshwater Sediments, An Experimental Framework, John D. Collins

Honors College Theses

Phosphorus, a finite element, is necessary for all living organisms and directly impacts biota growth as well as productivity in freshwaters. The demand for phosphorus is continually increasing, but the supply of phosphorus is continually decreasing. In response to depleting resources, phosphorus in surface water sediments is being explored as a sustainable solution to the forecasted phosphorus shortage. Phosphorus in sediments is generally bound to oxidized iron (Fe3+) forming iron phosphate complexes. This form of phosphorus is released when iron reduces to Fe2+ in anaerobic environments. Under such conditions, soluble phosphorus (i.e., orthophosphate) may then be recovered using compounds that …

The Influence Of The Addition Of Recycled Asphalt Shingles On The Compressive Strength Of Concrete, William E. Webb

Honors College Theses

The purpose of this study is to explore the effect of recycled asphalt shingles (RAS) as an additive on the compressive strength of concrete. This was accomplished by designing a concrete mix and creating 4” by 8” cylindrical test specimens containing 0, 5, 10, and 15 percent RAS by weight. The compressive strength was measured through axial loading until failure utilizing a compression testing apparatus. With these results, a relationship between the content of RAS and compressive strength was able to be developed, giving insight as to how RAS could be used in concrete mixes in the future. This study …

Assessing The Ability Of Arduino-Based Sensor Systems To Monitor Changes In Water Quality, Josiah Hacker

Honors College Theses

Access to safe water is vital to public health. While developed countries like the United States are recognized as having reliable and safe water, many small water utilities struggle with supplying consistent water quality. Technicians of these utilities will periodically test water samples from the influent and throughout the distribution system. However, this laborious and costly process does not capture sudden changes in influent water quality due to environmental conditions or pipes breaking in the distribution system. Here I show how an Arduino-based sensor can be used as a real-time, low-cost monitor of water quality parameters. Specifically, I developed a …

Accessing The Relative Sustainability Of Point-Of-Use Water Disinfection Technologies Through Costs And Environmental Impacts, Bright C. Elijah

Electronic Theses and Dissertations

According to the World Health Organization, 785 million people lack access to basic drinking water facilities, and 144 million people rely on surface water which is prone to microbial contamination. Point-of-use (POU) water disinfection technologies can be adopted to help address these issues by treating water at the household level; however, navigating various POU disinfection technologies for a given water source or location can be difficult. While numerous conventional POU technologies exist (e.g., boiling water, POU chlorination), new emerging POU technologies (e.g., using novel materials or advanced processes) have been coined by developers to be lower cost with higher treatment …

Nondestructive Evaluation Of Structural Defects In Concrete Slabs, Ehsanul Kabir

Electronic Theses and Dissertations

Nondestructive testing (NDT) is a reliable method for determining the structural integrity of new and old construction and understanding the condition of structural defects. It is widely acknowledged that the interpretation of nondestructive evaluation (NDE) has a significant impact on the reliability and consistency of this technology. However, NDT data acquisition remains subjective and heavily dependent on the operator’s knowledge and expertise. As a result, there are still issues to be resolved regarding the imaging and diagnostic procedures for NDT-based concrete inspection. NDT methods such as ground penetrating radar (GPR), and impact-echo (IE), have been extensively used to inspect concrete …

Predictions Of The Dynamic Complex Modulus Of Non-Conventional Asphalt Concrete Using Machine Learning Techniques, Annie Benson

Electronic Theses and Dissertations

The complex dynamic modulus (|E*|) is a characterization property that defines the stiffness of an asphalt mixture. The dynamic modulus can be found through lab testing or predictions. Since lab testing can be time-consuming and expensive, the prediction method can be used as an alternative method. While a statistical method has been traditionally used for the |E*| prediction such as the Witczak’s predictive equations, machine learning (ML) is recently emerging as an alternative way that |E*| predictions can be made. This research attempted to predict the |E*| using several ML techniques including linear regression, support vector machines (SVM), decision trees, …

Implementation Of Ground Penetrating Radar (Gpr) And Complementary Non-Destructive Testing On Concrete Structures, Macy Spears

Electronic Theses and Dissertations

This study analyzes the application and practicality of different non-destructive testing (NDT) methods for the inspection of reinforced concrete. There are two studies discussed in this paper. The first one is a laboratory investigation, utilizing ground penetrating radar (GPR) on concrete slabs that consisted of simulated defects to mimic those found in real concrete structures. This served as a preliminary experiment to verify the GPR data with the design of the slabs. The following study describes a field investigation on an old bridge deck, which involved multiple testing methods. The techniques used were GPR, impact echo (IE), ultrasonic pulse echo …

Analysis Of Properties Of Asphalt Binder With The Addition Of Lignin, Frank A. Martin Junior

Honors College Theses

As asphalt ages, its resistance to shear diminishes due to a change in composition, resulting in the need for repaving of roads. Current additives to asphalt binder focus on increasing the strength of the binder, but do nothing to prevent the ageing of the asphalt binder. Lignin is a biological additive that is known for its resistance to ultraviolet radiation. This research aims to study Lignin as an asphalt additive, which exhibits properties that can increase the resistance of degradation due to aging, as well as increasing the strength of the asphalt binder. This was done through the comparison of …

Analysis Of Spatial Discrepancies Between 76-Foot Close Range Photogrammetric And Terrestrial-Lidar Models, Abdoul K. Ouangre

Electronic Theses and Dissertations

This study presents an analysis of the accuracy of a 3D model generated by two different methods. In the first method, the 3D model is generated via Laser Scanning. In the second method, the 3D model is generated via Close-range Photogrammetry from a drone flying at 76 feet above the ground. Photogrammetry is a photo-based technique that uses images to generate 3D models of objects where distances could be extracted from. Close-range photogrammetry is the approach of generating a 3D model from a camera placed anywhere between 1 foot and 1000 feet relative to the object. Terrestrial LiDAR is the …

Analysis Of Tensegrity Structures Using Abaqus, Kayla M. Allen

Honors College Theses

This project involves modeling and analysis of a tensegrity structure using the finite element approach utilizing the Abaqus software package. A tensegrity structure is a special type of assembly consisting of a series of straight solid members, arranged in various geometrical configurations in three-dimensional space and held together by series of cables. The developed finite element models for several tensegrity structures are included in this thesis report to better describe the project.

Current Status Of Design And Construction Of Piles With A Pilot Hole On Rock, Charles C. Crowner

Electronic Theses and Dissertations

Driven piles at project sites get their load bearing capacity from side friction along the driven lengths as well as from end resistance. Pilot holes is a pile driving assistance method used to aid driving displacement piles through hard/ dense layers and rock. These pilot holes can be a size smaller or larger than the pile that is to be installed. The pilot hole is first drilled down to a specific depth. The use of a pilot hole reduces the “end bearing” and “side resistance” within the drilled zone and aids the driving of the pile. This process also complicates …

Impact Of Blended Salt Anti-Icers/Deicers On Properties Of Asphalt Binders, Nurudeen A. Abidoye

Electronic Theses and Dissertations

Anyone who has ever attempted to remove a layer of ice from a roadway or sidewalk by plowing or shoveling knows it is no easy task when the ice is firmly bonded to the asphalt/concrete surface. Winter anti-icing/deicing operations are moral choices that mankind has made to combat winter storms. This research is aimed at evaluating the macro and nano structural impacts of (anti-icing/de-icing) salt on aged and unaged asphalt binders. The macro structural impacts focused on the rheological and creep properties, and the nano structural impacts focused on the surface topography, adhesion force, and modulus of asphalt binders. Rheological …

New Longitudinal Error Balancing Approaches For Closed Traverses, Jose L. Manzano

Electronic Theses and Dissertations

This study presents two novel approaches to balance the horizontal longitudinal error of closure, E_C, in closed polygonal traverses. The standard procedure to balance E_C is the Compass Rule. This technique reduces E_C to zero by applying corrections in the lengths of all traverse sides. Those corrections are proportional to the corresponding side lengths. That is, this approach is not an error-correcting approach, but an error-balancing procedure.

The proposed new techniques are based on sensitivity analysis of E_C with respect to small variations, Δ_i, in the lengths of all sides i = 1, …

Optimizing Anti-Icing Operation For Winter Roadway Treatment Using A Decision-Making Tool, Jyoti B. Das

Electronic Theses and Dissertations

Managing winter roadway treatment can be a challenge where winter is not severe, but snowfall is experienced a few times a year. Winter weather makes the road dangerous and challenging to travel. Most US states have approached and implemented different winter road maintenance practices to make transportation of goods, services, and people uninterrupted. However, the state of Georgia has always struggled to deal with winter weather. Recently, there has been some progress. The Georgia Department of Transportation prepared a winter road treatment plan in 2019, and they are still working on improving it. Increasing emphasis on pre-treating the road rather …

Prediction Of The Compressive Strength And Dynamic Modulus Of Fiber Reinforced Concrete By Ultrasonic Pulse Velocity Measurement At Early Ages, Daniel A. Castillo Pereira

Electronic Theses and Dissertations

This research investigates the relationship between early age ultrasonic pulse velocity and the compressive strength and dynamic modulus of steel, polypropylene, nylon, and glass fiber reinforced concrete. Previous studies prove that adding fibers to concrete alters the propagation of ultrasonic pulse velocity waves. Therefore, each type of fiber-reinforced concrete will have a unique relationship between ultrasonic pulse velocity and its compressive strength and dynamic modulus depending on fiber type, fiber volume fraction, water to cement ratio, and test age. To test this hypothesis, an experimental program comprising of one hundred eighty-nine 100 mm x 200 mm fiber reinforced concrete cylinders …

Finite Element Modeling Of Mechanically Stabilized Earth Walls Built With Welded Wire Wall Panels, Dejuan G. Solan

Electronic Theses and Dissertations

In this thesis, a finite element modeling of Mechanically Stabilized Earth (MSE) walls using welded wire wall panels was performed. The implementation of finite element modeling and analysis proved to be quite efficient in simulating the three-dimensional behavior of wall panels that are a part of MSE walls. The comprehensive finite element model included defined concrete and steel material properties in order to present both the realistic behaviors of each component in the model as well as better facilitating and increasing the accuracy of the simulation of numerous finite element analysis (FEA) cases. FEA was employed to simulate welded wire …

Accuracy Of 3d Point-Cloud And Photo-Based Models Of City Street Intersections, Mariah D. Peart

Electronic Theses and Dissertations

From Georgia Southern University’s Built Environment and Modeling lab, this study compares point positions and distance measurements completed with state-of-the-art instruments and equipment. A modern, 12-second, laser scanner, a modern unmanned aerial vehicle and a highly accurate, 1-second robotic total station were employed for this study. The latter serving as the benchmark instrument. The main objective of this quantitative comparison is to explore the accuracy and usability of a relatively large point-cloud model, as a virtual surveying tool for redesign/reconstruction purposes. This project involves the generation of large, 3D, point-cloud models of two busy and complex city street intersections. One …

Designing And Testing 3-D Printed Wafer-Box With Embedded Pzt Sensors To Identify The Shape Effect On Energy Harvesting, Ahmad Jami Safayet

Electronic Theses and Dissertations

Piezoelectric energy has been recently paid attention in the field of alternative energy. Day by day the traditional energy sources including Coal tar and oils are becoming scarce. People are heading to an alternative energy source to meet the future energy demand. Piezoelectric energy is one of the competitive energy sources compared to the conventional renewable energy sources including solar, wind, and geothermal power and so on. This energy production method bears enormous research potential because it can be used as the roadway for a new method of power generation. This research project aimed to identify which shaped wafer-box produced …

Building Information Modeling (Bim) Impact On Construction Performance, David D. John

Electronic Theses and Dissertations

This study is designed to address the need for having a measure for Construction Performance on BIM-assisted construction projects. Through this study a new Construction Key Performance Indicator (CKPI) matrix is identified and created by the author. The CKPI could be used to assess BIM-assisted projects. Utilizing a sequential mixed methodology approach, academic and practitioner perspectives are assessed. A qualitative content analysis and quantitative descriptive analysis based on demographics are conducted to establish a better understanding of BIM and Construction Performance. The academic perspective is used to assess the relevance of BIMM and CKPI indicators, and the practitioner perspective is …

Audio-Based Productivity Forecasting Of Construction Cyclic Activities, Chris A. Sabillon

Electronic Theses and Dissertations

Due to its high cost, project managers must be able to monitor the performance of construction heavy equipment promptly. This cannot be achieved through traditional management techniques, which are based on direct observation or on estimations from historical data. Some manufacturers have started to integrate their proprietary technologies, but construction contractors are unlikely to have a fleet of entirely new and single manufacturer equipment for this to represent a solution. Third party automated approaches include the use of active sensors such as accelerometers and gyroscopes, passive technologies such as computer vision and image processing, and audio signal processing. Hitherto, most …

A Case Study Of Student Veteran Efficacy In The College Of Engineering And Information Technology At Georgia Southern University, Kevin G. Finley

Electronic Theses and Dissertations

This thesis addresses the issues student veterans face in their transition from military to academic life while pursuing an undergraduate degree in the STEM fields (Science, Technology, Engineering, Math) at Georgia Southern University’s College of Engineering and Information Technology (CEIT). Historically this transition has been a difficult one. Through the implementation of a mentorship program comprised of military veterans on the staff and faculty of Georgia Southern University as well as assistance and participation from members of the case study researcher team and primary researcher this program assisted incoming military student veterans as they assimilated into the collegiate atmosphere. The …

Discrepancy Analysis Between Close-Range Photogrammetry And Terrestrial Lidar, Sam R. Newsome Jr

Electronic Theses and Dissertations

This study presents a comparison of building measurements performed on 3D models generated by two different approaches. In one approach, the models were produced via close-range photogrammetry. Such models are based on still-frame photographs that are, post-processed with commercially available photogrammetric software. In the second approach, 3D point-cloud models were generated via laser scanning. For this purpose, three case studies were conducted. The first was a simple one story structure, the second was a multi-story Maya ruin, and the third was an earth filled terrace. Several benchmarks within a closed traverse were established to serve as standard georeference points for …

Learning From Cinara: Exploring The Depths Of Participatory Water Engagement In Cali, Colombia, Zachary T. Strickland

Honors College Theses

Located within the Universidad del Valle in Cali, Colombia, CINARA is an academic institution, comprised of both engineers and social scientists, that has almost three decades of experience regarding participatory approaches to water supply and environmental sanitation. In this paper, I argue that CINARA’s work is important due to its emphasis on meaningful community participation that significantly involves communities in decisions on technical matters that are usually allocated exclusively to “experts.” Furthermore, the valuation of social considerations and non-technical knowledge found amongst CINARA’s engineers stands in distinct contrast to traditional development practices and engineering mindsets. This paper will go on …

State Of Accelerated Bridge Construction (Abc) In The United States, Mike Ofili

Honors College Theses

The purpose of this project is to develop a toolkit for the design and construction of bridges using prefabricated materials primarily to reduce the closure time and on-site construction time of newly constructed bridges or bridges undergoing renovation. The research focuses specifically on short span bridges in Georgia (40,60,80, and 120ft spans).

Areas of primary concern for this project were design, constructability, structural analysis, the use of concrete and steel girders, cost efficiency, and industry surveys. In this particular portion of the study, the surveys proved to be most effective when combined with information obtained existing research as well as …

Performance Characteristics Of Polyethylene Terephthalate (Pet) Modified Asphalt, Matthew D. Earnest

Electronic Theses and Dissertations

Polyethylene terephthalate (PET) plastic is utilized primarily in food and beverage packaging. Although a portion of waste PET is recycled, the majority of the waste is buried in landfills. Therefore, the use of ground PET particles in asphalt may provide an environmentally friendly solution for the disposal of large quantities of PET waste. This study evaluated the performance of PET as an asphalt modifier with both asphalt binder and asphalt mixture testing. The binder testing was conducted on wet process blends produced with a high shear mixer at PET contents of 5, 10, and 15 percent by weight of the …

Color Removal From Pulp Mill Effluent Using Coal Ash Produced From Georgia Power Coal Combustion Plants, Christopher B. Willett

Electronic Theses and Dissertations

Two environmental concerns currently face Georgia: coal fly ash (CFA) waste from coal power plants, and the effluent generated by pulp mills. Pulp mill effluent discolors surface waters into which it is discharged, and has been proven to negatively impact the dissolved oxygen and carbon necessary for aquatic life. The proposed solution is a cost-effective adsorption treatment using an inexpensive but abundantly available waste material: CFA. CFA possesses beneficial properties that allow it to effectively remove contaminants, and is available at significantly reduced cost. The primary research objective was to define treatment parameters that would result in the maximum removal …

Water And Nutrient Reuse Within Closed Hydroponic Systems, Emerson Christie

Electronic Theses and Dissertations

Currently, little research exists on the maintenance of individual nutrient balance within the nutrient solutions of closed hydroponic systems and how this maintenance may result in reductions in water and nutrient consumption. In this study, a nutrient solution management procedure was developed to maintain outputs while minimizing inputs. Lactuca sativa (lettuce) crops were grown in six closed hydroponic systems utilizing the nutrient film technique. Electrical conductivity was used as the primary indicator of nutrient solution quality and determined if the nutrient solution was discarded and replaced (control systems) or restored (test systems). Restorations in test systems were made individually to …