Engineering Commons^™

Onboard Autonomous Controllability Assessment For Fixed Wing Suavs, Brian Edward Duvall

Mechanical & Aerospace Engineering Theses & Dissertations

Traditionally fixed-wing small Unmanned Arial Vehicles (sUAV) are flown while in direct line of sight with commands from a remote operator. However, this is changing with the increased popularity and ready availability of low-cost flight controllers. Flight controllers provide fixed-wing sUAVs with functions that either minimize or eliminate the need for a remote operator. Since the remote operator is no longer controlling the sUAV, it is impossible to determine if the fixed-wing sUAV has proper control authority. In this work, a controllability detection system was designed, built, and flight-tested using COTS hardware. The method features in-situ measurement and analysis of …

The Effect Of Compaction Temperature And Pressure On Mechanical Properties Of 3d Printed Short Glass Fiber Composites, Pushpashree Jain Ajith Kumar Jain

Mechanical & Aerospace Engineering Theses & Dissertations

Among many thermoplastics that are used in engineering, polyamide 6 (nylon 6) is an extremely versatile engineering thermoplastic. Nylon filled with glass fibers has higher mechanical strength and high wear resistance than general purpose nylon. 3D printed composites, based on fused filament modeling, typically suffer from poor bead-to-bead bonding and relatively high void content, limiting their mechanical properties

This thesis explores the effect of compaction pressure and temperature on improving the mechanical properties of 3D printed composites. Engineering moduli in the printing and transverse to printing direction, as well as ultimate strength were measured using the tensile testing with Digital …

Model Based Systems Engineering For A Venture Class Launch Facility, Walter Mcgee Taraila

Mechanical & Aerospace Engineering Theses & Dissertations

A study of Model-Based Systems Engineering (MBSE) applied to a small-lift launch facility is presented. The research uses Systems Modeling Language (SysML) products and functional diagrams to document the structure, controls, electrical power, hydraulic, safety mechanisms, software, and fluid ground systems on a launch pad. The research is motivated by the need to design complex systems with an unambiguous understanding that improves communication, quality, productivity, and reduces risk. A model is developed following the ISO/IEC-15288 technical process framework. The stakeholder requirements are defined and analyzed to provide traceability to individual systems and subsystems. An architectural design is realized and implemented …

Finite Element Analysis Investigation Of Hybrid Thin-Ply Composites For Improved Performance Of Aerospace Structures, Alana M. Zahn

Mechanical & Aerospace Engineering Theses & Dissertations

Commercial and private aircraft have a need for strong yet light materials in order to have the most ideal performance possible. This study looks at the use of thin-ply composite materials to improve the performance of aircraft structures by means of weight savings and/or strength increase when compared to laminates that are composed of exclusively standard-ply materials. In order to perform an investigation based solely on finite element analysis, validation efforts were performed using test data from open hole tension, open hole compression, notched tension, and notched compression specimens. Once the models were validated sufficiently, the same modeling practices were …

Mechanism Of Compaction With Wrinkle Formation During Automatic Stitching Of Dry Fabrics And The Size Effect Of Compression Molded Discontinuous Fiber-Reinforced Composites, Anibal Benjamin Beltran Laredo

Mechanical & Aerospace Engineering Theses & Dissertations

With an ever-increasing demand for composites, more ways of manufacturing them are becoming popular and widely used. Stitching of dry fabrics is an efficient method for improving delamination resistance. Discontinuous fiber reinforced composites can be used as a lightweight alternative material for metals through a process of compression molding, which allows for complex shape manufacturing while offering structural grade mechanical properties.

This study demonstrates how the stitching of dry fabrics can be adapted to more complex surfaces. The consequences of stitching of curvilinear surfaces can result in defect formation. Therefore, to understand the physical formation of possible defects, experimental characterization …

Nonlinearity Index Aircraft Spin Motion Analysis With Dynamic Inversion Spin Recovery Controller Design, Jeffry Walker

Mechanical & Aerospace Engineering Theses & Dissertations

The aim of this thesis research is to extend the previous work of Tapolcai utilizing nonlinearity index theory to quantitatively analyze nonlinearities in an aircraft model and to augment these undesirable nonlinear characteristics with feedback control. In his work Tapolcai utilized a simplified rotational three degree of freedom model to analyze spin conditions of the F-18 High Angle-of-Attack Research Vehicle model. Through the application of nonlinearity index theory, regions of severe nonlinearity were uncovered exhibiting chaotic non-periodic behavior, periodic limit cycling, and instability. If these conditions were encountered during flight, the aircraft would exhibit undesirable response characteristics thereby requiring augmented …

Thermal Contact Resistance Measurement And Related Uncertainties, Amanda Elizabeth Stark

Mechanical & Aerospace Engineering Theses & Dissertations

Thermal contact resistance is an important parameter in detailed thermal analysis and design of aerospace systems. The ability to determine thermal contact resistance reliably can have a significant impact on the fidelity of thermal models—particularly for space applications. The 2004 NASA Langley Research Center thermal contact resistance test apparatus has been employed to evaluate two methods for inferring estimated interface surface temperatures so that thermal contact resistance can be calculated more accurately. The traditional method of extrapolation is a steady-state approach, while the new method utilizes inverse heat transfer techniques to account for inherent unsteadiness in these quasi-steady-state measurements. The …

Through-Thickness Reinforcement And Repair Of Carbon Fiber Based Honeycomb Structures Under Flexure And Tension Of Adhesively Bonded Joints, Aleric Alden Sanders

Mechanical & Aerospace Engineering Theses & Dissertations

Repair and reinforcement of composite honeycomb structures is an area of concern as higher demands are being placed on high strength, lightweight structural materials, such as carbon fiber reinforced plastics and corresponding honeycomb structures. A common issue with these structures is when a delamination in the facesheet may form and spread, leading to a failure scenario. An investigation of adding a through thickness reinforcement (TTR) to these structures at the sample level that undergo four-point-bending, tension, and joining methods is conducted throughout this thesis. The embedding of pultruded carbon fiber rods is found to be an ideal addition to composite …

A Post-Impact Behavior Of Platelet-Based Composites Produced By Compression Molding, Christopher Eugene Ervin Volle

Mechanical & Aerospace Engineering Theses & Dissertations

Prepreg-based Platelet Molded Compounds (PPMCs) are quickly becoming a widely used method for creating structural components in the aerospace and automotive industries. The discontinuous nature of the platelets used allow good formability of both complex and basic structural components; from seats on commercial airplanes to outer panels of vehicles.

This thesis will look at an important research question of these composites: how PPMCs behave under dynamic loading, e.g. impact and post-impact behavior. Impact is analyzed using recorded force and velocity data to find the absorbed energy. Digital image correlation is used with compression after impact testing to study the propagation …

Rotorcraft Blade Angle Calibration Methods, Brian David Calvert Jr.

Mechanical & Aerospace Engineering Theses & Dissertations

The most vital system of a rotorcraft is the rotor system due to its effects on the overall flight quality of the vehicle. Therefore, it is of importance to be able to accurately determine blade position during flight so that fine adjustments can be made to ensure a safe and efficient flight. In this study, a current calibration method focusing on the pitch, flap, and lead-lag blade angles is analyzed and found to have larger than acceptable error associated with the sensor calibrations. A literature review is conducted which reveals four novel methods that can potentially increase the accuracy of …

A Study Of The Aeroacoustics Of Swept Propellers For Small Unmanned Aerial Vehicles, Arthur David Wiedemann

Mechanical & Aerospace Engineering Theses & Dissertations

In recent years, small unmanned aerial vehicles (UAVs) have increased in availability and use in both public and commercial sectors. This increased use of small UAVs or “drones” has the unfortunate consequence of introducing excessive noise into communities where they operate. Implementation of noise reduction methods is necessary if we wish to see expanded use of drones in public areas. With electric propulsion, the primary source of noise is the rotor/propeller used in contemporary multi-rotor configurations. In this thesis, the aerodynamics and acoustic behavior of various swept propellers is examined with computational and experimental methods.

A family of propeller geometries …

Trajectory Simulation With Battery Modeling For Electric Powered Unmanned Aerial Vehicles, Ege Konuk

Mechanical & Aerospace Engineering Theses & Dissertations

Fixed wing electric powered unmanned aerial vehicles (UAVs) has been widely adopted for the last decade in a great number of applications. One of the primary advantages to fixed wing versus multi-rotor designs is the efficiency in forward flight with best possible range and endurance capabilities. In electrically powered air vehicles range and endurance are monitored by the State-of-Charge (SOC) of the battery. To understand the capabilities of the battery, discharge experiments can be conducted in lab environments; however, sometimes the results are difficult to integrate in flight simulations.

In this thesis, a trajectory simulation is developed that can estimate …

Extension Of A Penalty Method For Numerically Solving Constrained Multibody Dynamic Problems, Troy Newhart

Mechanical & Aerospace Engineering Theses & Dissertations

Numerical analysis of constrained static and multibody dynamic systems has become an integral part of engineering analysis with the continued improvements in technology and software availability. Many methods currently exist for numerically solving constrained static and dynamic systems. The applicability of a penalty method for constrained static solutions is observed in many academic texts and papers. The appeal for using a penalty method in statics pertains to its ease of implementation, computational suitability, and accuracy. This thesis extends a static penalty method for use with constrained multibody dynamics to observe if the penalty method’s benefits are similar for a dynamics …

Periodic Orbit Analytic Construction In The Circular Restricted Three-Body Problem, Jay Shriram Suryawanshi

Mechanical & Aerospace Engineering Theses & Dissertations

This thesis investigates an approximate analytic construction of halo-type periodic orbits about the collinear equilibrium points in the circular restricted three-body problem. The research follows a parallel approach to the one used by Ghazy and Newman, but the initial assumptions and utilized functions are unique to this thesis. A suppositional base solution constructed using Jacobi elliptic functions and satisfying Jacobi's integral equation is at the core of the analytic construction framework. The locus of this solution is a circle lying in the plane perpendicular to the line joining the primaries. The base solution elicits a closed-form expression for the period …

Reducing The Noise Impact Of Unmanned Aerial Vehicles By Flight Control System Augmentation, Matthew B. Galles

Mechanical & Aerospace Engineering Theses & Dissertations

The aim of this thesis is to explore methods to reduce the noise impact of unmanned aerial vehicles operating within acoustically sensitive environments by flight control system augmentation. Two methods are investigated and include: (i) reduction of sound generated by vehicle speed control while flying along a nominal path and (ii) reduction of acoustic exposure by vehicle path control while flying at a nominal speed. Both methods require incorporation of an acoustic model into the flight control system as an additional control objective and an acoustic metric to characterize primary noise sources dependent on vehicle state. An acoustic model was …

Comparison Of Support Methods For Static Aerodynamic Testing And Validation Of A Magnetic Suspension And Balance System, Cameron K. Neill

Mechanical & Aerospace Engineering Theses & Dissertations

Magnetic suspension wind tunnels offer an alternative to traditional physical support methods. They allow for the collection of support interference free data and broader dynamic test capabilities than existing methods. Determination of dynamic aerodynamic characteristics is a crucial portion of the design of new re-entry capsules. A NASA initiative restored the 6-inch Magnetic Suspension and Balance System to support the design of a new MSBS for a supersonic wind tunnel. Before a new MSBS can be constructed, the characteristics of the current MSBS must be examined.

This thesis discusses the calibration and validation of the 6-inch MSBS. After calibration, three …

Design And Manufacture Of An Inertial Cascade Impactor For Industrial Hygiene Purposes, Hector Joel Gortaire

Mechanical & Aerospace Engineering Theses & Dissertations

Inertial cascade impactors are devices commonly used for industrial hygiene and pharmaceutical studies. Their main purpose is to separate particulate matter suspended in aerosols according to their sizes, which can vary from over 10 µm to 0.5 µm. Their versatility and ease of operation make them suitable for on-site sampling; however, designing them requires a careful consideration of the different geometric parameters that characterize them.

In this thesis, a 5-stage inertial cascade impactor was designed, modelled, constructed, and tested. The main design parameter was the volumetric flow rate, 40 l/min, which was provided by a vacuum pump. By continuous iterations, …

Characterization And Optimization Of A Propeller Test Stand, Colin Bruce Leighton Benjamin

Mechanical & Aerospace Engineering Theses & Dissertations

In recent history, there has been a rapid rise in the use of drones, and they are expanding in popularity each year. The widespread use and future capabilities of these unmanned aerial vehicles (UAVs) will call for increased study and classification of propellers to maximize their performance. As a result, it is necessary to have continuity in the development, maximization, and optimization of propeller test stand’s capability to collect accurate and precise measurements. It is of significant advantage to have the capability of accurately characterizing a propeller based on its thrust and torque. In this study, a propeller test stand …

Aerothermodynamic Analysis Of A Mars Sample Return Earth-Entry Vehicle, Daniel A. Boyd

Mechanical & Aerospace Engineering Theses & Dissertations

Because of the severe quarantine constraints that must be imposed on any returned extraterrestrial samples, the Mars sample return Earth-entry vehicle must remain intact through sample recovery. Vehicles returning on a Mars-Earth trajectory will attain velocities exceeding any that have been experienced by prior space exploration missions, with velocities approaching 14 km/s. Velocities as high as these will encounter significant heating during atmospheric re-entry to Earth.

The purpose of this study has been to systematically investigate the aerothermodynamic challenges that will result from a Mars sample return, Earth-entry vehicle design. The goal was to enable efficient estimation of maximum stagnation …

Effects Of Automated Fiber Placement On High Strain Rate Compressive Response Of Advanced Composites, Alexander Trochez

Mechanical & Aerospace Engineering Theses & Dissertations

Automated Fiber Placement (AFP) technology shows great promise in manufacturing carbon fiber composite structures. However, intermittent defects occur in the process that can affect the overall mechanical performance of the structure. The aim of this work is to investigate the effects of deliberately placed principal defects (Gap, Overlap, and Fold) on the compressive response under quasistatic (strain rate ~10^-3 s^-1) and dynamic (strain rate ~10³ s-1) loading conditions. The controlled defects were placed at the laminate level in different orientations and depths. High strain rate compression experiments were conducted using a split Hopkinson pressure bar (SHPB) …

A Cost Effective Design For A Propeller Thrust/Torque Balance, Nicholas Barrett Sadowski

Mechanical & Aerospace Engineering Theses & Dissertations

Wind tunnel balances are used with aircraft models, propellers, and components to measure applied forces and moments. The design and manufacture of a balance is often for a specific test, test article and conditions. This paper discusses the theory, design, calibration, and testing of a new small propeller balance for use in a low-speed wind tunnel. The new balance is named the ODU15X15.

Theory discussed herein covers how the two measurement components, thrust and torque, affect the balance design. These loads generate strains which are in turn read by strain gages arranged in Wheatstone bridges. The design follows well known …

Design And Implementation Of An Artificial Neural Network Controller For Quadrotor Flight In Confined Environment, Ahmed Mekky

Mechanical & Aerospace Engineering Theses & Dissertations

Quadrotors offer practical solutions for many applications, such as emergency rescue, surveillance, military operations, videography and many more. For this reason, they have recently attracted the attention of research and industry. Even though they have been intensively studied, quadrotors still suffer from some challenges that limit their use, such as trajectory measurement, attitude estimation, obstacle avoidance, safety precautions, and land cybersecurity. One major problem is flying in a confined environment, such as closed buildings and tunnels, where the aerodynamics around the quadrotor are affected by close proximity objects, which result in tracking performance deterioration, and sometimes instability. To address this …

Volterra Series Approximation For Multi-Degree Of Freedom, Multi-Input, Multi-Output, Aircraft Dynamics, Alexander J. Chen

Mechanical & Aerospace Engineering Theses & Dissertations

An analytical model of a second order system is extended from a single-axis framework, to a multi-axis, multi-degree of freedom framework for a multiple input, multiple output system. This mathematical model is built from the variational approach of the Volterra series representation of nonlinear systems. The new representation describes the second order, oscillatory natural modes of a system, and shows how to organize the Volterra terms in intuitive ways. The constructed mathematical model aims to establish an organization of the Volterra kernels to allow for analytical cause and effect type analysis on system behavior.

To demonstrate the accuracy of the …

Distributed Sensing And System Identification Of Cantilever Beams And Plates In The Presence Of Weak Nonlinearities, Patrick Sean Heaney

Mechanical & Aerospace Engineering Theses & Dissertations

While the mathematical foundation for modal analysis of continuous systems has long been established, flexible structures have become increasingly widespread and developing tools for understanding their mechanics has become increasingly important. Cantilever beams and plates, in particular, have been extensively studied due to their practical importance as approximations of more complex structures. The focus of this thesis is on understanding the dynamics of vibrating cantilever beams and plates through analytical and experimental investigation. Various models for the mechanics of these structures, of varying physical fidelity, are described and compared. A fiber optic sensing system is utilized to experimentally acquire distributed …

Human-Robot Collaborative Force-Controlled Micro-Drilling For Advanced Manufacturing And Medical Applications, Parimal Mahesh Prajapati

Mechanical & Aerospace Engineering Theses & Dissertations

Robotic drilling finds applications in diverse fields ranging from advanced manufacturing to the medical industry. Recent advances in low-cost, and human-safe, collaborative robots (e.g., Sawyer) are enabling us to rethink the possibilities in which robots can be deployed for such tedious and time-consuming tasks. This thesis presents a robotic drilling methodology with features of force-control enabled micro-drilling and human-robot collaboration to reduce programming efforts and enhance drilling performance. A Sawyer robot from Rethink Robotics, which offers safe physical interactions with a human co-worker, kinesthetic teaching, and force control, is used as the test bed. The robot’s end-effector was equipped with …

A Monolithic Internal Strain-Gage Balance Design Based On Design For Manufacturability, Thomas Ladson Webb Iii

Mechanical & Aerospace Engineering Theses & Dissertations

This paper proposes an alternative approach to internal strain-gage balance design driven by Design for Manufacturability (DFM) principles. The objective of this research was a reduction in fabrication time and, subsequently, cost of a balance by simplifying its design while maintaining basic stiffness and sensitivity. Traditionally, the National Aeronautics and Space Administration (NASA) Langley Research Center (LaRC) balance designs have relied on Electro-Discharge Machining (EDM), which is a precise but slow and, therefore, expensive process. EDM is chosen due to several factors, including material hardness, surface finish, and complex geometry, including blind cuts. The new balance design objectives require no …

Gust Alleviation System For General Aviation Aircraft, Lucas Coleman Mills

Mechanical & Aerospace Engineering Theses & Dissertations

A designed control motion scheme to improve passenger comfort in general aviation aircraft by reducing normal acceleration and pitch rate due to turbulence is investigated. An aerodynamic math model is created for ViGYAN’s Active Ride Improvement System flight article, a one-eighth scale Pilatus Porter PC-6 with conventional forward main wing, aft horizontal and vertical tails, and a single engine with tractor configuration. The test article incorporates a full-span gust flap and forward mounted gust sensor to mechanize the gust alleviation control system, and these features are present in the dynamic model. The model is a two degree of freedom linear …

Development Of A Data Acquisition System For Unmanned Aerial Vehicle (Uav) System Identification, Donald Joseph Lear

Mechanical & Aerospace Engineering Theses & Dissertations

Aircraft system identification techniques are developed for fixed wing Unmanned Aerial Vehicles (UAV). The use of a designed flight experiment with measured system inputs/outputs can be used to derive aircraft stability derivatives. This project set out to develop a methodology to support an experiment to model pitch damping in the longitudinal short-period mode of a UAV. A Central Composite Response Surface Design was formed using angle of attack and power levels as factors to test for the pitching moment coefficient response induced by a multistep pitching maneuver.

Selecting a high-quality data acquisition platform was critical to the success of the …

Computational Methods For Nonlinear Systems Analysis With Applications In Mathematics And Engineering, Geoffrey Kenneth Rose

Mechanical & Aerospace Engineering Theses & Dissertations

An investigation into current methods and new approaches for solving systems of nonlinear equations was performed. Nontraditional methods for implementing arc-length type solvers were developed in search of a more robust capability for solving general systems of nonlinear algebraic equations. Processes for construction of parameterized curves representing the many possible solutions to systems of equations versus finding single or point solutions were established. A procedure based on these methods was then developed to identify static equilibrium states for solutions to multi-body-dynamic systems. This methodology provided for a pictorial of the overall solution to a given system, which demonstrated the possibility …

Investigation, Modeling And Validation Of Digital Bridge For A New Generation Hot-Wire Anemometer, Karthik Kamalakar Joshi

Mechanical & Aerospace Engineering Theses & Dissertations

The Digital Bridge Thermal Anemometer (DBTA) is a new generation anemometer that uses advanced electronics and a modified half-Wheatstone bridge configuration, specifically a sensor and a shunt resistor in series. This allows the miniaturization of the anemometer and the communication between host computer and anemometer is carried out using serial or ethernet which eliminates the noise due to the use of long cables in conventional anemometer and the digital data sent to host computer is immune to electrical noise. In the new configuration the potential drop across a shunt resistor is used to control the bridge.

This thesis is confined …