Engineering Commons^™

Parallelization Of The Advancing Front Local Reconnection Mesh Generation Software Using A Pseudo-Constrained Parallel Data Refinement Method, Kevin Mark Garner Jr.

Computer Science Theses & Dissertations

Preliminary results of a long-term project entailing the parallelization of an industrial strength sequential mesh generator, called Advancing Front Local Reconnection (AFLR), are presented. AFLR has been under development for the last 25 years at the NSF/ERC center at Mississippi State University. The parallel procedure that is presented is called Pseudo-constrained (PsC) Parallel Data Refinement (PDR) and consists of the following steps: (i) use an octree data-decomposition scheme to divide the original geometry into subdomains (octree leaves), (ii) refine each subdomain with the proper adjustments of its neighbors using the given refinement code, and (iii) combine all subdomain data into …

Onboard Autonomous Controllability Assessment For Fixed Wing Suavs, Brian Edward Duvall

Mechanical & Aerospace Engineering Theses & Dissertations

Traditionally fixed-wing small Unmanned Arial Vehicles (sUAV) are flown while in direct line of sight with commands from a remote operator. However, this is changing with the increased popularity and ready availability of low-cost flight controllers. Flight controllers provide fixed-wing sUAVs with functions that either minimize or eliminate the need for a remote operator. Since the remote operator is no longer controlling the sUAV, it is impossible to determine if the fixed-wing sUAV has proper control authority. In this work, a controllability detection system was designed, built, and flight-tested using COTS hardware. The method features in-situ measurement and analysis of …

The Effect Of Compaction Temperature And Pressure On Mechanical Properties Of 3d Printed Short Glass Fiber Composites, Pushpashree Jain Ajith Kumar Jain

Mechanical & Aerospace Engineering Theses & Dissertations

Among many thermoplastics that are used in engineering, polyamide 6 (nylon 6) is an extremely versatile engineering thermoplastic. Nylon filled with glass fibers has higher mechanical strength and high wear resistance than general purpose nylon. 3D printed composites, based on fused filament modeling, typically suffer from poor bead-to-bead bonding and relatively high void content, limiting their mechanical properties

This thesis explores the effect of compaction pressure and temperature on improving the mechanical properties of 3D printed composites. Engineering moduli in the printing and transverse to printing direction, as well as ultimate strength were measured using the tensile testing with Digital …

Conical Orbital Mechanics: A Rework Of Classic Orbit Transfer Mechanics, Cian Anthony Branco

Mechanical & Aerospace Engineering Theses & Dissertations

Simple orbital maneuvers obeying Kepler’s Laws, when taken with respect to Newton’s framework, require considerable time and effort to interpret and understand. Instead of a purely mathematical approach relying on the governing relations, a graphical geometric conceptual representation provides a useful alternative to the physical realities of orbits. Conic sections utilized within the full scope of a modified cone (frustum) were employed to demonstrate and develop a geometric approach to elliptical orbit transformations. The geometric model in-question utilizes the rotation of a plane intersecting the orbital frustum at some angle β (and the change in this angle) in a novel …

Space-Based Countermeasure For Hypersonic Glide Vehicle, Robert Joseph Fowler Iv

Mechanical & Aerospace Engineering Theses & Dissertations

The purpose of this thesis is to investigate the effectiveness of a space-based laser weapon system for countering a hypersonic glide vehicle. Hypersonic glide vehicles are an emerging type of weapon system which combine the range of ballistic missiles with the maneuverability of cruise missiles. These systems pose a unique threat to military assets not only for their expanded capabilities but also for the lack of an effective defensive countermeasure. Space-based laser weapon systems may offer a solution to this problem. The dynamics of a space-based laser system defending against a hypersonic glide vehicle are modeled first. The governing equations …

Model Based Systems Engineering For A Venture Class Launch Facility, Walter Mcgee Taraila

Mechanical & Aerospace Engineering Theses & Dissertations

A study of Model-Based Systems Engineering (MBSE) applied to a small-lift launch facility is presented. The research uses Systems Modeling Language (SysML) products and functional diagrams to document the structure, controls, electrical power, hydraulic, safety mechanisms, software, and fluid ground systems on a launch pad. The research is motivated by the need to design complex systems with an unambiguous understanding that improves communication, quality, productivity, and reduces risk. A model is developed following the ISO/IEC-15288 technical process framework. The stakeholder requirements are defined and analyzed to provide traceability to individual systems and subsystems. An architectural design is realized and implemented …

Finite Element Analysis Investigation Of Hybrid Thin-Ply Composites For Improved Performance Of Aerospace Structures, Alana M. Zahn

Mechanical & Aerospace Engineering Theses & Dissertations

Commercial and private aircraft have a need for strong yet light materials in order to have the most ideal performance possible. This study looks at the use of thin-ply composite materials to improve the performance of aircraft structures by means of weight savings and/or strength increase when compared to laminates that are composed of exclusively standard-ply materials. In order to perform an investigation based solely on finite element analysis, validation efforts were performed using test data from open hole tension, open hole compression, notched tension, and notched compression specimens. Once the models were validated sufficiently, the same modeling practices were …

Deep Learning For Remote Sensing Image Processing, Yan Lu

Computational Modeling & Simulation Engineering Theses & Dissertations

Remote sensing images have many applications such as ground object detection, environmental change monitoring, urban growth monitoring and natural disaster damage assessment. As of 2019, there were roughly 700 satellites listing “earth observation” as their primary application. Both spatial and temporal resolutions of satellite images have improved consistently in recent years and provided opportunities in resolving fine details on the Earth's surface. In the past decade, deep learning techniques have revolutionized many applications in the field of computer vision but have not fully been explored in remote sensing image processing. In this dissertation, several state-of-the-art deep learning models have been …

Mechanism Of Compaction With Wrinkle Formation During Automatic Stitching Of Dry Fabrics And The Size Effect Of Compression Molded Discontinuous Fiber-Reinforced Composites, Anibal Benjamin Beltran Laredo

Mechanical & Aerospace Engineering Theses & Dissertations

With an ever-increasing demand for composites, more ways of manufacturing them are becoming popular and widely used. Stitching of dry fabrics is an efficient method for improving delamination resistance. Discontinuous fiber reinforced composites can be used as a lightweight alternative material for metals through a process of compression molding, which allows for complex shape manufacturing while offering structural grade mechanical properties.

This study demonstrates how the stitching of dry fabrics can be adapted to more complex surfaces. The consequences of stitching of curvilinear surfaces can result in defect formation. Therefore, to understand the physical formation of possible defects, experimental characterization …

A Study Of The Aeroacoustics Of Swept Propellers For Small Unmanned Aerial Vehicles, Arthur David Wiedemann

Mechanical & Aerospace Engineering Theses & Dissertations

In recent years, small unmanned aerial vehicles (UAVs) have increased in availability and use in both public and commercial sectors. This increased use of small UAVs or “drones” has the unfortunate consequence of introducing excessive noise into communities where they operate. Implementation of noise reduction methods is necessary if we wish to see expanded use of drones in public areas. With electric propulsion, the primary source of noise is the rotor/propeller used in contemporary multi-rotor configurations. In this thesis, the aerodynamics and acoustic behavior of various swept propellers is examined with computational and experimental methods.

A family of propeller geometries …

Trajectory Simulation With Battery Modeling For Electric Powered Unmanned Aerial Vehicles, Ege Konuk

Mechanical & Aerospace Engineering Theses & Dissertations

Fixed wing electric powered unmanned aerial vehicles (UAVs) has been widely adopted for the last decade in a great number of applications. One of the primary advantages to fixed wing versus multi-rotor designs is the efficiency in forward flight with best possible range and endurance capabilities. In electrically powered air vehicles range and endurance are monitored by the State-of-Charge (SOC) of the battery. To understand the capabilities of the battery, discharge experiments can be conducted in lab environments; however, sometimes the results are difficult to integrate in flight simulations.

In this thesis, a trajectory simulation is developed that can estimate …

Through-Thickness Reinforcement And Repair Of Carbon Fiber Based Honeycomb Structures Under Flexure And Tension Of Adhesively Bonded Joints, Aleric Alden Sanders

Mechanical & Aerospace Engineering Theses & Dissertations

Repair and reinforcement of composite honeycomb structures is an area of concern as higher demands are being placed on high strength, lightweight structural materials, such as carbon fiber reinforced plastics and corresponding honeycomb structures. A common issue with these structures is when a delamination in the facesheet may form and spread, leading to a failure scenario. An investigation of adding a through thickness reinforcement (TTR) to these structures at the sample level that undergo four-point-bending, tension, and joining methods is conducted throughout this thesis. The embedding of pultruded carbon fiber rods is found to be an ideal addition to composite …

Rotorcraft Blade Angle Calibration Methods, Brian David Calvert Jr.

Mechanical & Aerospace Engineering Theses & Dissertations

The most vital system of a rotorcraft is the rotor system due to its effects on the overall flight quality of the vehicle. Therefore, it is of importance to be able to accurately determine blade position during flight so that fine adjustments can be made to ensure a safe and efficient flight. In this study, a current calibration method focusing on the pitch, flap, and lead-lag blade angles is analyzed and found to have larger than acceptable error associated with the sensor calibrations. A literature review is conducted which reveals four novel methods that can potentially increase the accuracy of …

Thermal Contact Resistance Measurement And Related Uncertainties, Amanda Elizabeth Stark

Mechanical & Aerospace Engineering Theses & Dissertations

Thermal contact resistance is an important parameter in detailed thermal analysis and design of aerospace systems. The ability to determine thermal contact resistance reliably can have a significant impact on the fidelity of thermal models—particularly for space applications. The 2004 NASA Langley Research Center thermal contact resistance test apparatus has been employed to evaluate two methods for inferring estimated interface surface temperatures so that thermal contact resistance can be calculated more accurately. The traditional method of extrapolation is a steady-state approach, while the new method utilizes inverse heat transfer techniques to account for inherent unsteadiness in these quasi-steady-state measurements. The …

A Post-Impact Behavior Of Platelet-Based Composites Produced By Compression Molding, Christopher Eugene Ervin Volle

Mechanical & Aerospace Engineering Theses & Dissertations

Prepreg-based Platelet Molded Compounds (PPMCs) are quickly becoming a widely used method for creating structural components in the aerospace and automotive industries. The discontinuous nature of the platelets used allow good formability of both complex and basic structural components; from seats on commercial airplanes to outer panels of vehicles.

This thesis will look at an important research question of these composites: how PPMCs behave under dynamic loading, e.g. impact and post-impact behavior. Impact is analyzed using recorded force and velocity data to find the absorbed energy. Digital image correlation is used with compression after impact testing to study the propagation …

Nonlinearity Index Aircraft Spin Motion Analysis With Dynamic Inversion Spin Recovery Controller Design, Jeffry Walker

Mechanical & Aerospace Engineering Theses & Dissertations

The aim of this thesis research is to extend the previous work of Tapolcai utilizing nonlinearity index theory to quantitatively analyze nonlinearities in an aircraft model and to augment these undesirable nonlinear characteristics with feedback control. In his work Tapolcai utilized a simplified rotational three degree of freedom model to analyze spin conditions of the F-18 High Angle-of-Attack Research Vehicle model. Through the application of nonlinearity index theory, regions of severe nonlinearity were uncovered exhibiting chaotic non-periodic behavior, periodic limit cycling, and instability. If these conditions were encountered during flight, the aircraft would exhibit undesirable response characteristics thereby requiring augmented …